Marc A. Meyers

Bio: Marc A. Meyers is an academic researcher from University of California, San Diego. The author has contributed to research in topics: Deformation (engineering) & Dislocation. The author has an hindex of 85, co-authored 487 publications receiving 36646 citations. Previous affiliations of Marc A. Meyers include University of California & Instituto Militar de Engenharia.

Self organization of shear bands in stainless steel

Abstract: The spatial distribution of shear bands was investigated in 304L stainless steel through the radial collapse of a thick-walled cylinder under high-strain-rate deformation (∼10 4 s −1 ). The shear-band initiation and propagation were also examined. Self-organization of multiple adiabatic shear bands was observed. The effect of grain size on spacing of shear bands was investigated at four different grain sizes: 30 m, 50m, 140m and 280m. A single crystal with a similar composition was also tested. The experimental results show only a modest variation of shear-band spacing within the investigated grain size range. Three principal mechanisms are considered to be active in initiation: (a) momentum diffusion by stress unloading, (b) perturbation in the stress/strain/temperature fields, (c) microstructural inhomogeneities. The observed shear-band spacing is compared with existing theories; Grady–Kipp and Wright–Ockendon–Molinari theories. These are one-dimensional theories that do not consider the evolution in spacing as the shear bands grow. A discontinuous growth mode for shear localization under periodic perturbation is applied and predicts spacings in good agreement with observations. Self-organized initiation and propagation modes are discussed in relation to the interaction among the nucleus and well-developed shear bands. © 2004 Elsevier B.V. All rights reserved.

On the effect of grain size on yield stress: extension into nanocrystalline domain

Abstract: Four principal factors contribute to grain-boundary strengthening: (a) the grain boundaries act as barriers to plastic flow; (b) the grain boundaries act as dislocation sources; (c) elastic anisotropy causes additional stresses in grain-boundary surroundings; (d) multislip is activated in the grain-boundary regions, whereas grain interiors are initially dominated by single slip, if properly oriented. As a result, the regions adjoining grain boundaries harden at a rate much higher than grain interiors. A phenomenological constitutive equation predicting the effect of grain size on the yield stress of metals is discussed and extended to the nanocrystalline regime. At large grain sizes, it has the Hall–Petch form, and in the nanocrystalline domain the slope gradually decreases until it asymptotically approaches the flow stress of the grain boundaries. The material is envisaged as a composite, comprised of the grain interior, with flow stress σfB and grain boundary work-hardened layer, with flow stress σfGB. The predictions of this model are compared with experimental measurements over the mono, micro, and nanocrystalline domains. Computational predictions are made of plastic flow as a function of grain size incorporating differences of dislocation accumulation rate in grain-boundary regions and grain interiors. The material is modeled as a monocrystalline core surrounded by a mantle (grain-boundary region) with a high work hardening rate response. This is the first computational plasticity calculation that accounts for grain size effects in a physically-based manner.

Effect of metallurgical parameters on shear band formation in low-carbon (∼0.20 Wt Pct) steels

Abstract: With the objective of establishing the effects of the metallurgical condition on the propensity to form adiabatic shear bands, low-carbon steels (AISI 1018 and 8620) having widely different temperability responses were subjected to impact by cylindrical projectiles in the velocity range of 450 to 1050 m/s. These steels received a variety of mechanical and thermal treatments that provided a wide range of microstructures and mechanical responses. The propensity for shear band formation was strongly dependent on the mechanical response. It was measured by counting the length of shear bands per cross section. Microstructural characterization of the bands revealed that white-etching bands were only observed in the quenched and quenched-and-tempered conditions.

Fast parallel algorithms for short-range molecular dynamics

Abstract: Three parallel algorithms for classical molecular dynamics are presented. The first assigns each processor a fixed subset of atoms; the second assigns each a fixed subset of inter-atomic forces to compute; the third assigns each a fixed spatial region. The algorithms are suitable for molecular dynamics models which can be difficult to parallelize efficiently—those with short-range forces where the neighbors of each atom change rapidly. They can be implemented on any distributed-memory parallel machine which allows for message-passing of data between independently executing processors. The algorithms are tested on a standard Lennard-Jones benchmark problem for system sizes ranging from 500 to 100,000,000 atoms on several parallel supercomputers--the nCUBE 2, Intel iPSC/860 and Paragon, and Cray T3D. Comparing the results to the fastest reported vectorized Cray Y-MP and C90 algorithm shows that the current generation of parallel machines is competitive with conventional vector supercomputers even for small problems. For large problems, the spatial algorithm achieves parallel efficiencies of 90% and a 1840-node Intel Paragon performs up to 165 faster than a single Cray C9O processor. Trade-offs between the three algorithms and guidelines for adapting them to more complex molecular dynamics simulations are also discussed.

Using Multivariate Statistics

Abstract: Thank you for downloading using multivariate statistics. As you may know, people have look hundreds times for their favorite novels like this using multivariate statistics, but end up in infectious downloads. Rather than reading a good book with a cup of tea in the afternoon, instead they juggled with some harmful bugs inside their laptop. using multivariate statistics is available in our digital library an online access to it is set as public so you can download it instantly. Our books collection saves in multiple locations, allowing you to get the most less latency time to download any of our books like this one. Merely said, the using multivariate statistics is universally compatible with any devices to read.

Phd by thesis

Abstract: Deposits of clastic carbonate-dominated (calciclastic) sedimentary slope systems in the rock record have been identified mostly as linearly-consistent carbonate apron deposits, even though most ancient clastic carbonate slope deposits fit the submarine fan systems better. Calciclastic submarine fans are consequently rarely described and are poorly understood. Subsequently, very little is known especially in mud-dominated calciclastic submarine fan systems. Presented in this study are a sedimentological core and petrographic characterisation of samples from eleven boreholes from the Lower Carboniferous of Bowland Basin (Northwest England) that reveals a >250 m thick calciturbidite complex deposited in a calciclastic submarine fan setting. Seven facies are recognised from core and thin section characterisation and are grouped into three carbonate turbidite sequences. They include: 1) Calciturbidites, comprising mostly of highto low-density, wavy-laminated bioclast-rich facies; 2) low-density densite mudstones which are characterised by planar laminated and unlaminated muddominated facies; and 3) Calcidebrites which are muddy or hyper-concentrated debrisflow deposits occurring as poorly-sorted, chaotic, mud-supported floatstones. These

Strength and breaking mechanism of multiwalled carbon nanotubes under tensile load

Abstract: The tensile strengths of individual multiwalled carbon nanotubes (MWCNTs) were measured with a “nanostressing stage” located within a scanning electron microscope. The tensile-loading experiment was prepared and observed entirely within the microscope and was recorded on video. The MWCNTs broke in the outermost layer (“sword-in-sheath” failure), and the tensile strength of this layer ranged from 11 to 63 gigapascals for the set of 19 MWCNTs that were loaded. Analysis of the stress-strain curves for individual MWCNTs indicated that the Young's modulus E of the outermost layer varied from 270 to 950 gigapascals. Transmission electron microscopic examination of the broken nanotube fragments revealed a variety of structures, such as a nanotube ribbon, a wave pattern, and partial radial collapse.