P. Cruise

Bio: P. Cruise is an academic researcher from Texas Instruments. The author has contributed to research in topics: CMOS & GSM. The author has an hindex of 10, co-authored 15 publications receiving 1321 citations.

All-digital PLL and transmitter for mobile phones

Abstract: We present the first all-digital PLL and polar transmitter for mobile phones. They are part of a single-chip GSM/EDGE transceiver SoC fabricated in a 90 nm digital CMOS process. The circuits are architectured from the ground up to be compatible with digital deep-submicron CMOS processes and be readily integrateable with a digital baseband and application processor. To achieve this, we exploit the new paradigm of a deep-submicron CMOS process environment by leveraging on the fast switching times of MOS transistors, the fine lithography and the precise device matching, while avoiding problems related to the limited voltage headroom. The transmitter architecture is fully digital and utilizes the wideband direct frequency modulation capability of the all-digital PLL. The amplitude modulation is realized digitally by regulating the number of active NMOS transistor switches in accordance with the instantaneous amplitude. The conventional RF frequency synthesizer architecture, based on a voltage-controlled oscillator and phase/frequency detector and charge-pump combination, has been replaced with a digitally controlled oscillator and a time-to-digital converter. The transmitter performs GMSK modulation with less than 0.5/spl deg/ rms phase error, -165 dBc/Hz phase noise at 20 MHz offset, and 10 /spl mu/s settling time. The 8-PSK EDGE spectral mask is met with 1.2% EVM. The transmitter occupies 1.5 mm/sup 2/ and consumes 42 mA at 1.2 V supply while producing 6 dBm RF output power.

All-digital PLL and GSM/EDGE transmitter in 90nm CMOS

Abstract: A 1.2V 42mA all-digital PLL and polar transmitter for a single-chip GSM/EDGE transceiver is implemented in 90nm CMOS. It transmits GMSK with 0.5/spl deg/ rms phase error and achieves -165dBc/Hz phase noise at 20MHz offset, with 10 /spl mu/s settling time. A digitally controlled 6dBm class-E PA modulates the amplitude and meets the EDGE spectral mask with 3.5% EVM.

The First Fully Integrated Quad-Band GSM/GPRS Receiver in a 90-nm Digital CMOS Process

Abstract: We present the receiver in the first single-chip GSM/GPRS transceiver that incorporates full integration of quad-band receiver, transmitter, memory, power management, dedicated ARM processor and RF built-in self test in a 90-nm digital CMOS process. The architecture uses Nyquist rate direct RF sampling in the receiver and an all-digital phase-locked loop (PLL) for generating the local oscillator (LO). The receive chain uses discrete-time analog signal processing to down-convert, down-sample, filter and analog-to-digital convert the received signal. A feedback loop is provided at the mixer output and can be used to cancel DC-offsets as well to study linearization of the receive chain. The receiver meets a sensitivity of -110 dBm at 60mA in a 1.4-V digital CMOS process in the presence of more than one million digital gates

A digital-to-RF-amplitude converter for GSM/GPRS/EDGE in 90-nm digital CMOS

Abstract: We present the first 90-nm digital CMOS RF power amplifier. This PA contains a large array of NMOS switches, and performs a direct digital-to-RF-amplitude conversion, filtering and buffering in a fully-integrated GSM/EDGE transmitter. Power control is fully digital. 40% efficiency is obtained at 10-dBm output power from 1.4 V and it occupies 0.005 mm/sup 2/.

A 24mm 2 Quad-Band Single-Chip GSM Radio with Transmitter Calibration in 90nm Digital CMOS

Abstract: The RF transceiver is built on the Digital RF Processor (DRP) technology The ADPLL-based transmitter uses a polar architecture with all-digital PM-FM and AM paths The receiver uses a discrete-time architecture in which the RF signal is directly sampled and processed using analog and DSP techniques A 26 MHz digitally controlled crystal oscillator (DCXO) generates frequency reference (FREF) and has a means of high-frequency dithering to minimize the effects of coupling from digitally controlled PA driver (DPA) to DCXO by de-sensitizing its slicing buffer

