Synthetic Aperture Radar (SAR) has been widely used for Earth remote sensing for more than 30 years. It provides high-resolution, day-and-night and weather-independent images for a multitude of applications ranging from geoscience and climate change research, environmental and Earth system monitoring, 2-D and 3-D mapping, change detection, 4-D mapping (space and time), security-related applications up to planetary exploration. With the advances in radar technology and geo/bio-physical parameter inversion modeling in the 90s, using data from several airborne and spaceborne systems, a paradigm shift occurred from the development driven by the technology push to the user demand pull. Today, more than 15 spaceborne SAR systems are being operated for innumerous applications. This paper provides first a tutorial about the SAR principles and theory, followed by an overview of established techniques like polarimetry, interferometry and differential interferometry as well as of emerging techniques (e.g., polarimetric SAR interferometry, tomography and holographic tomography). Several application examples including the associated parameter inversion modeling are provided for each case. The paper also describes innovative technologies and concepts like digital beamforming, Multiple-Input Multiple-Output (MIMO) and bi- and multi-static configurations which are suitable means to fulfill the increasing user requirements. The paper concludes with a vision for SAR remote sensing.

/pdf/a-tutorial-on-synthetic-aperture-radar-1v8k9pqokm.pdf

A tutorial on synthetic aperture radar

TanDEM-X (TerraSAR-X add-on for digital elevation measurements) is an innovative spaceborne radar interferometer that is based on two TerraSAR-X radar satellites flying in close formation. The primary objective of the TanDEM-X mission is the generation of a consistent global digital elevation model (DEM) with an unprecedented accuracy, which is equaling or surpassing the HRTI-3 specification. Beyond that, TanDEM-X provides a highly reconfigurable platform for the demonstration of new radar imaging techniques and applications. This paper gives a detailed overview of the TanDEM-X mission concept which is based on the systematic combination of several innovative technologies. The key elements are the bistatic data acquisition employing an innovative phase synchronization link, a novel satellite formation flying concept allowing for the collection of bistatic data with short along-track baselines, as well as the use of new interferometric modes for system verification and DEM calibration. The interferometric performance is analyzed in detail, taking into account the peculiarities of the bistatic operation. Based on this analysis, an optimized DEM data acquisition plan is derived which employs the combination of multiple data takes with different baselines. Finally, a collection of instructive examples illustrates the capabilities of TanDEM-X for the development and demonstration of new remote sensing applications.

/pdf/tandem-x-a-satellite-formation-for-high-resolution-sar-z54xhync6a.pdf

TanDEM-X: A Satellite Formation for High-Resolution SAR Interferometry

Digital Coding of Waveforms

http://ieeexplore.ieee.org/iel5/4768668/4784008/04784017.pdf

TanDEM-X: A satellite formation for high-resolution SAR interferometry

Antenna Theory And Design

The displaced phase center (DPC) technique will enable a wide-swath synthetic aperture radar (SAR) with high azimuth resolution. In a classic DPC system, the pulse repetition frequency (PRF) has to be chosen such that the SAR carrier moves just one half of its antenna length between subsequent radar pulses. Any deviation from this PRF will result in a nonuniform sampling of the synthetic aperture. This letter derives an innovative reconstruction algorithm and shows that an unambiguous reconstruction of a SAR signal is possible for nonuniform sampling of the synthetic aperture. This algorithm will also have great potential for multistatic satellite constellations as well as the dual receive antenna mode in Radarsat 2 and TerraSAR-X.

/pdf/unambiguous-sar-signal-reconstruction-from-nonuniform-4o45f9hb8k.pdf

Unambiguous SAR signal reconstruction from nonuniform displaced phase center sampling

This paper introduces the innovative concept of multidimensional waveform encoding for spaceborne synthetic aperture radar (SAR). The combination of this technique with digital beamforming on receive enables a new generation of SAR systems with improved performance and flexible imaging capabilities. Examples are high-resolution wide-swath radar imaging with compact antennas, enhanced sensitivity for applications like alongtrack interferometry and moving object indication, and the implementation of hybrid SAR imaging modes that are well suited to satisfy hitherto incompatible user requirements. Implementation-specific issues are discussed and performance examples demonstrate the potential of the new technique for different remote sensing applications.

