Raquel González-Arrabal

Bio: Raquel González-Arrabal is an academic researcher from Technical University of Madrid. The author has contributed to research in topics: Thin film & Sputtering. The author has an hindex of 20, co-authored 67 publications receiving 934 citations. Previous affiliations of Raquel González-Arrabal include Autonomous University of Madrid & Vienna University of Technology.

Tribomechanical properties of hard Cr-doped DLC coatings deposited by low-frequency HiPIMS

Abstract: Cr-doped diamond-like carbon (Cr-DLC) films with Cr contents ranging from 3 up to 20 at. % were synthesised in a codeposition process with HiPIMS (Cr deposition) and DC-pulsed technology (C deposition). The application of HiPIMS at low frequencies was observed to significantly enhance the energy density during the Cr plasma discharge due to the interaction of Cr–C species. The higher energy bombardment at low HiPIMS frequencies allowed doping with Cr the DLC structure avoiding the graphitization of the carbon structure. EELS spectroscopy was used to evaluate sp3 content and Raman was used for sp2 structural characterization of the films. Enhanced mechanical properties (hardness up to 30 GPa) were observed with nanoindentation for Cr-doped DLC at low frequencies. High temperature nanoindentation tests were also performed from room temperature to 425 °C in order to evaluate the evolution of hardness and Young Modulus with temperature. The results showed that the mechanical properties at high temperature mainly depend on the initial sp3-sp2 structure. Tribological tests were carried out in air from room temperature to 250 °C. Cr-doped DLC coatings deposited by low-frequency HiPIMS showed lower friction and wear compared to undoped DLC.

The influence of positive pulses on HiPIMS deposition of hard DLC coatings

Abstract: Diamond-like Carbon (DLC) coatings were deposited by a novel HiPIMS method that incorporates positive voltage pulses at the end of the conventional HiPIMS discharge. Different positive voltage amplitudes (100, 200, 300, 400 and 500 V) were used to evaluate the effect of this operation mode on the discharge process and the mechanical properties of the deposited DLC coatings. The application of positive pulses was observed to enhance the ionization of both the sputtered carbon and argon species. Mass spectroscopy measurements showed that a larger amount of high-energy C+ ions are generated, with ion energies proportional to the amplitude of the overshoot voltage. The ion bombardment induced by the positive pulses led to higher compressive residual stresses and densification of deposited DLC coatings. Moreover, their Raman spectra exhibited lower D-band and G-band intensity ratios (ID/IG) as the pulses voltage was increased which is indicative of higher sp3 content. Mechanical properties were evaluated by nanoindentation testing and the hardness of the deposited DLC films was observed to increase from 9.6 GPa (for no voltage pulse applied) to 22.5 GPa (for an applied positive pulse voltage of 500 V).

Limitations for the trapped field in large grain YBCO superconductors

Abstract: The actual limitations for the trapped field in YBa2Cu3O7?? (YBCO) monoliths are discussed. The influence of the sample geometry and of the critical current density on the trapped field is investigated by numerical calculations. The field dependence of the critical current density strongly influences the trapped field. A nonlinear relationship between the sample size, the critical current density and the resulting trapped field is derived. The maximum achievable trapped field in YBCO at 77?K is found to be around 2.5?T. This limit is obtained for reasonable geometries and high but realistic critical current densities. Such high fields have not been reached experimentally so far, due to non-optimized flux pinning and material inhomogeneities. These inhomogeneities can be directly assessed by the magnetoscan technique, and their influence is discussed. Significant differences between the a-?and the c-growth sectors were found. Limitations due to cracks and non-superconducting inclusions (e.g.?211 particles) are estimated and found to be candidates for variations of Jc on a millimetre length scale, as observed in experiments.

Fast parallel algorithms for short-range molecular dynamics

Abstract: Three parallel algorithms for classical molecular dynamics are presented. The first assigns each processor a fixed subset of atoms; the second assigns each a fixed subset of inter-atomic forces to compute; the third assigns each a fixed spatial region. The algorithms are suitable for molecular dynamics models which can be difficult to parallelize efficiently—those with short-range forces where the neighbors of each atom change rapidly. They can be implemented on any distributed-memory parallel machine which allows for message-passing of data between independently executing processors. The algorithms are tested on a standard Lennard-Jones benchmark problem for system sizes ranging from 500 to 100,000,000 atoms on several parallel supercomputers--the nCUBE 2, Intel iPSC/860 and Paragon, and Cray T3D. Comparing the results to the fastest reported vectorized Cray Y-MP and C90 algorithm shows that the current generation of parallel machines is competitive with conventional vector supercomputers even for small problems. For large problems, the spatial algorithm achieves parallel efficiencies of 90% and a 1840-node Intel Paragon performs up to 165 faster than a single Cray C9O processor. Trade-offs between the three algorithms and guidelines for adapting them to more complex molecular dynamics simulations are also discussed.

Nuclear Tracks in Solids (Principles and Applications)

Abstract: (1976). Nuclear Tracks in Solids (Principles and Applications) Nuclear Technology: Vol. 30, No. 1, pp. 91-92.

Superconductor bearings, flywheels and transportation

Abstract: This paper describes the present status of high temperature superconductors (HTS) and of bulk superconducting magnet devices, their use in bearings, in flywheel energy storage systems (FESS) and linear transport magnetic levitation (Maglev) systems. We report and review the concepts of multi-seeded REBCO bulk superconductor fabrication. The multi-grain bulks increase the averaged trapped magnetic flux density up to 40% compared to single-grain assembly in large-scale applications. HTS magnetic bearings with permanent magnet (PM) excitation were studied and scaled up to maximum forces of 10 kN axially and 4.5 kN radially. We examine the technology of the high-gradient magnetic bearing concept and verify it experimentally. A large HTS bearing is tested for stabilizing a 600 kg rotor of a 5 kWh/250 kW flywheel system. The flywheel rotor tests show the requirement for additional damping. Our compact flywheel system is compared with similar HTS–FESS projects. A small-scale compact YBCO bearing with in situ Stirling cryocooler is constructed and investigated for mobile applications. Next we show a successfully developed modular linear Maglev system for magnetic train operation. Each module levitates 0.25t at 10 mm distance during one-day operation without refilling LN2. More than 30 vacuum cryostats containing multi-seeded YBCO blocks are fabricated and are tested now in Germany, China and Brazil.