Parag Bhargava

Bio: Parag Bhargava is an academic researcher from Indian Institute of Technology Bombay. The author has contributed to research in topics: Dye-sensitized solar cell & Auxiliary electrode. The author has an hindex of 30, co-authored 168 publications receiving 2521 citations. Previous affiliations of Parag Bhargava include University of Alabama at Birmingham & Indian Institute of Technology Kharagpur.

A Simple Direct Casting Route to Ceramic Foams

Abstract: A simple direct foaming and casting process using ovalbumin-based aqueous slurries for fabricating ceramic and metal foams is demonstrated. Foaming of aqueous ceramic slurries and the foam microstructure were seen to be a strong function of slurry rheology. Setting of foams with ceramic solids loading above 20 vol% was achieved by addition of acid, which also prevented binder migration. Acid addition resulted in excessive shrinkage, causing cracking of foams with ceramic loading below 20 vol%. Addition of sucrose to the slurries suppressed shrinkage leading to defect-free foams with porosity exceeding 95%. Overall porosity and foam microstructure could be controlled through ceramic solids loading, ovalbumin–water ratio, foaming time and sucrose amount, and sintering temperature. The ceramic foams fabricated by the process were strong enough to be green machined to different shapes.

Dye Sensitized Solar Cells: A Review

Abstract: The development of dye sensitized solar cells (DSSCs), which have derived inspiration from photosynthesis, has opened up exciting new possibilities and paradigms for producing solar photovoltaics possibly at lower cost. The dye-sensitized solar cells with moderate power conversion (∼10%) efficiencies can be manufactured under regular lab conditions without needing clean rooms or very specialized facilities. The entire processing need not involve even a single vapour deposition step. The DSSCs can be considered to be electrochemical devices consisting of (a) a photoanode which has a thick film of a wide band gap oxide semiconductor (like TiO2), typically coated on a transparent conductive oxide (TCO) glass substrate, with TiO2 being sensitized with adsorbed dyes that absorb visible light, (b) an electrolyte that establishes the internal electrical continuity between anode and counter electrode and mainly plays the role of regenerating the dye such that the photoexcitation, electron injection and current fl...

Composition dependent optical, structural and photoluminescence characteristics of cesium tin halide perovskites

Abstract: In this article we report the structural and optical properties of varying compositions of lead free inorganic perovskite (CsSnX3 (X = Br, Cl, I)) and its tunable photoluminescence covering the entire visible to near-IR region. Optical band gap studies for prepared inorganic cesium tin halide compositions show a significant (53.5%) blue shift in the absorption spectra as the halide composition varies from I to Br and Cl. As the halide composition was varied from Cl to I, an intense and tunable PL emission was observed at room temperature covering a wide range from Vis-near IR region (420–950 nm). X-ray diffraction studies revealed that undoped compositions were orthorhombic (CsSnI3), cubic (CsSnBr3) and monoclinic (CsSnCl3) in structure at room temperature. For mixed halides, the lattice constant was found to increase gradually as the size of halide cation increases from Cl− to Br− and I−.

Chemical Synthesis, Characterization, and Biocompatibility Study of Hydroxyapatite/Chitosan Phosphate Nanocomposite for Bone Tissue Engineering Applications

Abstract: A novel bioanalogue hydroxyapatite (HAp)/chitosan phosphate (CSP) nanocomposite has been synthesized by a solution-based chemical methodology with varying HAp contents from 10 to 60% (w/w). The interfacial bonding interaction between HAp and CSP has been investigated through Fourier transform infrared absorption spectra (FTIR) and x-ray diffraction (XRD). The surface morphology of the composite and the homogeneous dispersion of nanoparticles in the polymer matrix have been investigated through scanning electron microscopy (SEM) and transmission electron microscopy (TEM), respectively. The mechanical properties of the composite are found to be improved significantly with increase in nanoparticle contents. Cytotoxicity test using murine L929 fibroblast confirms that the nanocomposite is cytocompatible. Primary murine osteoblast cell culture study proves that the nanocomposite is osteocompatible and highly in vitro osteogenic. The use of CSP promotes the homogeneous distribution of particles in the polymer matrix through its pendant phosphate groups along with particle-polymer interfacial interactions. The prepared HAp/CSP nanocomposite with uniform microstructure may be used in bone tissue engineering applications.

