Nathan S. Lewis

Bio: Nathan S. Lewis is an academic researcher from California Institute of Technology. The author has contributed to research in topics: Semiconductor & Silicon. The author has an hindex of 112, co-authored 720 publications receiving 64808 citations. Previous affiliations of Nathan S. Lewis include Lawrence Berkeley National Laboratory & Massachusetts Institute of Technology.

Phosphine Functionalization of GaAs(111)A Surfaces

Abstract: Phosphorus-functionalized GaAs surfaces have been prepared by exposure of Cl-terminated GaAs(111)A surfaces to triethylphosphine (PEt3) or trichlorophosphine (PCl3), or by the direct functionalization of the native-oxide terminated GaAs(111)A surface with PCl3. The presence of phosphorus on each functionalized surface was confirmed by X-ray photoelectron spectroscopy. High-resolution, soft X-ray photoelectron spectroscopy was used to evaluate the As and Ga 3d regions of such surfaces. On PEt3 treated surfaces, the Ga 3d spectra exhibited a bulk Ga peak as well as peaks that were shifted to 0.35, 0.92 and 1.86 eV higher binding energy. These peaks were assigned to residual Cl-terminated Ga surface sites, surficial Ga2O and surficial Ga2O3, respectively. For PCl3-treated surfaces, the Ga 3d spectra displayed peaks ascribable to bulk Ga(As), Ga2O, and Ga2O3, as well as a peak shifted 0.30 eV to higher binding energy relative to the bulk signal. A peak corresponding to Ga(OH)3, observed on the Cl-terminated surface, was absent from all of the phosphine-functionalized surfaces. After reaction of the Cl-terminated GaAs(111)A surface with PCl3 or PEt3, the As 3d spectral region was free of As oxides and As0. Although native oxide-terminated GaAs surfaces were free of As oxides after reaction with PCl3, such surfaces contained detectable amounts of As0. Photoluminescence measurements indicted that phosphine-functionalized surfaces prepared from Cl-terminated GaAs(111)A surfaces had better electrical properties than the native-oxide capped GaAs(111)A surface, while the native-oxide covered surface treated with PCl3 showed no enhancement in PL intensity.

Solar fuels generator

Abstract: The solar fuels generator includes an ionically conductive separator between a gaseous first phase and a second phase. A photoanode uses one or more components of the first phase to generate cations during operation of the solar fuels generator. A cation conduit is positioned provides a pathway along which the cations travel from the photoanode to the separator. The separator conducts the cations. A second solid cation conduit conducts the cations from the separator to a photocathode.

Proton exchange membrane electrolysis using water vapor as a feedstock

Abstract: A light-driven electrolytic cell that uses water vapor as the feedstock and that has no wires or connections whatsoever to an external electrical power source of any kind. In one embodiment, the electrolytic cell uses a proton exchange membrane (PEM) with an IrRuOx water oxidation catalyst and a Pt black water reduction catalyst to consume water vapor and generate molecular oxygen and a chemical fuel, molecular hydrogen. The operation of the electrolytic cell using water vapor supplied by a humidified carrier gas has been demonstrated under varying conditions of the gas flow rate, the relative humidity, and the presence or absence of oxygen. The performance of the system with water vapor was also compared to the performance when the device was immersed in liquid water.

Analysis of time-resolved photocurrent transients at semiconductor/liquid interfaces

Abstract: Small signal photocurrent transients have been measured for n-Si/CH_3OH-Me_2Fc^(+/0)/Pt, n-Si/Au/CH_3OH-Me_2Fc^(+/0)/Pt, n-Si/Pt/NaOH(aq)/Ni(OH)_2/Ni, n-TiO_2/NaOH(aq)/Ni(OH)_2/Ni, and n-TiO_2/NaOH(aq)-Fe(CN)_6^(3-/4-)/Pt cells. Even though the radio-frequency and microwave conductivity signals for photoexcited n-Si/CH_3OH-Me_2Fc^(+/0) contacts persist for > 100 µs, the photocurrent transients for these interfaces decayed in <10 µs and were limited by the series resistance of the cell in combination with the space-charge capacitance of the semiconductor. An equivalent circuit model is presented and physically justified in order to explain this behavior. The model is also used to elucidate the conditions under which photocurrent transients at semiconductor electrodes can be expected to yield information regarding the faradaic charge-transfer rate across the semiconductor/liquid interface.

I and i

Abstract: There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality. Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

A low-cost, high-efficiency solar cell based on dye-sensitized colloidal TiO2 films

Abstract: THE large-scale use of photovoltaic devices for electricity generation is prohibitively expensive at present: generation from existing commercial devices costs about ten times more than conventional methods1. Here we describe a photovoltaic cell, created from low-to medium-purity materials through low-cost processes, which exhibits a commercially realistic energy-conversion efficiency. The device is based on a 10-µm-thick, optically transparent film of titanium dioxide particles a few nanometres in size, coated with a monolayer of a charge-transfer dye to sensitize the film for light harvesting. Because of the high surface area of the semiconductor film and the ideal spectral characteristics of the dye, the device harvests a high proportion of the incident solar energy flux (46%) and shows exceptionally high efficiencies for the conversion of incident photons to electrical current (more than 80%). The overall light-to-electric energy conversion yield is 7.1-7.9% in simulated solar light and 12% in diffuse daylight. The large current densities (greater than 12 mA cm-2) and exceptional stability (sustaining at least five million turnovers without decomposition), as well as the low cost, make practical applications feasible.

疟原虫var基因转换速率变化导致抗原变异[英]／Paul H, Robert P, Christodoulou Z, et al//Proc Natl Acad Sci U S A

Abstract: 抗原变异可使得多种致病微生物易于逃避宿主免疫应答。表达在感染红细胞表面的恶性疟原虫红细胞表面蛋白1（PfPMP1）与感染红细胞、内皮细胞、树突状细胞以及胎盘的单个或多个受体作用，在黏附及免疫逃避中起关键的作用。每个单倍体基因组var基因家族编码约60种成员，通过启动转录不同的var基因变异体为抗原变异提供了分子基础。

Heterogeneous photocatalyst materials for water splitting

Abstract: This critical review shows the basis of photocatalytic water splitting and experimental points, and surveys heterogeneous photocatalyst materials for water splitting into H2 and O2, and H2 or O2 evolution from an aqueous solution containing a sacrificial reagent Many oxides consisting of metal cations with d0 and d10 configurations, metal (oxy)sulfide and metal (oxy)nitride photocatalysts have been reported, especially during the latest decade The fruitful photocatalyst library gives important information on factors affecting photocatalytic performances and design of new materials Photocatalytic water splitting and H2 evolution using abundant compounds as electron donors are expected to contribute to construction of a clean and simple system for solar hydrogen production, and a solution of global energy and environmental issues in the future (361 references)