In this chapter, we will restrict our attention to the ferrites and a few other closely related materials. The great interest in ferrites stems from their unique combination of a spontaneous magnetization and a high electrical resistivity. The observed magnetization results from the difference in the magnetizations of two non-equivalent sub-lattices of the magnetic ions in the crystal structure. Materials of this type should strictly be designated as “ferrimagnetic” and in some respects are more closely related to anti-ferromagnetic substances than they are to ferromagnetics in which the magnetization results from the parallel alignment of all the magnetic moments present. We shall not adhere to this special nomenclature except to emphasize effects, which are due to the existence of the sub-lattices.

Ferromagnetic materials

The field of power harvesting has experienced significant growth over the past few years due to the ever-increasing desire to produce portable and wireless electronics with extended lifespans. Current portable and wireless devices must be designed to include electrochemical batteries as the power source. The use of batteries can be troublesome due to their limited lifespan, thus necessitating their periodic replacement. In the case of wireless sensors that are to be placed in remote locations, the sensor must be easily accessible or of a disposable nature to allow the device to function over extended periods of time. Energy scavenging devices are designed to capture the ambient energy surrounding the electronics and convert it into usable electrical energy. The concept of power harvesting works towards developing self-powered devices that do not require replaceable power supplies. A number of sources of harvestable ambient energy exist, including waste heat, vibration, electromagnetic waves, wind, flowing water, and solar energy. While each of these sources of energy can be effectively used to power remote sensors, the structural and biological communities have placed an emphasis on scavenging vibrational energy with piezoelectric materials. This article will review recent literature in the field of power harvesting and present the current state of power harvesting in its drive to create completely self-powered devices.

/pdf/a-review-of-power-harvesting-using-piezoelectric-materials-k69swwfj1u.pdf

A review of power harvesting using piezoelectric materials (2003–2006)

/pdf/micro-total-analysis-systems-1-introduction-theory-and-27f7corp18.pdf

Micro Total Analysis Systems. 1. Introduction, Theory, and Technology

We survey progress over the past 25 years in the development of microscale devices for pumping fluids. We attempt to provide both a reference for micropump researchers and a resource for those outside the field who wish to identify the best micropump for a particular application. Reciprocating displacement micropumps have been the subject of extensive research in both academia and the private sector and have been produced with a wide range of actuators, valve configurations and materials. Aperiodic displacement micropumps based on mechanisms such as localized phase change have been shown to be suitable for specialized applications. Electroosmotic micropumps exhibit favorable scaling and are promising for a variety of applications requiring high flow rates and pressures. Dynamic micropumps based on electrohydrodynamic and magnetohydrodynamic effects have also been developed. Much progress has been made, but with micropumps suitable for important applications still not available, this remains a fertile area for future research.

https://microfluidics.stanford.edu/Publications/Micropumps_Cooling/Laser%20Review%20of%20Micropumps%20in%20JMM.pdf

A review of micropumps

This tutorial/survey paper: (1) provides a concise point of departure for researchers and practitioners alike wishing to assess the current state of the art in the control and monitoring of civil engineering structures; and (2) provides a link between structural control and other fields of control theory, pointing out both differences and similarities, and points out where future research and application efforts are likely to prove fruitful. The paper consists of the following sections: section 1 is an introduction; section 2 deals with passive energy dissipation; section 3 deals with active control; section 4 deals with hybrid and semiactive control systems; section 5 discusses sensors for structural control; section 6 deals with smart material systems; section 7 deals with health monitoring and damage detection; and section 8 deals with research needs. An extensive list of references is provided in the references section.

Structural control: past, present, and future

Damping of structural vibrations with piezoelectric materials and passive electrical networks

The paper models the effects of dynamic coupling between a structure and an electrical network through the piezoelectric effect. The coupled equations of motion of an arbitrary elastic structure with piezoelectric elements and passive electronics are derived. State space models are developed for three important cases: direct voltage driven electrodes, direct charge driven electrodes, and an indirect drive case where the piezoelec tric electrodes are connected to an arbitrary electrical circuit with embedded voltage and current sources. The equations are applied to the case of a cantilevered beam with surface mounted piezoceramics and indirect voltage and current drive. The theoretical derivations are validated experimentally on an actively controlled cantilevered beam test article with indirect voltage drive.

Modelling of Piezoelectric Actuator Dynamics for Active Structural Control

Piezoelectric Fiber Composites were previously introduced as an alternative to monolithic piezoceramic wafers for structural actuation applications. This manuscript was an investigation into the improvement of piezoelectric fiber composite performance through a nonconventional electroding scheme. Two microelectromechanical models were developed that predict the composite properties. These models were used to examine the trends of composite properties versus fiber volume fraction for various constituent materials. Several etched electrode PZT fiber composites, with fiber volume fractions ranging from 7% to 58%, were manufactured and tested. Experimental measurements showed excellent agreement with both the trends and magnitude of model predicted values. The maximum fiber volume fraction composites demonstrated a capacitance (E3 /Eo) of 550, piezoelectric free strain constants (d33 and d31) of 150 pm/V and-70 pm/V, and piezoelectric clamped stress (e33) of 5 C/m2, showing a substantial improvement over prev...

Piezoelectric Fiber Composites with Interdigitated Electrodes

A piezoelectric rotary ultrasonic motor is modeled for the purpose of predicting, a priori, motor performance as a function of design parameters. The Rayleigh-Ritz assumed mode energy method is used to model the distributed piezoceramics and the traveling wave dynamics of the stator. Natural frequencies and modeshapes are obtained for a generally configured motor. Nonlinear normal and tangential interface forces between the rotor and stator are incorporated into the forcing function along with the linear piezoelectric forcing. Given the applied torque, applied axial loading, and piezo drive voltages as inputs to the model, general motor performance measures are obtained-namely speed, input power, output power, and efficiency. The approach presented here provides a general framework for modeling these motors as well as a design tool for optimizing prototypes with the added flexibility of allowing for a wide variety of geometries and materials. >

Modeling of a piezoelectric rotary ultrasonic motor

An investigation was made into the field of planar structural actuation with anisotropic active materials. The mechanisms for creating anisotropic actuators were discussed, and the impact of anisot...

Nesbitt W. Hagood

Papers

Damping of structural vibrations with piezoelectric materials and passive electrical networks

Modelling of Piezoelectric Actuator Dynamics for Active Structural Control

Piezoelectric Fiber Composites with Interdigitated Electrodes

Modeling of a piezoelectric rotary ultrasonic motor

Anisotropic actuation with piezoelectric fiber composites