Michael P Sealy

Bio: Michael P Sealy is an academic researcher from University of Nebraska–Lincoln. The author has contributed to research in topics: Peening & Surface integrity. The author has an hindex of 15, co-authored 51 publications receiving 1193 citations. Previous affiliations of Michael P Sealy include University of Alabama.

Mechanical Characterizations of 3D-printed PLLA/Steel Particle Composites.

Abstract: The objective of this study is to characterize the micromechanical properties of poly-l-lactic acid (PLLA) composites reinforced by grade 420 stainless steel (SS) particles with a specific focus on the interphase properties. The specimens were manufactured using 3D printing techniques due to its many benefits, including high accuracy, cost effectiveness and customized geometry. The adopted fused filament fabrication resulted in a thin interphase layer with an average thickness of 3 µm. The mechanical properties of each phase, as well as the interphase, were characterized by nanoindentation tests. The effect of matrix degradation, i.e., imperfect bonding, on the elastic modulus of the composite was further examined by a representative volume element (RVE) model. The results showed that the interphase layer provided a smooth transition of elastic modulus from steel particles to the polymeric matrix. A 10% volume fraction of steel particles could enhance the elastic modulus of PLLA polymer by 31%. In addition, steel particles took 37% to 59% of the applied load with respect to the particle volume fraction. We found that degradation of the interphase reduced the elastic modulus of the composite by 70% and 7% under tensile and compressive loads, respectively. The shear modulus of the composite with 10% particles decreased by 36%, i.e., lower than pure PLLA, when debonding occurred.

Surface integrity and process mechanics of laser shock peening of novel biodegradable magnesium-calcium (Mg-Ca) alloy

Abstract: Current permanent metallic biomaterials of orthopedic implants, such as titanium, stainless steel, and cobalt–chromium alloys, have excellent corrosive properties and superior strengths However, their strengths are often too high resulting in a stress shielding effect that is detrimental to the bone healing process Without proper healing, costly and painful revision surgeries may be required The close Young’s modulus between magnesium-based implants and cancellous bones has the potential to minimize stress shielding while providing both biocompatibility and adequate mechanical properties The problem with Mg implants is how to control corrosion rates so that the degradation of Mg implants matches that of bone growth Laser shock peening (LSP) is an innovative surface treatment method to impart compressive residual stress to a novel Mg–Ca implant The high compressive residual stress has great potential to slow corrosion rates Therefore, LSP was initiated in this study to investigate surface topography and integrity produced by sequential peening a Mg–Ca alloy Also, a 3D semi-infinite simulation was developed to predict the topography and residual stress fields produced by sequential peening The dynamic mechanical behavior of the biomaterial was modeled using a user material subroutine from the internal state variable plasticity model The temporal and spatial peening pressure was modeled using a user load subroutine The simulated dent agrees with the measured dent topography in terms of profile and depth Sequential peening was found to increase the tensile pile up region which is critical to orthopedic applications The predicted residual stress profiles are also presented

State-of-the-art in surface integrity in machining of nickel-based super alloys

Abstract: Nickel-based super alloys are gaining more significance, now-a-days, with extensive applications in aerospace, marine, nuclear reactor and chemical industries. Several characteristics including superior mechanical and chemical properties at elevated temperature, high toughness and ductility, high melting point, excellent resistance to corrosion, thermal shocks, thermal fatigue and erosion are primarily responsible for wide domain of application. Nevertheless, machined surface integrity of nickel-based super alloys is a critical aspect which influences functional performance including fatigue life of the component. This review paper presents state-of-the-art on various surface integrity characteristics during machining of nickel-based super alloys. Influence of various cutting parameters, cutting environment, coating, wear and edge geometry of cutting tools on different features of surface integrity has been critically explained. These characteristics encompass surface roughness, defects (surface cavities, metal debris, plucking, smeared material, redeposited material, cracked carbide particles, feed marks, grooves and laps), metallurgical aspects in the form of surface and sub-surface microstructure phase transformation, dynamic recrystallisation and grain refinement and mechanical characteristics such as work hardening and residual stress. Microstructural modification of deformed layer, profile of residual stresses and their influence on fatigue durability have been given significant emphasis. Future research endeavour might focus on development of new grades, advanced processing techniques of the same to ensure their superior stability of microstructure and thermo-mechanical properties along with advanced manufacturing processes like additive manufacturing to achieve highest level of fatigue durability of safety critical components while maintaining acceptable surface integrity and productivity.

