Author
R. Wise
Bio: R. Wise is an academic researcher. The author has an hindex of 2, co-authored 2 publications receiving 125 citations.
Papers
More filters
TL;DR: In this paper, the authors present some evidence which suggests that with the correct hardware and operating procedure/methodology, consistent and high quality carbon-epoxy laminates can be produced, with the possibility of scaling up the process, as demonstrated by the micro and macro-scale mechanical test results.
Abstract: Microwave heating has several major advantages over conventional conductive heating when used to cure carbon–epoxy composites, especially in speed of processing. Despite this and many other well-known advantages, microwave heating of carbon–epoxy composites has not taken off in industry, or even academia, due to the problems associated with microwave energy distribution, arcing, tool design and (ultimately) part quality and consistency, thus leading to a large scepticism regarding the technique/technology for heating such type of materials. This paper presents some evidence which suggests that with the correct hardware and operating procedure/methodology, consistent and high quality carbon–epoxy laminates can be produced, with the possibility of scaling up the process, as demonstrated by the micro- and macro-scale mechanical test results. Additionally, the author proposes a methodology to practically measure the maximum microwave penetration depth of a carbon–epoxy composite material.
83 citations
Journal Article•
TL;DR: In this article, the authors present some evidence which suggests that with the correct hardware and operating procedure/methodology, consistent and high quality carbon-epoxy laminates can be produced, with the possibility of scaling up the process, as demonstrated by the micro and macro-scale mechanical test results.
61 citations
Cited by
More filters
TL;DR: In this paper, the fundamental principles behind efficient accelerated curing of composites using microwave radiation heating are reviewed and presented, especially focusing on the relation between penetration depth, microwave frequency, dielectric properties and cure degree.
Abstract: Accelerated curing of high performance fibre-reinforced polymer (FRP) composites via microwave heating or radiation, which can significantly reduce cure time and increase energy efficiency, has several major challenges (eg uneven depth of radiation penetration, reinforcing fibre shielding, uneven curing, introduction of hot spots etc) This article reviews the current scientific challenges with microwave curing of FRP composites considering the underlying physics of microwave radiation absorption in thermoset-matrix composites The fundamental principles behind efficient accelerated curing of composites using microwave radiation heating are reviewed and presented, especially focusing on the relation between penetration depth, microwave frequency, dielectric properties and cure degree Based on this review, major factors influencing microwave curing of thermoset-matrix composites are identified, and recommendations for efficient cure cycle design are provided
87 citations
TL;DR: In this paper, an improved fiber-bundle pull-out test was developed to solve the problem of severe arcing caused by exposed carbon fibers, which brought an increase of about 52.8% in interfacial shear strength.
65 citations
TL;DR: In this paper, a new cyclic heating and cooling methodology for microwave curing process control of composite is proposed by analyzing mechanisms of heat conduction, stress generation and curing kinetics.
Abstract: For the fabrication of carbon fibre reinforced composites used in aerospace industry, microwave curing technologies are more effective than traditional thermal curing technologies. However, the manufacturer's recommended cure cycles used in traditional autoclave curing are directly adopted into current microwave curing technologies without thorough validation. Here, a new cyclic heating and cooling methodology for microwave curing process control of composite is proposed by analyzing mechanisms of heat conduction, stress generation and curing kinetics. The results of the experiment carried out show significant reductions in residual strain, warpage, total curing time and energy consumption, compared with both traditional thermal curing and current microwave curing technologies. The mechanical properties of samples cured by the new process are compared with the autoclave cured ones.
61 citations
TL;DR: In this paper, microwave radiation was used to cure carbon fiber/bismaleimide composites aiming at shortening the production cycle time, and the optimum processing parameters for microwave curing were established based on analysis of the mechanical performance.
42 citations
TL;DR: The present study provides a simple, rapid and inexpensive approach for fabricating TENGs based on porous elastomeric nanocomposites based on PDMS via microwave irradiation, which greatly enhanced the electrical performance of T ENGs as compared to a pure solid elastomers.
Abstract: Even though porous elastomers and elastomeric nanocomposites have shown many advantages for triboelectric nanogenerators (TENGs), their fabrication techniques are relatively complicated, inefficient, and time-consuming. In this work, we introduced a simple, efficient and rapid concept to fabricate porous polydimethylsiloxane (PDMS) nanocomposites. PDMS nanocomposites with various porous structure were produced within a few minutes through just one-step microwave irradiation without any post-processing. Three solvents with different boiling points were selected as sacrificial materials to control porous structure. To fabricate nanocomposites, BaTiO3 (BT) nanoparticles were mixed into the uncured PDMS and sacrificial solvent mixture. Additionally, Ni nanoparticles were also used to understand the effect of embedded material’s property on porous structure. The porous BT/PDMS nanocomposites fabricated via microwave irradiation greatly enhanced the electrical performance of TENGs as compared to a pure solid elastomer. The present study provides a simple, rapid and inexpensive approach for fabricating TENGs based on porous elastomeric nanocomposites.
40 citations