R. L. Boivin

Bio: R. L. Boivin is an academic researcher from General Atomics. The author has contributed to research in topics: Alcator C-Mod & Divertor. The author has an hindex of 28, co-authored 95 publications receiving 3414 citations.

First results from Alcator‐C‐MOD*

Abstract: Early operation of the Alcator‐C‐MOD tokamak [I.H. Hutchinson, Proceedings of IEEE 13th Symposium on Fusion Engineering, Knoxville, TN, edited by M. Lubell, M. Nestor, and S. Vaughan (Institute of Electrical and Electronic Engineers, New York, 1990), Vol. 1, p. 13] is surveyed. Reliable operation, with plasma current up to 1 MA, has been obtained, despite the massive conducting superstructure and the associated error fields. However, vertical disruptions are not slowed by the long vessel time constant. With pellet fueling, peak densities up to 9×1020 m−3 have been attained and ‘‘snakes’’ are often seen. Initial characterization of divertor and scrape‐off layer is presented and indicates approximately Bohm diffusion. The edge plasma shows a wealth of marfe‐like phenomena, including a transition to detachment from the divertor plates with accompanying radiative divertor regions. Energy confinement generally appears to exceed the expectations of neo‐Alcator scaling. A transition to Ohmic H mode has been observed. Ion cyclotron heating experiments have demonstrated good power coupling, in agreement with theory.

Chapter 7: Diagnostics

Abstract: In order to support the operation of ITER and the planned experimental programme an extensive set of plasma and first wall measurements will be required. The number and type of required measurements will be similar to those made on the present-day large tokamaks while the specification of the measurements—time and spatial resolutions, etc—will in some cases be more stringent. Many of the measurements will be used in the real time control of the plasma driving a requirement for very high reliability in the systems (diagnostics) that provide the measurements. The implementation of diagnostic systems on ITER is a substantial challenge. Because of the harsh environment (high levels of neutron and gamma fluxes, neutron heating, particle bombardment) diagnostic system selection and design has to cope with a range of phenomena not previously encountered in diagnostic design. Extensive design and R&D is needed to prepare the systems. In some cases the environmental difficulties are so severe that new diagnostic techniques are required. a Author to whom any correspondence should be addressed.

Particle transport in the scrape-off layer and its relationship to discharge density limit in Alcator C-Mod

Abstract: Cross-field particle transport in the scrape-off layer (SOL) of Alcator C-Mod [Phys. Plasmas 1, 1511 (1994)] can be characterized by an effective particle diffusivity (Deff) that increases markedly with distance from the separatrix. As a consequence, recycling onto the main-chamber walls is large compared to plasma flows into the divertor volume. The SOL exhibits a two-layer structure: Steep gradients and moderate fluctuation levels are typically found in a ∼5 mm region near the separatrix (near SOL) where parallel electron conduction typically dominates energy losses. Small gradients and larger fluctuation levels with longer correlation times are found outside this region (far SOL). Deff in the near SOL increases strongly with local plasma collisionality normalized to the magnetic connection length. As the discharge density limit is approached, Deff and associated fluctuation levels become large across the entire SOL and cross-field heat convection everywhere exceeds parallel conduction losses, impacting the power balance of the discharge.

First tests of molybdenum mirrors for ITER diagnostics in DIII-D divertor

Abstract: Metallic mirrors will be used in ITER for optical diagnostics working in different spectral ranges. Their optical properties will change with time due to erosion, deposition, and particle implantation. First tests of molybdenum mirrors were performed in the DIII-D divertor under deposition-dominated conditions. Two sets of mirrors recessed 2cm below the divertor floor in the private flux region were exposed to a series of identical, lower-single-null, ELMing (featuring edge localized modes) H-mode discharges with detached plasma conditions in both divertor legs. The first set of mirrors was exposed at ambient temperature, while the second set was preheated to temperatures between 140 and 80°C. During the exposures mirrors in both sets were additionally heated by radiation from the plasma. The nonheated mirrors exhibited net carbon deposition at a rate of up to 3.7nm∕s and suffered a significant drop in reflectivity. Net carbon deposition rate on the preheated mirrors was a factor of 30–100 lower and their...