Invited review article: Strategies and processes for high quality wire arc additive manufacturing

Abstract: Wire Arc Additive Manufacturing (WAAM) is attracting significant attention in industry and academia due to its ability to capture the benefits of additive manufacturing for production of large components of medium geometric complexity. Uniquely, WAAM combines the use of wire and electric arc as a fusion source to build components in a layer-by-layer approach, both of which can offer significant cost savings compared to powder and alternative fusion sources, such as laser and electron beam, respectively. Meanwhile, a high deposition rate, key for producing such components, is provided, whilst also allowing significant material savings compared to conventional manufacturing processes. However, high quality production in a wide range of materials is limited by the elevated levels of heat input which causes a number of materials processing challenges in WAAM. The materials processing challenges are fully identified in this paper to include the development of high residual stresses, undesirable microstructures, and solute segregation and phase transformations at solidification. The thermal profile during the build poses another challenge leading to heterogeneous and anisotropic material properties. This paper outlines how the materials processing challenges may be addressed in WAAM by implementation of quality improving ancillary processes. The primary WAAM process selections and ancillary processes are classified by the authors and a comprehensive review of their application conducted. Strategies by which the ancillary processes can enhance the quality of WAAM parts are presented. The efficacy and suitability of these strategies for versatile and cost effective WAAM production are discussed and a future vision of WAAM process developments provided.

Material-structure-performance integrated laser-metal additive manufacturing.

Abstract: BACKGROUND Metallic components are the cornerstone of modern industries such as aviation, aerospace, automobile manufacturing, and energy production. The stringent requirements for high-performance metallic components impede the optimization of materials selection and manufacturing. Laser-based additive manufacturing (AM) is a key strategic technology for technological innovation and industrial sustainability. As the number of applications increases, so do the scientific and technological challenges. Because laser AM has domain-by-domain (e.g., point-by-point, line-by-line, and layer-by-layer) localized forming characteristics, the requisite for printing process and performance control encompasses more than six orders of magnitude, from the microstructure (nanometer- to micrometer-scale) to macroscale structure and performance of components (millimeter- to meter-scale). The traditional route of laser-metal AM follows a typical “series mode” from design to build, resulting in a cumbersome trial-and-error methodology that creates challenges for obtaining high-performance goals. ADVANCES We propose a holistic concept of material-structure-performance integrated additive manufacturing (MSPI-AM) to cope with the extensive challenges of AM. We define MSPI-AM as a one-step AM production of an integral metallic component by integrating multimaterial layout and innovative structures, with an aim to proactively achieve the designed high performance and multifunctionality. Driven by the performance or function to be realized, the MSPI-AM methodology enables the design of multiple materials, new structures, and corresponding printing processes in parallel and emphasizes their mutual compatibility, providing a systematic solution to the existing challenges for laser-metal AM. MSPI-AM is defined by two methodological ideas: “the right materials printed in the right positions” and “unique structures printed for unique functions.” The increasingly creative methods for engineering both micro- and macrostructures within single printed components have led to the use of AM to produce more complicated structures with multimaterials. It is now feasible to design and print multimaterial components with spatially varying microstructures and properties (e.g., nanocomposites, in situ composites, and gradient materials), further enabling the integration of functional structures with electronics within the volume of a laser-printed monolithic part. These complicated structures (e.g., integral topology optimization structures, biomimetic structures learned from nature, and multiscale hierarchical lattice or cellular structures) have led to breakthroughs in both mechanical performance and physical/chemical functionality. Proactive realization of high performance and multifunctionality requires cross-scale coordination mechanisms (i.e., from the nano/microscale to the macroscale). OUTLOOK Our MSPI-AM continues to develop into a practical methodology that contributes to the high performance and multifunctionality goals of AM. Many opportunities exist to enhance MSPI-AM. MSPI-AM relies on a more digitized material and structure development and printing, which could be accomplished by considering different paradigms for AM materials discovery with the Materials Genome Initiative, standardization of formats for digitizing materials and structures to accelerate data aggregation, and a systematic printability database to enhance autonomous decision-making of printers. MSPI-oriented AM becomes more intelligent in processes and production, with the integration of intelligent detection, sensing and monitoring, big-data statistics and analytics, machine learning, and digital twins. MSPI-AM further calls for more hybrid approaches to yield the final high-performance/multifunctional achievements, with more versatile materials selection and more comprehensive integration of virtual manufacturing and real production to navigate more complex printing. We hope that MSPI-AM can become a key strategy for the sustainable development of AM technologies. Download high-res image Open in new tab Download Powerpoint Material-structure-performance integrated additive manufacturing (MSPI-AM). Versatile designed materials and innovative structures are simultaneously printed within an integral metallic component to yield high performance and multifunctionality, integrating in parallel the core elements of material, structure, process, and performance and a large number of related coupling elements and future potential elements to enhance the multifunctionality of printed components and the maturity and sustainability of laser AM technologies.