Peter Krulevitch

Bio: Peter Krulevitch is an academic researcher from Lawrence Livermore National Laboratory. The author has contributed to research in topics: Electrical conduit & Surface micromachining. The author has an hindex of 26, co-authored 80 publications receiving 2829 citations. Previous affiliations of Peter Krulevitch include University of California & Cordis.

Thin film shape memory alloy microactuators

Abstract: Thin film shape memory alloys (SMAs) have the potential to become a primary actuating mechanism for mechanical devices with dimensions in the micron-to-millimeter range requiring large forces over long displacements. The work output per volume of thin film SMA microactuators exceeds that of other microactuation mechanisms such as electrostatic, magnetic, thermal bimorph, piezoelectric, and thermopneumatic, and it is possible to achieve cycling frequencies on the order of 100 Hz due to the rapid heat transfer rates associated with thin film devices. In this paper, a quantitative comparison of several microactuation schemes is made, techniques for depositing and characterizing Ni-Ti-based shape memory films are evaluated, and micromachining and design issues for SMA microactuators are discussed. The substrate curvature method is used to investigate the thermo-mechanical properties of Ni-Ti-Cu SMA films, revealing recoverable stresses up to 510 MPa, transformation temperatures above 32/spl deg/C, and hysteresis widths between 5 and 13/spl deg/C. Fatigue data shows that for small strains, applied loads up to 350 MPa can be sustained for thousands of cycles. Two micromachined shape memory-actuated devices-a microgripper and microvalve-also are presented.

Microdevices in medicine.

Abstract: The application of microelectromechanical systems (MEMS) to medicine is described. Three types of biomedical devices are considered, including diagnostic microsystems, surgical microsystems, and therapeutic microsystems. The opportunities of MEMS miniaturization in these emerging disciplines are considered, with emphasis placed on the importance of the technology in providing a better outcome for the patient and a lower overall health care cost. Several case examples in each of these areas are described. Key aspects of MEMS technology as it is applied to these three areas are described, along with some of the fabrication challenges.

Release mechanism utilizing shape memory polymer material

Abstract: Microfabricated therapeutic actuators are fabricated using a shape memory polymer (SMP), a polyurethane-based material that undergoes a phase transformation at a specified temperature (Tg). At a temperature above temperature Tg material is soft and can be easily reshaped into another configuration. As the temperature is lowered below temperature Tg the new shape is fixed and locked in as long as the material stays below temperature Tg. Upon reheating the material to a temperature above Tg, the material will return to its original shape. By the use of such SMP material, SMP microtubing can be used as a release actuator for the delivery of embolic coils through catheters into aneurysms, for example. The microtubing can be manufactured in various sizes and the phase change temperature Tg is determinate for an intended temperature target and intended use.

Flexible electrode array for artificial vision

Abstract: An image is captured or otherwise converted into a signal in an artificial vision system. The signal is transmitted to the retina utilizing an implant. The implant consists of a polymer substrate made of a compliant material such as poly(dimethylsiloxane) or PDMS. The polymer substrate is conformable to the shape of the retina. Electrodes and conductive leads are embedded in the polymer substrate. The conductive leads and the electrodes transmit the signal representing the image to the cells in the retina. The signal representing the image stimulates cells in the retina.

Serpentine and corduroy circuits to enhance the stretchablity of a stretchable electronic device

Abstract: A stretchable electronic apparatus and method of producing the apparatus. The apparatus has a central longitudinal axis and the apparatus is stretchable in a longitudinal direction generally aligned with the central longitudinal axis. The apparatus comprises a stretchable polymer body, and at least one circuit line operatively connected to the stretchable polymer body, the at least one circuit line extending in the longitudinal direction and having a longitudinal component that extends in the longitudinal direction and having an offset component that is at an angle to the longitudinal direction, the longitudinal component and the offset component allowing the apparatus to stretch in the longitudinal direction while maintaining the integrity of the at least one circuit line.

Microfluidic large scale integration

Abstract: High-density microfluidic chips contain plumbing networks with thousands of micromechanical valves and hundreds of individually addressable chambers. These fluidic devices are analogous to electronic integrated circuits fabricated using large scale integration (LSI). A component of these networks is the fluidic multiplexor, which is a combinatorial array of binary valve patterns that exponentially increases the processing power of a network by allowing complex fluid manipulations with a minimal number of inputs. These integrated microfluidic networks can be used to construct a variety of highly complex microfluidic devices, for example the microfluidic analog of a comparator array, and a microfluidic memory storage device resembling electronic random access memories.

A nanoscale optical biosensor: sensitivity and selectivity of an approach based on the localized surface plasmon resonance spectroscopy of triangular silver nanoparticles.

Abstract: Triangular silver nanoparticles (∼100 nm wide and 50 nm high) have remarkable optical properties. In particular, the peak extinction wavelength, λmax of their localized surface plasmon resonance (LSPR) spectrum is unexpectedly sensitive to nanoparticle size, shape, and local (∼10−30 nm) external dielectric environment. This sensitivity of the LSPR λmax to the nanoenvironment has allowed us to develop a new class of nanoscale affinity biosensors. The essential characteristics and operational principles of these LSPR nanobiosensors will be illustrated using the well-studied biotin−streptavidin system. Exposure of biotin-functionalized Ag nanotriangles to 100 nM streptavidin (SA) caused a 27.0 nm red-shift in the LSPR λmax. The LSPR λmax shift, ΔR/ΔRmax, versus [SA] response curve was measured over the concentration range 10-15 M < [SA] < 10-6 M. Comparison of the data with the theoretical normalized response expected for 1:1 binding of a ligand to a multivalent receptor with different sites but invariant af...

Physics and applications of microfluidics in biology.

Abstract: ■ Abstract Fluid flow at the microscale exhibits unique phenomena that can be leveraged to fabricate devices and components capable of performing functions useful for biological studies. The physics of importance to microfluidics are reviewed. Common methods of fabricating microfluidic devices and systems are described. Components, including valves, mixers, and pumps, capable of controlling fluid flow by utilizing the physics of the microscale are presented. Techniques for sensing flow characteristics are described and examples of devices and systems that perform bioanalysis are presented. The focus of this review is microscale phenomena and the use of the physics of the scale to create devices and systems that provide functionality useful to the life sciences.

Stretchable form of single crystal silicon for high performance electronics on rubber substrates

Abstract: The present invention provides stretchable, and optionally printable, semiconductors and electronic circuits capable of providing good performance when stretched, compressed, flexed or otherwise deformed. Stretchable semiconductors and electronic circuits of the present invention preferred for some applications are flexible, in addition to being stretchable, and thus are capable of significant elongation, flexing, bending or other deformation along one or more axes. Further, stretchable semiconductors and electronic circuits of the present invention may be adapted to a wide range of device configurations to provide fully flexible electronic and optoelectronic devices.