/pdf/multidimensional-waveform-encoding-a-new-digital-beamforming-4n7bbrmqpq.pdf

Multidimensional Waveform Encoding: A New Digital Beamforming Technique for Synthetic Aperture Radar Remote Sensing

Synthetic Aperture Radar (SAR) is a well-proven imaging technique for remote sensing of the Earth. However, conventional SAR systems are not capable of fulfilling the increasing demands for improved spatial resolution and wider swath coverage. To overcome these inherent limitations, several innovative techniques have been suggested which employ multiple receive-apertures to gather additional information along the synthetic aperture. These digital beamforming (DBF) on receive techniques are reviewed with particular emphasis on the multi-aperture signal processing in azimuth and a multi-aperture reconstruction algorithm is presented that allows for the unambiguous recovery of the Doppler spectrum. The impact of Doppler aliasing is investigated and an analytic expression for the residual azimuth ambiguities is derived. Further, the influence of the processing on the signal-to-noise ratio (SNR) is analyzed, resulting in a pulse repetition frequency (PRF) dependent factor describing the SNR scaling of the multi-aperture beamforming network. The focus is then turned to a complete high-resolution wide-swath SAR system design example which demonstrates the intricate connection between multi-aperture azimuth processing and the system architecture. In this regard, alternative processing approaches are compared with the multi-aperture reconstruction algorithm. In a next step, optimization strategies are discussed as pattern tapering, prebeamshaping-on-receive, and modified processing algorithms. In this context, the analytic expressions for both the residual ambiguities and the SNR scaling factor are generalized to cascaded beamforming networks. The suggested techniques can moreover be extended in many ways. Examples discussed are a combination with ScanSAR burst mode operation and the transfer to multistatic sparse array configurations.

/pdf/errata-digital-beamforming-on-receive-techniques-and-3qhoy471zp.pdf

Errata: Digital Beamforming on Receive: Techniques and Optimization Strategies for High-Resolution Wide-Swath SAR Imaging

Due to a system-inherent limitation, conventional synthetic aperture radar (SAR) is incapable of imaging a wide swath with high geometric resolution. This restriction can be overcome by systems with multiple receive channels in combination with an additional digital signal processing network. So far, the application of such digital beamforming algorithms for high-resolution wide-swath SAR imaging has been restricted to multichannel systems in stripmap operation. However, in stripmap mode, the overall azimuth antenna length restricts the achievable swath width, thus preventing very wide swaths as requested by future SAR missions. Consequently, new concepts for ultrawide-swath imaging are needed. A promising candidate is a SAR system with multiple azimuth channels being operated in burst mode. This paper analyzes innovative ScanSAR and Terrain Observation by Progressive Scans (TOPS) system concepts with regard to multichannel azimuth processing. For this, the theoretical analyses, performance figures, and SAR signal processing, which had previously been derived for multichannel stripmap mode, are extended to systems operating in burst modes. The investigations reveal that multichannel ScanSAR systems enable the imaging of ultrawide swaths with high azimuth resolution and compact antenna lengths. These considerations are embedded in a multichannel ScanSAR system design example to demonstrate its capability to image an ultrawide swath of 400 km with a high geometric resolution of 5 m. In a next step, this system is adapted to TOPS mode operation, including an innovative “staircase” multichannel processing approach optimized for TOPS.

/pdf/multichannel-azimuth-processing-in-scansar-and-tops-mode-2aigvqrm2a.pdf

Multichannel Azimuth Processing in ScanSAR and TOPS Mode Operation

This paper reviews advanced multi-channel SAR system concepts for the imaging of ultra-wide swaths with high azimuth resolution. Novel system architectures and operational modes are introduced and compared to each other with regard to their performance.

/pdf/advanced-concepts-for-ultra-wide-swath-sar-imaging-5fkq2ew4ek.pdf

Nicolas Gebert

Papers

Unambiguous SAR signal reconstruction from nonuniform displaced phase center sampling

Multidimensional Waveform Encoding: A New Digital Beamforming Technique for Synthetic Aperture Radar Remote Sensing

Errata: Digital Beamforming on Receive: Techniques and Optimization Strategies for High-Resolution Wide-Swath SAR Imaging

Multichannel Azimuth Processing in ScanSAR and TOPS Mode Operation

Advanced Concepts for Ultra-Wide-Swath SAR Imaging