H mode confinement in Alcator C-Mod

Abstract: A series of experiments, examining the confinement properties of ion cyclotron range of frequencies (ICRF) heated H mode plasmas, has been carried out on the Alcator C-Mod tokamak. Alcator C-Mod is a compact tokamak that operates at high particle, power and current densities at toroidal fields up to 8 T. Under these conditions the plasma is essentially thermal with very little contribution to the stored energy from energetic ions (typically no more than 5%) and with Ti~Te. Most of the data were taken with the machine in a single null `closed' divertor configuration with the plasma facing components clad in molybdenum tiles. The data include those taken both before and after the first wall surfaces were coated with boron, with emphasis on the latter. H modes obtained from plasmas run on boronized walls typically had a lower impurity content and radiated power and attained a higher stored energy than those run on bare molybdenum. Confinement enhancement, the energy confinement time normalized to L mode scaling, for discharges with boronized walls, ranged from 1.6 to 2.4. The unique operating regime of the Alcator C-Mod device provided a means for extending the tests of global scaling laws to parameter ranges not previously accessible. For example, the Alcator C-Mod edge localized mode (ELM)-free data were found to be 1.1 to 1.6 times the ITERH93 scaling and the ELMy data almost 2.0 to 2.8 times the ITERH92 ELMy scaling law, suggesting that the size scaling in both scalings may be too strong. While both ELM-free and ELMy discharges were produced, the ELM characteristics were not easily compared with observations on other devices. No large, low frequency ELMs were seen despite the very high edge pressure and temperature gradients that were attained. For all of our H mode discharges, a clear linear relationship between the edge temperature pedestal and the temperature gradient in the core plasma was observed; the discharges with the `best' transport barriers also showing the greatest improvement in core c

Plasma{material interactions in current tokamaks and their implications for next step fusion reactors

Abstract: The major increase in discharge duration and plasma energy in a next step DT fusion reactor will give rise to important plasma-material effects that will critically influence its operation, safety and performance. Erosion will increase to a scale of several centimetres from being barely measurable at a micron scale in today's tokamaks. Tritium co-deposited with carbon will strongly affect the operation of machines with carbon plasma facing components. Controlling plasma-wall interactions is critical to achieving high performance in present day tokamaks, and this is likely to continue to be the case in the approach to practical fusion reactors. Recognition of the important consequences of these phenomena stimulated an internationally co-ordinated effort in the field of plasma-surface interactions supporting the Engineering Design Activities of the International Thermonuclear Experimental Reactor project (ITER), and significant progress has been made in better understanding these issues. The paper reviews the underlying physical processes and the existing experimental database of plasma-material interactions both in tokamaks and laboratory simulation facilities for conditions of direct relevance to next step fusion reactors. Two main topical groups of interaction are considered: (i) erosion/redeposition from plasma sputtering and disruptions, including dust and flake generation and (ii) tritium retention and removal. The use of modelling tools to interpret the experimental results and make projections for conditions expected in future devices is explained. Outstanding technical issues and specific recommendations on potential R&D avenues for their resolution are presented.

