Michele Chiumenti

Bio: Michele Chiumenti is an academic researcher from Polytechnic University of Catalonia. The author has contributed to research in topics: Finite element method & Friction stir welding. The author has an hindex of 32, co-authored 133 publications receiving 3142 citations. Previous affiliations of Michele Chiumenti include Polytechnic University of Puerto Rico & Université catholique de Louvain.

Residual stress and distortion of rectangular and S-shaped Ti-6Al-4V parts by Directed Energy Deposition: Modelling and experimental calibration

Abstract: Residual stresses and distortion in Additive Manufactured (AM) parts are two key obstacles which seriously hinder the wide application of this technology. Nowadays, understanding the thermomechanical behavior induced by the AM process is still a complex task which must take into account the effects of both the process and the material parameters, the microstructure evolution as well as the pre-heating strategy. One of the challenges of this work is to increase the complexity of the geometries used to study the thermomechanical behavior induced by the AM process. The reference geometries are a rectangular and a S-shaped structures made of 44-layers each. The samples have been fabricated by Directed Energy Deposition (DED). In-situ thermal and distortion histories of the substrate are measured in order to calibrate the 3D coupled thermo-mechanical model. Once the numerical results showed a good agreement with the temperature measurements, the validated model has been used to predict the residual stresses and distortions. Different process parameters have been analyzed to study their sensitivity to the process assessment. Different preheating strategies have been also analyzed to check their effectiveness on the mitigation of both distortions and residual stresses. Finally, some simplifications of the actual scanning sequence are proposed to reduce the computational cost without loss of the accuracy of the simulation framework.

Smeared crack approach: back to the original track

Abstract: This paper briefly reviews the formulations used over the last 40 years for the solution of problems involving tensile cracking, with both the discrete and the smeared crack approaches. The paper focuses on the smeared approach, identifying as its main drawbacks the observed mesh-size and mesh-bias spurious dependence when the method is applied ‘straightly’. A simple isotropic local damage constitutive model is considered, and the (exponential) softening modulus is regularized according to the material fracture energy and the element size. The continuum and discrete mechanical problems corresponding to both the weak discontinuity (smeared cracks) and the strong discontinuity (discrete cracks) approaches are analysed and the question of propagation of the strain localization band (crack) is identified as the main difficulty to be overcome in the numerical procedure. A tracking technique is used to ensure stability of the solution, attaining the necessary convergence properties of the corresponding discrete finite element formulation. Numerical examples show that the formulation derived is stable and remarkably robust. As a consequence, the results obtained do not suffer from spurious mesh-size or mesh-bias dependence, comparing very favourably with those obtained with other fracture and continuum mechanics approaches. Copyright © 2006 John Wiley & Sons, Ltd.

Phd by thesis

Abstract: Deposits of clastic carbonate-dominated (calciclastic) sedimentary slope systems in the rock record have been identified mostly as linearly-consistent carbonate apron deposits, even though most ancient clastic carbonate slope deposits fit the submarine fan systems better. Calciclastic submarine fans are consequently rarely described and are poorly understood. Subsequently, very little is known especially in mud-dominated calciclastic submarine fan systems. Presented in this study are a sedimentological core and petrographic characterisation of samples from eleven boreholes from the Lower Carboniferous of Bowland Basin (Northwest England) that reveals a >250 m thick calciturbidite complex deposited in a calciclastic submarine fan setting. Seven facies are recognised from core and thin section characterisation and are grouped into three carbonate turbidite sequences. They include: 1) Calciturbidites, comprising mostly of highto low-density, wavy-laminated bioclast-rich facies; 2) low-density densite mudstones which are characterised by planar laminated and unlaminated muddominated facies; and 3) Calcidebrites which are muddy or hyper-concentrated debrisflow deposits occurring as poorly-sorted, chaotic, mud-supported floatstones. These

American Society for Testing and Materials

Abstract: The American Society for Testing and Materials (ASTM) is an independent organization devoted to the development of standards.