Ramanathan Arunachalam

Bio: Ramanathan Arunachalam is an academic researcher from Sultan Qaboos University. The author has contributed to research in topics: Machining & Taguchi methods. The author has an hindex of 19, co-authored 64 publications receiving 1384 citations. Previous affiliations of Ramanathan Arunachalam include Sona College of Technology & National University of Singapore.

Machinability of nickel-based high temperature alloys

Abstract: Nickel-based high temperature alloys have excellent physical properties, which make them ideal for use in the manufacture of aerospace components. However, they exhibit poor machinability. Though conventional machining in industries is currently being carried out using carbide tools, there is little scope for improving the material removal rate. Machining, being a major operation, needs to be improved in order to reduce the throughput time. High Speed Machining (HSM) is a promising technique for increasing productivity in this regard. This paper mostly reviews research and development work in the machining of nickel-based high temperature alloys carried out over the last 15 years with the objective of assessing the present scenario. Emphasis is laid on Inconel 718, which is most commonly used. Both turning and milling operations using conventional and High Speed (HS) machining are reviewed herein. HSM is discussed at length in comparison with conventional machining, as it is possible to drastical...

Residual stress and surface roughness when facing age hardened Inconel 718 with CBN and ceramic cutting tools

Abstract: The demand for increasing productivity when machining heat resistant super alloys has resulted in the use of advanced cutting tools such as ceramics and cubic boron nitride (CBN). However, the effects of these tools on the surface integrity, especially the residual stresses created, in the high speed facing operation of Inconel 718 has not been dealt with. In this paper, the residual stresses and the surface roughness when facing age hardened Inconel 718 using CBN and mixed ceramic cutting tools at their respective optimum performance based on productivity has been investigated. The residual stress and surface finish generated during facing with CBN cutting tools have been investigated as a function of speed, depth of cut, coolant, tool geometry and nature of the tool coating. In addition, mixed ceramic cutting tools have been investigated for comparison. The results show that mixed ceramic cutting tools induce tensile residual stresses with a much higher magnitude than CBN cutting tools. The residual stresses and the surface roughness generated by CBN cutting tools are more sensitive to cutting speeds than depth of cut. The use of coolant results in either compressive residual stresses or lowers the magnitude of the tensile residual stresses, whereas dry cutting always resulted in tensile residual stresses. From this investigation, it is suggested that round CBN cutting tools should be used at slow cutting speeds (150 m/min) and small depths of cut (0.05 mm) and with the use of coolant to achieve compressive or minimal tensile residual stresses and good surface finish.

Surface integrity when machining age hardened Inconel 718 with coated carbide cutting tools

Abstract: Considerable attention has been given to the use of ceramic cutting tools for improving productivity in the machining of heat resistant super alloys (HRSA). However, because of their negative influence on the surface integrity, ceramic tools are generally avoided particularly for finishing applications. As a result the main high end manufacturers are more or less dependent on carbide cutting tools for finishing operations. Still the improper use of carbide cutting tools can also result in poor surface integrity. The objective of this investigation is to develop a set of guidelines, which will assist the selection of the appropriate cutting tools and conditions for generating favorable compressive residual stresses. This paper specifically deals with residual stresses and surface finish components of surface integrity when machining (facing) age hardened Inconel 718 using two grades of coated carbide cutting tools specifically developed for machining HRSAs. The cutting conditions were obtained from investigations based on optimum tool performance. The effect of insert shape, cutting edge preparation, type and nose radius on both residual stresses and surface finish was studied at this optimum cutting condition. This investigation, suggested that coated carbide cutting tool inserts of round shape, chamfered cutting edge preparation, negative type and small nose radius (0.8 mm) and coolant will generate primarily compressive residual stresses.

Machinability of natural fiber reinforced composites: a review

Abstract: In the recent years with greater emphasis on the environmental and sustainability aspects of engineering materials, natural fiber reinforced composites (NFRCs) are gaining more importance because of their numerous advantages. Several researchers have developed NFRCs using various natural fibers as well as matrix materials. However, real-world applications of NFRCs require some secondary operations in order to complete the assembly of the components or parts. Very few researchers have discussed issues related to the machinability of these NFRCs. In this paper, for the first time, a comprehensive literature review on machining of NFRCs is discussed with focus on drilling operation. The paper also reviews the studies on milling and turning of NFRCs. The distinct feature of this review is that it identifies the factors that affect the quality of the machined feature and provides general recommendations for the selection of process parameters so as to generate better quality holes during drilling. In addition, the review also discusses the challenges that hinder machining of NFRCs which is a significant contribution to the field of NFRCs.