Chapter 1: Overview and summary

Abstract: The ITER Physics Basis presents and evaluates the physics rules and methodologies for plasma performance projections, which provide the basis for the design of a tokamak burning plasma device whose goal is to demonstrate the scientific and technological feasibility of fusion energy for peaceful purposes. This Chapter summarizes the physics basis for burning plasma projections, which is developed in detail by the ITER Physics Expert Groups in subsequent chapters. To set context, the design guidelines and requirements established in the report of ITER Special Working Group 1 are presented, as are the specifics of the tokamak design developed in the Final Design Report of the ITER Engineering Design Activities, which exemplifies burning tokamak plasma experiments. The behaviour of a tokamak plasma is determined by the interaction of many diverse physics processes, all of which bear on projections for both a burning plasma experiment and an eventual tokamak reactor. Key processes summarized here are energy and particle confinement and the H-mode power threshold; MHD stability, including pressure and density limits, neoclassical islands, error fields, disruptions, sawteeth, and ELMs; power and particle exhaust, involving divertor power dispersal, helium exhaust, fuelling and density control, H-mode edge transition region, erosion of plasma facing components, tritium retention; energetic particle physics; auxiliary power physics; and the physics of plasma diagnostics. Summaries of projection methodologies, together with estimates of their attendant uncertainties, are presented in each of these areas. Since each physics element has its own scaling properties, an integrated experimental demonstration of the balance between the combined processes which obtains in a reactor plasma is inaccessible to contemporary experimental facilities: it requires a reactor scale device. It is argued, moreover, that a burning plasma experiment can be sufficiently flexible to permit operation in a steady state mode, with non-inductive plasma current drive, as well as in a pulsed mode where current is inductively driven. Overall, the ITER Physics Basis can support a range of candidate designs for a tokamak burning plasma facility. For each design, there will remain a significant uncertainty in the projected performance, but the projection methodologies outlined here do suffice to specify the major parameters of such a facility and form the basis for assuring that its phased operation will return sufficient information to design a prototype commercial fusion power reactor, thus fulfilling the goal of the ITER project.

Chapter 4: Power and particle control

Abstract: Progress, since the ITER Physics Basis publication (ITER Physics Basis Editors et al 1999 Nucl. Fusion 39 2137–2664), in understanding the processes that will determine the properties of the plasma edge and its interaction with material elements in ITER is described. Experimental areas where significant progress has taken place are energy transport in the scrape-off layer (SOL) in particular of the anomalous transport scaling, particle transport in the SOL that plays a major role in the interaction of diverted plasmas with the main-chamber material elements, edge localized mode (ELM) energy deposition on material elements and the transport mechanism for the ELM energy from the main plasma to the plasma facing components, the physics of plasma detachment and neutral dynamics including the edge density profile structure and the control of plasma particle content and He removal, the erosion of low- and high-Z materials in fusion devices, their transport to the core plasma and their migration at the plasma edge including the formation of mixed materials, the processes determining the size and location of the retention of tritium in fusion devices and methods to remove it and the processes determining the efficiency of the various fuelling methods as well as their development towards the ITER requirements. This experimental progress has been accompanied by the development of modelling tools for the physical processes at the edge plasma and plasma–materials interaction and the further validation of these models by comparing their predictions with the new experimental results. Progress in the modelling development and validation has been mostly concentrated in the following areas: refinement in the predictions for ITER with plasma edge modelling codes by inclusion of detailed geometrical features of the divertor and the introduction of physical effects, which can play a major role in determining the divertor parameters at the divertor for ITER conditions such as hydrogen radiation transport and neutral–neutral collisions, modelling of the ion orbits at the plasma edge, which can play a role in determining power deposition at the divertor target, models for plasma–materials and plasma dynamics interaction during ELMs and disruptions, models for the transport of impurities at the plasma edge to describe the core contamination by impurities and the migration of eroded materials at the edge plasma and its associated tritium retention and models for the turbulent processes that determine the anomalous transport of energy and particles across the SOL. The implications for the expected performance of the reference regimes in ITER, the operation of the ITER device and the lifetime of the plasma facing materials are discussed.

Edge localized modes (ELMs)

Abstract: The phenomenology of edge localized modes (ELMs), an MHD instability occurring in the edge of H-mode plasmas in toroidal magnetic fusion experiments, is described. ELMs are important to obtain experimental control of the particle inventory of fusion plasmas. From an analysis of the ELM behaviour of different magnetic fusion experiments, three distinct types are identified, namely dithering cycles, type III and type I ELMs. A physical picture of these phenomena is established on the grounds of theoretical models put forward to describe the different ELM phenomena.

About these proceedings

Abstract: Mes premiers remtrciements trout aux auteurs des 206 communications th6matiquts et notes de projet, sans qui ces actes n'auraient 6videmment pas vu le jour. / Is oat contribu6 h la qualit6 scientifique et ,5 I'hmuog6t~6it6 pr6sentationntlle de leurs articles en refondant les versions iuitiales soumises an comit6 de programme, ea acceptant de suivre les r~gles de pr6sentation indiqu6es, et en nous envoyant parrots plusieurs versions am61ior6es surun point ou sur l'autrc.