Ned Mohan

Bio: Ned Mohan is an academic researcher from University of Minnesota. The author has contributed to research in topics: Power factor & Transformer. The author has an hindex of 57, co-authored 356 publications receiving 17286 citations. Previous affiliations of Ned Mohan include Unisys & University of Canterbury.

Power Electronics: Converters, Applications and Design

Abstract: Partial table of contents: Overview of Power Semiconductor Switches Computer Simulation of Power Electronic Converters and Systems GENERIC POWER ELECTRONIC CIRCUITS dc--dc Switch-Mode Converters Resonant Converters: Zero-Voltage and/or Zero-Current Switchings POWER SUPPLY APPLICATIONS Power Conditioners and Uninterruptible Power Supplies MOTOR DRIVE APPLICATIONS dc Motor Drives Induction Motor Drives Synchronous Motor Drives OTHER APPLICATIONS Residential and Industrial Applications Optimizing the Utility Interface with Power Electronic Systems SEMICONDUCTOR DEVICES Basic Semiconductor Physics Power Diodes Power MOSFETs Thyristors Emerging Devices and Circuits PRACTICAL CONVERTER DESIGN CONSIDERATIONS Snubber Circuits Gate and Base Drive Circuits Design of Magnetic Components Index

Design and implementation of an extended Kalman filter for the state estimation of a permanent magnet synchronous motor

Abstract: Practical considerations for implementing the discrete extended Kalman filter in real time with a digital signal processor are discussed. The system considered is a permanent magnet synchronous motor (PMSM) without a position sensor, and the extended Kalman filter is designed for the online estimation of the speed and rotor position by only using measurements of the motor voltages and currents. The algorithms developed to allow efficient computation of the filter are presented. The computational techniques used to simplify the filter equations and their implementation in fixed-point arithmetic are discussed. Simulation and experimental results are presented to demonstrate the feasibility of this estimation process. >

Three-Port Series-Resonant DC–DC Converter to Interface Renewable Energy Sources With Bidirectional Load and Energy Storage Ports

Abstract: In this paper, a three-port converter with three active full bridges, two series-resonant tanks, and a three-winding transformer is proposed. It uses a single power conversion stage with high-frequency link to control power flow between batteries, load, and a renewable source such as fuel cell. The converter has capabilities of bidirectional power flow in the battery and the load port. Use of series-resonance aids in high switching frequency operation with realizable component values when compared to existing three-port converter with only inductors. The converter has high efficiency due to soft-switching operation in all three bridges. Steady-state analysis of the converter is presented to determine the power flow equations, tank currents, and soft-switching region. Dynamic analysis is performed to design a closed-loop controller that will regulate the load-side port voltage and source-side port current. Design procedure for the three-port converter is explained and experimental results of a laboratory prototype are presented.

Control of a Doubly Fed Induction Wind Generator Under Unbalanced Grid Voltage Conditions

Abstract: Wind energy is often installed in rural, remote areas characterized by weak, unbalanced power transmission grids. In induction wind generators, unbalanced three-phase stator voltages cause a number of problems, such as overcurrent, unbalanced currents, reactive power pulsations, and stress on the mechanical components from torque pulsations. Therefore, beyond a certain amount of unbalance, induction wind generators are switched out of the network. This can further weaken the grid. In doubly fed induction generators (DFIGs), control of the rotor currents allows for adjustable speed operation and reactive power control. This paper presents a DFIG control strategy that enhances the standard speed and reactive power control with controllers that can compensate for the problems caused by an unbalanced grid by balancing the stator currents and eliminating torque and reactive power pulsations

Active input-voltage and load-current sharing in input-series and output-parallel connected modular DC-DC converters using dynamic input-voltage reference scheme

