Currently, the growth of tannery industries causes a significant volume of waste disposal to the environment due to harmful Cr(VI). Long-time exposure to Cr(VI) imposes serious hazards on all living organisms. Hence, the treatment of tannery waste to remove Cr(VI) is not a choice but mandatory. Therefore, this study focused on the removal of Cr(VI) from the aqueous solutions via a teff (Eragrostis tef) straw based-activated carbon (TSAC) which was derived from locally available agricultural solid waste, teff straw (TS). The prepared TSAC was characterized using BET, FTIR, SEM, and XRD. A central composite approach-based RSM analysis was undertaken for statistical modeling and optimization for maximized Cr(VI) removal with respect to four important factors, namely, initial concentration of Cr(VI), the dosage of TSAC, pH, and adsorption time. Optimized values for maximizing adsorption of Cr(VI) (95% of removal) were acquired to be initial Cr(VI) concentration: 87.57 mg/L, TSAC dosage: 2.742 g/100 mL, pH: 2.2, and contact time:109 min. The results from the design of the experiment were also analyzed for the significance of the interaction between the selected process parameters. In addition, the pseudo-second-order kinetic and Langmuir isotherm models were found suitable for describing the adsorption data. The adsorption capacity of Cr(VI) on TSAC was 19.48 mg/g. The observed thermodynamic characteristics reveal that Cr(VI) adsorption on TASC is endothermic in nature. From the results, TSAC had shown a potential Cr(VI) efficiency on optimized process conditions that can be exploited effectively as adsorbent for removal of Cr(VI)-contaminated wastes.

/pdf/a-statistical-modeling-and-optimization-for-cr-vi-adsorption-30v6qam3.pdf

A Statistical Modeling and Optimization for Cr(VI) Adsorption from Aqueous Media via Teff Straw-Based Activated Carbon: Isotherm, Kinetics, and Thermodynamic Studies

Recently, rapid industrialization leads to excessive release of heavy metals such as Cr(VI) in the environment. Exposure to chromium (VI) can cause kidney and liver damage, depressed immune systems, and a variety of cancers. Therefore, treatment of Cr(VI) containing wastewater is mandatory. This study aims to optimize the removal of Cr(VI) from aqueous solution using locally available Teff husk activated carbon adsorbent. The laboratory-based study was conducted on the optimization of Cr(VI) removal efficiency of Teff husk activated carbon from aqueous solution. A central composite design was used to examine the effect of the interaction of process parameters and to optimize the process using Design Expert version 7.0 software. The optimized removal efficiency of Teff husk activated carbon (95.597%) was achieved at 1.92 pH, 87.83 mg/L initial concentration, 20.22 g/L adsorbent dose, and 2.07 H contact time. The adsorption of Cr(VI) on Teff husk activated carbon was found to be best fitted with pseudo-second-order kinetics and Langmuir isotherm model of the adsorption. Teff husk activated carbon can be used as an efficient adsorbent for removal of chromium (VI) from contaminated water. Column adsorption needs to be studied in the future.

/pdf/response-surface-methodology-as-a-statistical-tool-for-251uq63l8h.pdf

Response surface methodology as a statistical tool for optimization of removal of chromium (VI) from aqueous solution by Teff ( Eragrostis teff ) husk activated carbon

A liquid-solid circulating fluidized bed (LSCFB) helps to overcome the shortcomings of conventional fluidized beds by using a particle separation and return system as an integral part of the overall reactor configuration. Batch adsorption experiments were carried out for the removal of phenol from a synthetically prepared solution using fresh activated-carbon-coated glass beads. The morphological features and surface chemistry of the adsorbent were analyzed via SEM and FTIR techniques. The adsorbent dosage, contact time and temperature were varied along with solution pH to assess their effects on the adsorbent performance for phenol removal. Isotherm modeling showed that the phenol removal using the activated-carbon glass beads followed the Langmuir model. Effectively, it was observed at an adsorbent loading of 2.5 g/150 mL of feed volume and a contact time of 3 h produced an 80% efficiency in the batch study. Furthermore, on scaling it up to the column, the desired 98% phenol-removal efficiency was obtained with an adsorbent dosage of 250 g and contact time of 25 min. Adsorbent regeneration using 5% (v/v) ethanol showed a 64% desorption of phenol from the sorbent within 20 min in the LSCFB.

https://www.mdpi.com/1996-1073/13/15/3839/pdf

Continuous Phenol Removal Using a Liquid–Solid Circulating Fluidized Bed

https://figshare.com/articles/journal_contribution/Adsorption_Phenomenon_for_Removal_of_Pb_II_via_Teff_Straw_based_Activated_Carbon_Prepared_by_Microwave-Assisted_Pyrolysis_Process_Modelling_Statistical_Optimisation_Isotherm_Kinetics_and_Thermodynamic_Studies/18973003/1/files/33788263.pdf

Adsorption Phenomenon for Removal of Pb(II) via Teff Straw based Activated Carbon Prepared by Microwave-Assisted Pyrolysis: Process Modelling, Statistical Optimisation, Isotherm, Kinetics, and Thermodynamic Studies

Comparative adsorptive performance of adsorbents developed from sugar industrial wastes for the removal of melanoidin pigment from molasses distillery spent wash

Modeling of adsorption of Cr6+ on to activated carbon prepared from Sterculia foetida dried seed shells under different drying techniques namely sun, oven, and microwave drying (450W, 600W, 900W power). Optimization of process parameters such as pH, adsorbent dosage (g/ml), temperature (°C), contact time (min) were evaluated using Central Composite Rotatable Design (CCRD) of Response Surface Methodology (RSM). For batch adsorption studies at pH 3, adsorbent dosage of 1.5 g/ml, temperature 35°C and contact time 90 min were found to be optimum for the system under consideration and Microwave Activated Carbonized Sterculia foetida (MACSF) at 450W was found to be best suited for the adsorption of Cr+6 ions. The system was found to follow Langmuir type monolayer adsorption for the given operational parameters. SEM analysis was used to study the surface morphology of the carbon samples and the effect of pretreatment on carbonization.

https://iopscience.iop.org/article/10.1088/1757-899X/206/1/012065/pdf

N Gnanasundaram

Papers

Optimization and Performance parameters for adsorption of Cr6+ by microwave assisted carbon from Sterculia foetida shells