Nouari Saheb

Bio: Nouari Saheb is an academic researcher from King Fahd University of Petroleum and Minerals. The author has contributed to research in topics: Spark plasma sintering & Sintering. The author has an hindex of 17, co-authored 60 publications receiving 951 citations.

Spark plasma sintering of metals and metal matrix nanocomposites: a review

Abstract: Metal matrix nanocomposites (MMNCs) are thosemetal matrix composites where the reinforcement is of nanometer dimensions, typically less than 100nm in size. Also, it is possible to have both the matrix and reinforcement phases of nanometer dimensions. The improvement in mechanical properties of MMNCs is attributed to the size and strength of the reinforcement as well as to the fine grain size of the matrix. Spark plasma sintering has been used extensively over the past years to consolidate wide range of materials including nanocomposites and was shown to be effective noneconventional sintering method for obtaining fully dense materials with preserved nanostructure features. The objective of this work is to briefly present the spark plasma sintering process and review published work on spark-plasma-sintered metals and metal matrix nanocomposites.

Spark plasma and microwave sintering of Al6061 and Al2124 alloys

Abstract: Despite the importance of aluminum alloys as candidate materials for applications in aerospace and automotive industries, very little work has been published on spark plasma and microwave processing of aluminum alloys. In the present work, the possibility was explored to process Al2124 and Al6061 alloys by spark plasma and microwave sintering techniques, and the microstructures and properties were compared. The alloys were sintered for 20 min at 400, 450, and 500°C. It is found that compared to microwave sintering, spark plasma sintering is an effective way to obtain homogenous, dense, and hard alloys. Fully dense (100%) Al6061 and Al2124 alloys were obtained by spark plasma sintering for 20 min at 450 and 500°C, respectively. Maximum relative densities were achieved for Al6061 (92.52%) and Al2124 (93.52%) alloys by microwave sintering at 500°C for 20 min. The Vickers microhardness of spark plasma sintered samples increases with the increase of sintering temperature from 400 to 500°C, and reaches the values of Hv 70.16 and Hv 117.10 for Al6061 and Al2124 alloys, respectively. For microwave sintered samples, the microhardness increases with the increase of sintering temperature from 400 to 450°C, and then decreases with the further increase of sintering temperature to 500°C.

Fiber-Embedded Metallic Materials: From Sensing towards Nervous Behavior

Abstract: Embedding of fibers in materials has attracted serious attention from researchers and has become a new research trend. Such material structures are usually termed “smart” or more recently “nervous”. Materials can have the capability of sensing and responding to the surrounding environmental stimulus, in the former, and the capability of feeling multiple structural and external stimuli, while feeding information back to a controller for appropriate real-time action, in the latter. In this paper, embeddable fibers, embedding processes, and behavior of fiber-embedded metallic materials are reviewed. Particular emphasis has been given to embedding fiber Bragg grating (FBG) array sensors and piezo wires, because of their high potential to be used in nervous materials for structural health monitoring. Ultrasonic consolidation and laser-based layered manufacturing processes are discussed in detail because of their high potential to integrate fibers without disruption. In addition, current challenges associated with embedding fibers in metallic materials are highlighted and recommendations for future research work are set.

I and i

Abstract: There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality. Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

Recent progress in the development and properties of novel metal matrix nanocomposites reinforced with carbon nanotubes and graphene nanosheets

Abstract: One-dimensional carbon nanotubes and two-dimensional graphene nanosheets with unique electrical, mechanical and thermal properties are attractive reinforcements for fabricating light weight, high strength and high performance metal-matrix composites. Rapid advances of nanotechnology in recent years enable the development of advanced metal matrix nanocomposites for structural engineering and functional device applications. This review focuses on the recent development in the synthesis, property characterization and application of aluminum, magnesium, and transition metal-based composites reinforced with carbon nanotubes and graphene nanosheets. These include processing strategies of carbonaceous nanomaterials and their composites, mechanical and tribological responses, corrosion, electrical and thermal properties as well as hydrogen storage and electrocatalytic behaviors. The effects of nanomaterial dispersion in the metal matrix and the formation of interfacial precipitates on these properties are also addressed. Particular attention is paid to the fundamentals and the structure–property relationships of such novel nanocomposites.

Aluminium matrix hybrid composites: a review of reinforcement philosophies; mechanical, corrosion and tribological characteristics

Abstract: Aluminium hybrid composites are a new generation of metal matrix composites that have the potentials of satisfying the recent demands of advanced engineering applications. These demands are met due to improved mechanical properties, amenability to conventional processing technique and possibility of reducing production cost of aluminium hybrid composites. The performance of these materials is mostly dependent on selecting the right combination of reinforcing materials since some of the processing parameters are associated with the reinforcing particulates. A few combinations of reinforcing particulates have been conceptualized in the design of aluminium hybrid composites. This paper attempts to review the different combination of reinforcing materials used in the processing of hybrid aluminium matrix composites and how it affects the mechanical, corrosion and wear performance of the materials. The major techniques for fabricating these materials are briefly discussed and research areas for further improvement on aluminium hybrid composites are suggested.

Microwave–material interaction phenomena: Heating mechanisms, challenges and opportunities in material processing

Abstract: Efforts to use microwaves in material processing are gradually increasing. However, the phenomena associated with the processing are less understood; popular mechanisms such as dipolar heating and conduction heating have been mostly explored. The current paper reviews most of the significant phenomena that cause heating during microwave–material interaction and heat transfer during microwave energy absorption in materials. Mechanisms involved during interaction of microwave with characteristically different materials – metals, non-metals and composites (metal matrix composites, ceramic matrix composites and polymer matrix composites) have been discussed using suitable illustrations. It was observed that while microwave heating of metal based materials is due to the magnetic field based loss effects, dipolar loss and conduction loss are the phenomena associated with the electric field effects in microwave heating of non-metals. Challenges in processing of advanced materials, particularly composites have been identified from the available literature; further research directions with possible benefits have been highlighted.