Machining induced surface integrity in titanium and nickel alloys: A review

Abstract: Titanium and nickel alloys represent a significant metal portion of the aircraft structural and engine components. When these critical structural components in aerospace industry are manufactured with the objective to reach high reliability levels, surface integrity is one of the most relevant parameters used for evaluating the quality of finish machined surfaces. The residual stresses and surface alteration (white etch layer and depth of work hardening) induced by machining of titanium alloys and nickel-based alloys are very critical due to safety and sustainability concerns. This review paper provides an overview of machining induced surface integrity in titanium and nickel alloys. There are many different types of surface integrity problems reported in literature, and among these, residual stresses, white layer and work hardening layers, as well as microstructural alterations can be studied in order to improve surface qualities of end products. Many parameters affect the surface quality of workpieces, and cutting speed, feed rate, depth of cut, tool geometry and preparation, tool wear, and workpiece properties are among the most important ones worth to investigate. Experimental and empirical studies as well as analytical and Finite Element modeling based approaches are offered in order to better understand machining induced surface integrity. In the current state-of-the-art however, a comprehensive and systematic modeling approach based on the process physics and applicable to the industrial processes is still missing. It is concluded that further modeling studies are needed to create predictive physics-based models that is in good agreement with reliable experiments, while explaining the effects of many parameters, for machining of titanium alloys and nickel-based alloys.

A review of developments towards dry and high speed machining of Inconel 718 alloy

Abstract: The increasing attention to the environmental and health impacts of industry activities by governmental regulation and by the growing awareness in society is forcing manufacturers to reduce the use of lubricants. In the machining of aeronautical materials, classified as difficult-to-machine materials, the consumption of cooling lubricant during the machining operations is very important. The associated costs of coolant acquisition, use, disposal and washing the machined components are significant, up to four times the cost of consumable tooling used in the cutting operations. To reduce the costs of production and to make the processes environmentally safe, the goal of the aeronautical manufacturers is to move toward dry cutting by eliminating or minimising cutting fluids. This goal can be achieved by a clear understanding of the cutting fluid function in machining operations, in particular in high speed cutting, and by the development and the use of new materials for tools and coatings. High speed cutting is another important aspect of advanced manufacturing technology introduced to achieve high productivity and to save machining cost. The combination of high speed cutting and dry cutting for difficult-to-cut aerospace materials is the growing challenge to deal with the economic, environmental and health aspects of machining. In this paper, attention is focussed on Inconel 718 and recent work and advances concerning machining of this material are presented. In addition, some solutions to reduce the use of coolants are explored, and different coating techniques to enable a move towards dry machining are examined.

Tool wear characteristics in machining of nickel-based superalloys

Abstract: Nickel-based superalloy is widely employed in aircraft engines and the hot end components of various types of gas turbines with its high strength, strong corrosion resistance and excellent thermal fatigue properties and thermal stability. However, nickel-based superalloy is one of the extremely difficult-to-cut materials. During the machining process, the interaction between the tool and the workpiece causes the severe plastic deformation in the local area of workpiece, and the intense friction at the tool–workpiece interface. The resulting cutting heat coupled with the serious work hardening leads to a series of flaws, such as excessive tool wear, frequent tool change, short tool life, low productivity, and large amount of power consumption etc., in which the excessive tool wear has become one of the main bottlenecks that constraints the machinability of nickel-based superalloys and its wide range of applications. In this article, attention is mainly focused on the tool wear characteristics in the machining of nickel-based superalloys, and the state of the art in the fields of failure mechanism, monitoring and prediction, and control of tool wear are reviewed. The survey of existing works has revealed several gaps in the aspects of tool self-organizing process based on the non-equilibrium thermodynamics, tool wear considering the tool nose radius, thermal diffusion layer in coated tools, tool life prediction based on the thermal–mechanical coupling, and industrial application of tool wear online monitoring devices. The review aims at providing an insight into the tool wear characteristics in the machining of nickel-based superalloys and shows the great potential for further investigations and innovation in the field of tool wear.