Egg White as an Environmentally Friendly Low-Cost Binder for Gelcasting of Ceramics

Abstract: Slurries with different solids loading (34–50 vol%) of alumina were made with egg white (ovalbumin)–water premix. The ovalbumin content in the premix was decreased with increase in solids loading to lower slurry viscosity. The slurries were cast into bulk shapes and heated to 80°C, resulting in denaturation of ovalbumin forming a gel. The gelled samples were dried under controlled humidity and sintered in air to densities 94%–97% of theoretical. Alumina slurries formed with egg white (no water) were used to form tapes as thin as 60 μm in the sintered state.

Processing Routes to Macroporous Ceramics: A Review

Abstract: Macroporous ceramics with pore sizes from 400 nm to 4 mm and porosity within the range 20%–97% have been produced for a number of well-established and emerging applications, such as molten metal filtration, catalysis, refractory insulation, and hot gas filtration. These applications take advantage of the unique properties achieved through the incorporation of macropores into solid ceramics. In this article, we review the main processing routes that can be used for the fabrication of macroporous ceramics with tailored microstructure and chemical composition. Emphasis is given to versatile and simple approaches that allow one to control the microstructural features that ultimately determine the properties of the macroporous material. Replica, sacrificial template, and direct foaming techniques are described and compared in terms of microstructures and mechanical properties that can be achieved. Finally, directions to future investigations on the processing of macroporous ceramics are proposed.

3D printing of ceramics: A review

Abstract: Along with extensive research on the three-dimensional (3D) printing of polymers and metals, 3D printing of ceramics is now the latest trend to come under the spotlight. The ability to fabricate ceramic components of arbitrarily complex shapes has been extremely challenging without 3D printing. This review focuses on the latest advances in the 3D printing of ceramics and presents the historical origins and evolution of each related technique. The main technical aspects, including feedstock properties, process control, post-treatments and energy source–material interactions, are also discussed. The technical challenges and advice about how to address these are presented. Comparisons are made between the techniques to facilitate the selection of the best ones in practical use. In addition, representative applications of the 3D printing of various types of ceramics are surveyed. Future directions are pointed out on the advancement on materials and forming mechanism for the fabrication of high-performance ceramic components.

Advanced Organic Chemistry

Abstract: Organic Chemistry By Dr. I. L. Finar. Vol. 2: Stereochemistry and the Chemistry of Natural Products. Pp. xi + 733. (London and New York: Longmans, Green and Co., Ltd., 1956.) 40s. net.

Nanostructured high-strength molybdenum alloys with unprecedented tensile ductility

Abstract: The high-temperature stability and mechanical properties of refractory molybdenum alloys are highly desirable for a wide range of critical applications. However, a long-standing problem for these alloys is that they suffer from low ductility and limited formability. Here we report a nanostructuring strategy that achieves Mo alloys with yield strength over 800 MPa and tensile elongation as large as ~ 40% at room temperature. The processing route involves a molecular-level liquid-liquid mixing/doping technique that leads to an optimal microstructure of submicrometre grains with nanometric oxide particles uniformly distributed in the grain interior. Our approach can be readily adapted to large-scale industrial production of ductile Mo alloys that can be extensively processed and shaped at low temperatures. The architecture engineered into such multicomponent alloys offers a general pathway for manufacturing dispersion-strengthened materials with both high strength and ductility.

Calcium Phosphate Bioceramics: A Review of Their History, Structure, Properties, Coating Technologies and Biomedical Applications.

Abstract: Calcium phosphate (CaP) bioceramics are widely used in the field of bone regeneration, both in orthopedics and in dentistry, due to their good biocompatibility, osseointegration and osteoconduction. The aim of this article is to review the history, structure, properties and clinical applications of these materials, whether they are in the form of bone cements, paste, scaffolds, or coatings. Major analytical techniques for characterization of CaPs, in vitro and in vivo tests, and the requirements of the US Food and Drug Administration (FDA) and international standards from CaP coatings on orthopedic and dental endosseous implants, are also summarized, along with the possible effect of sterilization on these materials. CaP coating technologies are summarized, with a focus on electrochemical processes. Theories on the formation of transient precursor phases in biomineralization, the dissolution and reprecipitation as bone of CaPs are discussed. A wide variety of CaPs are presented, from the individual phases to nano-CaP, biphasic and triphasic CaP formulations, composite CaP coatings and cements, functionally graded materials (FGMs), and antibacterial CaPs. We conclude by foreseeing the future of CaPs.