Progress in the production and modification of PVDF membranes

In this review, the structural, mechanical, thermal, and chemical properties of substrates used for gallium nitride (GaN) epitaxy are compiled, and the properties of GaN films deposited on these substrates are reviewed. Among semiconductors, GaN is unique; most of its applications uses thin GaN films deposited on foreign substrates (materials other than GaN); that is, heteroepitaxial thin films. As a consequence of heteroepitaxy, the quality of the GaN films is very dependent on the properties of the substrate—both the inherent properties such as lattice constants and thermal expansion coefficients, and process induced properties such as surface roughness, step height and terrace width, and wetting behavior. The consequences of heteroepitaxy are discussed, including the crystallographic orientation and polarity, surface morphology, and inherent and thermally induced stress in the GaN films. Defects such as threading dislocations, inversion domains, and the unintentional incorporation of impurities into the epitaxial GaN layer resulting from heteroepitaxy are presented along with their effect on device processing and performance. A summary of the structure and lattice constants for many semiconductors, metals, metal nitrides, and oxides used or considered for GaN epitaxy is presented. The properties, synthesis, advantages and disadvantages of the six most commonly employed substrates (sapphire, 6H-SiC, Si, GaAs, LiGaO 2 , and AlN) are presented. Useful substrate properties such as lattice constants, defect densities, elastic moduli, thermal expansion coefficients, thermal conductivities, etching characteristics, and reactivities under deposition conditions are presented. Efforts to reduce the defect densities and to optimize the electrical and optical properties of the GaN epitaxial film by substrate etching, nitridation, and slight misorientation from the (0 0 0 1) crystal plane are reviewed. The requirements, the obstacles, and the results to date to produce zincblende GaN on 3C-SiC/Si(0 0 1) and GaAs are discussed. Tables summarizing measures of the GaN quality such as XRD rocking curve FWHM, photoluminescence peak position and FWHM, and electron mobilities for GaN epitaxial layers produced by MOCVD, MBE, and HVPE for each substrate are given. The initial results using GaN substrates, prepared as bulk crystals and as free-standing epitaxial films, are reviewed. Finally, the promise and the directions of research on new potential substrates, such as compliant and porous substrates are described.

Substrates for gallium nitride epitaxy

Piezoresistive sensors are among the earliest micromachined silicon devices. The need for smaller, less expensive, higher performance sensors helped drive early micromachining technology, a precursor to microsystems or microelectromechanical systems (MEMS). The effect of stress on doped silicon and germanium has been known since the work of Smith at Bell Laboratories in 1954. Since then, researchers have extensively reported on microscale, piezoresistive strain gauges, pressure sensors, accelerometers, and cantilever force/displacement sensors, including many commercially successful devices. In this paper, we review the history of piezoresistance, its physics and related fabrication techniques. We also discuss electrical noise in piezoresistors, device examples and design considerations, and alternative materials. This paper provides a comprehensive overview of integrated piezoresistor technology with an introduction to the physics of piezoresistivity, process and material selection and design guidance useful to researchers and device engineers.

/pdf/review-semiconductor-piezoresistance-for-microsystems-2i2jehwa4g.pdf

Review: Semiconductor Piezoresistance for Microsystems

Results presented in this letter demonstrate that the effective channel mobility of lateral, inversion-mode 4H-SiC MOSFETs is increased significantly after passivation of SiC/SiO/sub 2/ interface states near the conduction band edge by high temperature anneals in nitric oxide. Hi-lo capacitance-voltage (C-V) and ac conductance measurements indicate that, at 0.1 eV below the conduction band edge, the interface trap density decreases from approximately 2/spl times/10/sup 13/ to 2/spl times/10/sup 12/ eV/sup -1/ cm/sup -2/ following anneals in nitric oxide at 1175/spl deg/C for 2 h. The effective channel mobility for MOSFETs fabricated with either wet or dry oxides increases by an order of magnitude to approximately 30-35 cm/sup 2//V-s following the passivation anneals.

Improved inversion channel mobility for 4H-SiC MOSFETs following high temperature anneals in nitric oxide

Few-layered MoS2 as Schottky metal–semiconductor–metal photodetectors (MSM PDs) for use in harsh environments makes its debut as two-dimensional (2D) optoelectronics with high broadband gain (up to 13.3), high detectivity (up to ∼1010 cm Hz1/2/W), fast photoresponse (rise time of ∼70 μs and fall time of ∼110 μs), and high thermal stability (at a working temperature of up to 200 °C). Ultrahigh responsivity (0.57 A/W) of few-layer MoS2 at 532 nm is due to the high optical absorption (∼10% despite being less than 2 nm in thickness) and a high photogain, which sets up a new record that was not achievable in 2D nanomaterials previously. This study opens avenues to develop 2D nanomaterial-based optoelectronics for harsh environments in imaging techniques and light-wave communications as well as in future memory storage and optoelectronic circuits.

https://nanoenergy.kaust.edu.sa/Documents/1312.pdf

Few-Layer MoS2 with High Broadband Photogain and Fast Optical Switching for Use in Harsh Environments

Silicon carbide (SiC), a material long known with potential for high-temperature, high-power, high-frequency, and radiation hardened applications, has emerged as the most mature of the wide-bandgap (2.0 eV ≲ Eg ≲ 7.0 eV) semiconductors since the release of commercial 6HSiC bulk substrates in 1991 and 4HSiC substrates in 1994. Following a brief introduction to SiC material properties, the status of SiC in terms of bulk crystal growth, unit device fabrication processes, device performance, circuits and sensors is discussed. Emphasis is placed upon demonstrated high-temperature applications, such as power transistors and rectifiers, turbine engine combustion monitoring, temperature sensors, analog and digital circuitry, flame detectors, and accelerometers. While individual device performances have been impressive (e.g. 4HSiC MESFETs with fmax of 42 GHz and over 2.8 W mm−1 power density; 4HSiC static induction transistors with 225 W power output at 600 MHz, 47% power added efficiency (PAE), and 200 V forward blocking voltage), material defects in SiC, in particular micropipe defects, remain the primary impediment to wide-spread application in commercial markets. Micropipe defect densities have been reduced from near the 1000 cm−2 order of magnitude in 1992 to 3.5 cm−2 at the research level in 1995.

R.W. Johnson

Papers

Status of silicon carbide (SiC) as a wide-bandgap semiconductor for high-temperature applications: A review