Abstract: This paper explores a new configuration for modular DC/DC converters, namely, series connection at the input, and parallel connection at the output, such that the converters share the input voltage and load current equally. This is an important step toward realizing a truly modular power system architecture, where low-power, low-voltage, building block modules can be connected in any series/parallel combination at input or at output, to realize any given system specifications. A three-loop control scheme, consisting of a common output voltage loop, individual inner current loops, and individual input voltage loops, is proposed to achieve input voltage and load current sharing. The output voltage loop provides the basic reference for inner current loops, which is modified by the respective input voltage loops. The average of converter input voltages, which is dynamically varying, is chosen as the reference for input voltage loops. This choice of reference eliminates interaction among different control loops. The input-series and output-parallel (ISOP) configuration is analyzed using the incremental negative resistance model of DC/DC converters. Based on the analysis, design methods for input voltage controller are developed. Analysis and proposed design methods are verified through simulation, and experimentally, on an ISOP system consisting of two forward converters.

I and i

Abstract: There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality. Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

Z-source inverter

Abstract: This paper presents an impedance-source (or impedance-fed) power converter (abbreviated as Z-source converter) and its control method for implementing DC-to-AC, AC-to-DC, AC-to-AC, and DC-to-DC power conversion. The Z-source converter employs a unique impedance network (or circuit) to couple the converter main circuit to the power source, thus providing unique features that cannot be obtained in the traditional voltage-source (or voltage-fed) and current-source (or current-fed) converters where a capacitor and inductor are used, respectively. The Z-source converter overcomes the conceptual and theoretical barriers and limitations of the traditional voltage-source converter (abbreviated as V-source converter) and current-source converter (abbreviated as I-source converter) and provides a novel power conversion concept. The Z-source concept can be applied to all DC-to-AC, AC-to-DC, AC-to-AC, and DC-to-DC power conversion. To describe the operating principle and control, this paper focuses on an example: a Z-source inverter for DC-AC power conversion needed in fuel cell applications. Simulation and experimental results are presented to demonstrate the new features.

Overview of current development in electrical energy storage technologies and the application potential in power system operation

Abstract: Electrical power generation is changing dramatically across the world because of the need to reduce greenhouse gas emissions and to introduce mixed energy sources. The power network faces great challenges in transmission and distribution to meet demand with unpredictable daily and seasonal variations. Electrical Energy Storage (EES) is recognized as underpinning technologies to have great potential in meeting these challenges, whereby energy is stored in a certain state, according to the technology used, and is converted to electrical energy when needed. However, the wide variety of options and complex characteristic matrices make it difficult to appraise a specific EES technology for a particular application. This paper intends to mitigate this problem by providing a comprehensive and clear picture of the state-of-the-art technologies available, and where they would be suited for integration into a power generation and distribution system. The paper starts with an overview of the operation principles, technical and economic performance features and the current research and development of important EES technologies, sorted into six main categories based on the types of energy stored. Following this, a comprehensive comparison and an application potential analysis of the reviewed technologies are presented.

A review of active filters for power quality improvement

Abstract: Active filtering of electric power has now become a mature technology for harmonic and reactive power compensation in two-wire (single phase), three-wire (three phase without neutral), and four-wire (three phase with neutral) AC power networks with nonlinear loads. This paper presents a comprehensive review of active filter (AF) configurations, control strategies, selection of components, other related economic and technical considerations, and their selection for specific applications. It is aimed at providing a broad perspective on the status of AF technology to researchers and application engineers dealing with power quality issues. A list of more than 200 research publications on the subject is also appended for a quick reference.

Power electronics as efficient interface in dispersed power generation systems

Abstract: The global electrical energy consumption is rising and there is a steady increase of the demand on the power capacity, efficient production, distribution and utilization of energy. The traditional power systems are changing globally, a large number of dispersed generation (DG) units, including both renewable and nonrenewable energy sources such as wind turbines, photovoltaic (PV) generators, fuel cells, small hydro, wave generators, and gas/steam powered combined heat and power stations, are being integrated into power systems at the distribution level. Power electronics, the technology of efficiently processing electric power, play an essential part in the integration of the dispersed generation units for good efficiency and high performance of the power systems. This paper reviews the applications of power electronics in the integration of DG units, in particular, wind power, fuel cells and PV generators.