Ramsay Chang

Bio: Ramsay Chang is an academic researcher from Electric Power Research Institute. The author has contributed to research in topics: Flue gas & Sorbent. The author has an hindex of 25, co-authored 59 publications receiving 2891 citations. Previous affiliations of Ramsay Chang include University of Illinois at Urbana–Champaign.

MnOx-CeO2 mixed oxides prepared by co-precipitation for selective catalytic reduction of NO with NH3 at low temperatures

Abstract: A series of manganese-cerium oxide catalysts were prepared by co-precipitation method and used for low temperature selective catalytic reduction (SCR) of NO x with ammonia in the presence of excess O 2 . These catalysts were characterized by X-ray diffraction (XRD), surface area measurement and FTIR. The experimental results showed that the best Mn-Ce mixed-oxide catalyst yielded 95% NO conversion at 150 °C at a space velocity of 42,000 h −1 . As the manganese content was increased from 0 to 40% (i.e. the molar ratio of Mn/(Mn+Ce)), NO conversion increased significantly, but decreased at higher manganese contents. The most active catalyst was obtained with a molar Mn/(Mn+Ce) ratio of 0.4. Only N 2 rather than N 2 O was found in the product when the temperature was below 150 °C. At higher temperatures, trace amounts of N 2 O were detected. A mechanistic pathway for this reaction was proposed based on earlier findings and FTIR results obtained in this work. The initial step was the adsorption of NH 3 on Lewis acid sites of catalyst, followed by reaction with nitrite species to produce N 2 and H 2 O. Possible intermediates are proposed and all the intermediates could transform into NH 2 NO, which could further react to produce N 2 and H 2 O.

Effects of sulfur impregnation temperature on the properties and mercury adsorption capacities of activated carbon fibers (ACFs)

Abstract: Laboratory studies were conducted to determine the role of sulfur functional groups and micropore surface area of carbon-based adsorbents on the adsorption of Hg0 from simulated coal combustion flue gases. In this study, raw activated carbon fibers that are microporous (ACF-20) were impregnated with elemental sulfur between 250 and 650 degrees C. The resulting samples were saturated with respect to sulfur content. Total sulfur content of the sulfur impregnated ACF samples decreased with increasing impregnation temperatures from 250 and 500 degrees C and then remained constant to 650 degrees C. Results from sulfur K-edge X-ray absorption near-edge structure (S-XANES) spectroscopy showed that sulfur impregnated on the ACF samples was in both elemental and organic forms. As sulfur impregnation temperature increased, however, the relative amounts of elemental sulfur decreased with a concomitant increase in the amount of organic sulfur. Thermal analyses and mass spectrometry revealed that sulfur functional groups formed at higher impregnation temperatures were more thermally stable. In general, sulfur impregnation decreased surface area and increased equilibrium Hg0 adsorption capacity when compared to the raw ACF sample. The ACF sample treated with sulfur at 400 degrees C had a surface area of only 94 m2/g compared to the raw ACF sample's surface area of 1971 m2/g, but at least 86% of this sample's surface area existed as micropores and it had the largest equilibrium Hg0 adsorption capacities (2211-11,343 micrograms/g). Such a result indicates that 400 degrees C is potentially an optimal sulfur impregnation temperature for this ACF. Sulfur impregnated on the ACF that was treated at 400 degrees C was in both elemental and organic forms. Thermal analyses and CS2 extraction tests suggested that elemental sulfur was the main form of sulfur affecting the Hg0 adsorption capacity. These findings indicate that both the presence of elemental sulfur on the adsorbent and a microporous structure are important properties for improving the performance of carbon-based adsorbents for the removal of Hg0 from coal combustion flue gases.

Factors Affecting Mercury Control in Utility Flue Gas Using Activated Carbon.