All-digital PLL and transmitter for mobile phones

Abstract: We present the first all-digital PLL and polar transmitter for mobile phones. They are part of a single-chip GSM/EDGE transceiver SoC fabricated in a 90 nm digital CMOS process. The circuits are architectured from the ground up to be compatible with digital deep-submicron CMOS processes and be readily integrateable with a digital baseband and application processor. To achieve this, we exploit the new paradigm of a deep-submicron CMOS process environment by leveraging on the fast switching times of MOS transistors, the fine lithography and the precise device matching, while avoiding problems related to the limited voltage headroom. The transmitter architecture is fully digital and utilizes the wideband direct frequency modulation capability of the all-digital PLL. The amplitude modulation is realized digitally by regulating the number of active NMOS transistor switches in accordance with the instantaneous amplitude. The conventional RF frequency synthesizer architecture, based on a voltage-controlled oscillator and phase/frequency detector and charge-pump combination, has been replaced with a digitally controlled oscillator and a time-to-digital converter. The transmitter performs GMSK modulation with less than 0.5/spl deg/ rms phase error, -165 dBc/Hz phase noise at 20 MHz offset, and 10 /spl mu/s settling time. The 8-PSK EDGE spectral mask is met with 1.2% EVM. The transmitter occupies 1.5 mm/sup 2/ and consumes 42 mA at 1.2 V supply while producing 6 dBm RF output power.

The Path to the Software-Defined Radio Receiver

Abstract: After being the subject of speculation for many years, a software-defined radio receiver concept has emerged that is suitable for mobile handsets. A key step forward is the realization that in mobile handsets, it is enough to receive one channel with any bandwidth, situated in any band. Thus, the front-end can be tuned electronically. Taking a cue from a digital front-end, the receiver's flexible analog baseband samples the channel of interest at zero IF, and is followed by clock-programmable downsampling with embedded filtering. This gives a tunable selectivity that exceeds that of an RF prefilter, and a conversion rate that is low enough for A/D conversion at only milliwatts. The front-end consists of a wideband low noise amplifier and a mixer tunable by a wideband LO. A 90-nm CMOS prototype tunes 200 kHz to 20-MHz-wide channels located anywhere from 800 MHz to 6 GHz

An 800-MHz–6-GHz Software-Defined Wireless Receiver in 90-nm CMOS

Abstract: A software-defined radio receiver is designed from a low-power ADC perspective, exploiting programmability of windowed integration sampler and clock-programmable discrete-time analog filters. To cover the major frequency bands in use today, a wideband RF front-end, including the low-noise amplifier (LNA) and a wide tuning-range synthesizer, spanning over 800 MHz to 6 GHz is designed. The wideband LNA provides 18-20 dB of maximum gain and 3-3.5 dB of noise figure over 800 MHz to 6 GHz. A low 1/f noise and high-linearity mixer is designed which utilizes the passive mixer core properties and provides around +70 dBm IIP2 over the bandwidth of operation. The entire receiver circuits are implemented in 90-nm CMOS technology. Programmability of the receiver is tested for GSM and 802.11g standards

1.3 V 20 ps time-to-digital converter for frequency synthesis in 90-nm CMOS

Abstract: We propose and demonstrate a 20-ps time-to-digital converter (TDC) realized in 90-nm digital CMOS. It is used as a phase/frequency detector and charge pump replacement in an all-digital phase-locked loop for a fully-compliant Global System for Mobile Communications (GSM) transceiver. The TDC core is based on a pseudodifferential digital architecture that makes it insensitive to nMOS and pMOS transistor mismatches. The time conversion resolution is equal to an inverter propagation delay, which is the finest logic-level regenerative timing in CMOS. The TDC is self calibrating with the estimation accuracy better than 1%. It additionally serves as a CMOS process strength estimator for analog circuits in this large system-on-chip. Measured integral nonlinearity is 0.7 least significant bits. The TDC consumes 5.3 mA raw and 1.3 mA with power management from a 1.3-V supply.

A Highly Linear Broadband CMOS LNA Employing Noise and Distortion Cancellation

Abstract: A broadband inductorless low-noise amplifier (LNA) design that utilizes simultaneous noise and distortion cancellation is presented. Concurrent cancellation of the intrinsic third-order distortion from individual stages is exhibited with the common-gate and common-source cascade. The LNA is then limited by the second-order interaction between the common source and common gate stages, which is common in all cascade amplifiers. Further removal of this third-order distortion is achieved by incorporating a second-order-distortion-free circuit technique in the common gate stage. Implemented in 0.13 m CMOS technology, this LNA achieved 16 dBm in both the 900 MHz and 2 GHz bands. Measurements demonstrate that the LNA has a minimum internal gain of 14.5 dB, noise figure of 2.6 dB from 800 MHz to 2.1GHz while drawing 11.6 mA from 1.5 V supply voltage.