Peter J. Uggowitzer

Bio: Peter J. Uggowitzer is an academic researcher from University of Leoben. The author has contributed to research in topics: Alloy & Microstructure. The author has an hindex of 57, co-authored 338 publications receiving 11393 citations. Previous affiliations of Peter J. Uggowitzer include Biotronik & École Polytechnique Fédérale de Lausanne.

MgZnCa glasses without clinically observable hydrogen evolution for biodegradable implants

Abstract: Corrosion is normally an undesirable phenomenon in engineering applications. In the field of biomedical applications, however, implants that 'biocorrode' are of considerable interest. Deploying them not only abrogates the need for implant-removal surgery, but also circumvents the long-term negative effects of permanent implants. In this context magnesium is an attractive biodegradable material, but its corrosion is accompanied by hydrogen evolution, which is problematic in many biomedical applications. Whereas the degradation and thus the hydrogen evolution of crystalline Mg alloys can be altered only within a very limited range, Mg-based glasses offer extended solubility for alloying elements plus a homogeneous single-phase structure, both of which may alter corrosion behaviour significantly. Here we report on a distinct reduction in hydrogen evolution in Zn-rich MgZnCa glasses. Above a particular Zn-alloying threshold (approximately 28 at.%), a Zn- and oxygen-rich passivating layer forms on the alloy surface, which we explain by a model based on the calculated Pourbaix diagram of Zn in simulated body fluid. We document animal studies that confirm the great reduction in hydrogen evolution and reveal the same good tissue compatibility as seen for crystalline Mg implants. Thus, the glassy Mg(60+x)Zn(35-x)Ca5 (0 < or = x < or = 7) alloys show great potential for deployment in a new generation of biodegradable implants.

Mechanical anisotropy of extruded Mg-6% Al-1% Zn alloy

Abstract: Deformation anisotropy of extruded Mg–6% Al–1% Zn alloy has been investigated on specimens with different tilt angles relative to the extrusion direction. Calculations of the orientation factors for basal slip and of the strains caused by {1 0 1 2} twinning were done for a slightly idealised texture. This quantification of the two dominating deformation modes was used to explain the marked mechanical anisotropy of the extruded magnesium alloy. Basal slip as well as {1 0 1 2} twinning is inhibited in extrusion direction under tensile loads, which results in high yield strength. Any other testing direction and/or compressive loads are capable of activating slip and/or twinning and yield stress is significantly lower under such conditions. The lattice reorientation of 86.3° caused by twinning has a large influence on the deformation behaviour of a pre-deformed specimen, since the twinned areas are capable of untwinning during reloading in the opposite direction.

Alternative Plasmonic Materials: Beyond Gold and Silver

Abstract: Materials research plays a vital role in transforming breakthrough scientific ideas into next-generation technology. Similar to the way silicon revolutionized the microelectronics industry, the proper materials can greatly impact the field of plasmonics and metamaterials. Currently, research in plasmonics and metamaterials lacks good material building blocks in order to realize useful devices. Such devices suffer from many drawbacks arising from the undesirable properties of their material building blocks, especially metals. There are many materials, other than conventional metallic components such as gold and silver, that exhibit metallic properties and provide advantages in device performance, design flexibility, fabrication, integration, and tunability. This review explores different material classes for plasmonic and metamaterial applications, such as conventional semiconductors, transparent conducting oxides, perovskite oxides, metal nitrides, silicides, germanides, and 2D materials such as graphene. This review provides a summary of the recent developments in the search for better plasmonic materials and an outlook of further research directions.

Bone Tissue Engineering: Recent Advances and Challenges

Abstract: The worldwide incidence of bone disorders and conditions has trended steeply upward and is expected to double by 2020, especially in populations where aging is coupled with increased obesity and poor physical activity. Engineered bone tissue has been viewed as a potential alternative to the conventional use of bone grafts, due to their limitless supply and no disease transmission. However, bone tissue engineering practices have not proceeded to clinical practice due to several limitations or challenges. Bone tissue engineering aims to induce new functional bone regeneration via the synergistic combination of biomaterials, cells, and factor therapy. In this review, we discuss the fundamentals of bone tissue engineering, highlighting the current state of this field. Further, we review the recent advances of biomaterial and cell-based research, as well as approaches used to enhance bone regeneration. Specifically, we discuss widely investigated biomaterial scaffolds, micro- and nano-structural properties of these scaffolds, and the incorporation of biomimetic properties and/or growth factors. In addition, we examine various cellular approaches, including the use of mesenchymal stem cells (MSCs), embryonic stem cells (ESCs), adult stem cells, induced pluripotent stem cells (iPSCs), and platelet-rich plasma (PRP), and their clinical application strengths and limitations. We conclude by overviewing the challenges that face the bone tissue engineering field, such as the lack of sufficient vascularization at the defect site, and the research aimed at functional bone tissue engineering. These challenges will drive future research in the field.

Recent developments in stainless steels

Abstract: This article presents an overview of the developments in stainless steels made since the 1990s. Some of the new applications that involve the use of stainless steel are also introduced. A brief introduction to the various classes of stainless steels, their precipitate phases and the status quo of their production around the globe is given first. The advances in a variety of subject areas that have been made recently will then be presented. These recent advances include (1) new findings on the various precipitate phases (the new J phase, new orientation relationships, new phase diagram for the Fe–Cr system, etc.); (2) new suggestions for the prevention/mitigation of the different problems and new methods for their detection/measurement and (3) new techniques for surface/bulk property enhancement (such as laser shot peening, grain boundary engineering and grain refinement). Recent developments in topics like phase prediction, stacking fault energy, superplasticity, metadynamic recrystallisation and the calculation of mechanical properties are introduced, too. In the end of this article, several new applications that involve the use of stainless steels are presented. Some of these are the use of austenitic stainless steels for signature authentication (magnetic recording), the utilisation of the cryogenic magnetic transition of the sigma phase for hot spot detection (the Sigmaplugs), the new Pt-enhanced radiopaque stainless steel (PERSS) coronary stents and stainless steel stents that may be used for magnetic drug targeting. Besides recent developments in conventional stainless steels, those in the high-nitrogen, low-Ni (or Ni-free) varieties are also introduced. These recent developments include new methods for attaining very high nitrogen contents, new guidelines for alloy design, the merits/demerits associated with high nitrogen contents, etc.