Abstract: The Electric Power Research Institute (EPRI) is conducting research to investigate mercury removal in utility flue gas using sorbents. Bench-scale and pilot-scale tests have been conducted to determine the abilities of different sor-bents to remove mercury in simulated and actual flue gas streams. Bench-scale tests have investigated the effects of various sorbent and flue gas parameters on sorbent performance. These data are being used to develop a theoretical model for predicting mercury removal by sorbents at different conditions. This paper describes the results of parametric bench-scale tests investigating the removal of mercuric chloride and elemental mercury by activated carbon. Results obtained to date indicate that the adsorption capacity of a given sorbent is dependent on many factors, including the type of mercury being adsorbed, flue gas composition, and adsorption temperature. These data provide insight into potential mercury adsorption mechanisms and suggest that the removal of mercu...

Mercury Adsorption Properties of Sulfur-Impregnated Adsorbents

Abstract: Carbonaceous and noncarbonaceous adsorbents were impregnated with elemental sulfur to evaluate the chemical and physical properties of the adsorbents and their equilibrium mercury adsorption capacities. Simulated coal combustion flue gas conditions were used to determine the equilibrium adsorption capacities for Hg 0 and HgCl2 gases to better understand how to remove mercury from gas streams generated by coal-fired utility power plants. Sulfur was deposited onto the adsorbents by monolayer surface deposition or volume pore filling. Sulfur impregnation increased the total sulfur content and decreased the total and micropore surface areas and pore volumes for all of the adsorbents tested. Adsorbents with sufficient amounts of active adsorption sites and sufficient microporous structure had mercury adsorption capacities up to 4,509 mg Hg/g adsorbent. Elemental sulfur, organic sulfur, and sulfate were formed on the adsorbents during sulfur impregnation. Correlations were established with R 2 .0.92 between the equilibrium Hg 0 /HgCl2 adsorption capacities and the mass concentrations of elemental and organic sulfur. This result indicates that elemental and organic sulfur are important active adsorption sites for Hg 0 and HgCl2 .

MnOx-CeO2 mixed oxides prepared by co-precipitation for selective catalytic reduction of NO with NH3 at low temperatures

Abstract: A series of manganese-cerium oxide catalysts were prepared by co-precipitation method and used for low temperature selective catalytic reduction (SCR) of NO x with ammonia in the presence of excess O 2 . These catalysts were characterized by X-ray diffraction (XRD), surface area measurement and FTIR. The experimental results showed that the best Mn-Ce mixed-oxide catalyst yielded 95% NO conversion at 150 °C at a space velocity of 42,000 h −1 . As the manganese content was increased from 0 to 40% (i.e. the molar ratio of Mn/(Mn+Ce)), NO conversion increased significantly, but decreased at higher manganese contents. The most active catalyst was obtained with a molar Mn/(Mn+Ce) ratio of 0.4. Only N 2 rather than N 2 O was found in the product when the temperature was below 150 °C. At higher temperatures, trace amounts of N 2 O were detected. A mechanistic pathway for this reaction was proposed based on earlier findings and FTIR results obtained in this work. The initial step was the adsorption of NH 3 on Lewis acid sites of catalyst, followed by reaction with nitrite species to produce N 2 and H 2 O. Possible intermediates are proposed and all the intermediates could transform into NH 2 NO, which could further react to produce N 2 and H 2 O.

Solution Combustion Synthesis of Nanoscale Materials

Abstract: Solution combustion is an exciting phenomenon, which involves propagation of self-sustained exothermic reactions along an aqueous or sol–gel media. This process allows for the synthesis of a variety of nanoscale materials, including oxides, metals, alloys, and sulfides. This Review focuses on the analysis of new approaches and results in the field of solution combustion synthesis (SCS) obtained during recent years. Thermodynamics and kinetics of reactive solutions used in different chemical routes are considered, and the role of process parameters is discussed, emphasizing the chemical mechanisms that are responsible for rapid self-sustained combustion reactions. The basic principles for controlling the composition, structure, and nanostructure of SCS products, and routes to regulate the size and morphology of the nanoscale materials are also reviewed. Recently developed systems that lead to the formation of novel materials and unique structures (e.g., thin films and two-dimensional crystals) with unusual...