Ricardo Pereira

Bio: Ricardo Pereira is an academic researcher from State University of Campinas. The author has contributed to research in topics: Cyclohexane & Catalysis. The author has an hindex of 7, co-authored 8 publications receiving 759 citations.

Cyclohexane oxidation continues to be a challenge

Abstract: Many efforts have been made to develop new catalysts to oxidize cyclohexane under mild conditions. Herein, we review the most interesting systems for this process with different oxidants such as hydrogen peroxide, tert -butyl hydroperoxide and molecular oxygen. Using H 2 O 2 , Na-GeX has been shown to be a most stable and active catalyst. Mesoporous TS-1 and Ti-MCM-41 are also stable, but the use of other metals such as Cr, V, Fe and Mo leads to leaching of the metal. Homogeneous systems based on binuclear manganese(IV) complexes have also been shown to be interesting. When t -BuOOH is used, the active systems are those phthalocyanines based on Ru, Co and Cu and polyoxometalates of dinuclear ruthenium and palladium. Microporous metallosilicates containing different transition metals showed leaching of the metal during the reactions. Molecular oxygen can be used directly as an oxidant and decreases the leaching of active species in comparison to hydrogen peroxide and tert -butyl hydroperoxide. Metal aluminophosphates (metal: Mn, Fe, Co, Cu, Cr V) are active and relatively stable under such conditions. Mn-AlPO-36 yields directly adipic acid, but large amounts of carboxylic acids should be avoided, as they cause metal leaching from the catalysts. Rare earth exchanged zeolite Y also shows good selectivity and activity. In the last part of the review, novel alternative strategies for the production of cyclohexanol and cyclohexanone and the direct synthesis of adipic acid are discussed.

Iron(III) and copper(II) catalysed cyclohexane oxidation by molecular oxygen in the presence of tert-butyl hydroperoxide

Abstract: In the presence of cyclohexane soluble iron and copper catalysts, tert-butyl hydroperoxide selectively oxidises cyclohexane to cyclohexanol and cyclohexanone (with cyclohexene for the copper catalysts). Under reflux for 24 h, the conversions are 4 to 5% (turnover numbers of 70 to 90) and the selectivities above 90%. Under 25 bar of oxygen at 70°C for 24 h, conversions with the iron catalysts are 9% (turnover numbers of up to 166) but the selectivities are below 80%, as large amounts of adipic acid are also formed. The copper catalysts are more selective under these conditions. Using Cu(tma)2 the conversion is 11% (turnover number of 192) and the selectivity is 91%. Reactions in the presence of cyclohexanone show that the iron catalysts deactivate by complexation with the adipic acid formed by its over-oxidation. The copper catalysts rapidly produce cyclohexene at the beginning of the reactions; this is further oxidised to cyclohexen-3-one and cyclohexen-3-ol, thus reducing the catalyst activity for cyclohexane oxidation.

Baker's yeast : some biochemical aspects and their influence in biotransformations

Abstract: Baker’s yeast is becoming an important reagent for organic synthesis. However, on many occasions, there are problems with the experimental reproducibility, which in general is the result of the different origins of baker’s yeasts. In order to explain these differences, NAD (P)+ reduction inside intact living cells from different strains was measured. The method can select cells with better reduction power in a short period of time.

Polymeric Graphitic Carbon Nitride as a Heterogeneous Organocatalyst: From Photochemistry to Multipurpose Catalysis to Sustainable Chemistry

Abstract: Polymeric graphitic carbon nitride materials (for simplicity: g-C(3)N(4)) have attracted much attention in recent years because of their similarity to graphene. They are composed of C, N, and some minor H content only. In contrast to graphenes, g-C(3)N(4) is a medium-bandgap semiconductor and in that role an effective photocatalyst and chemical catalyst for a broad variety of reactions. In this Review, we describe the "polymer chemistry" of this structure, how band positions and bandgap can be varied by doping and copolymerization, and how the organic solid can be textured to make it an effective heterogenous catalyst. g-C(3)N(4) and its modifications have a high thermal and chemical stability and can catalyze a number of "dream reactions", such as photochemical splitting of water, mild and selective oxidation reactions, and--as a coactive catalytic support--superactive hydrogenation reactions. As carbon nitride is metal-free as such, it also tolerates functional groups and is therefore suited for multipurpose applications in biomass conversion and sustainable chemistry.

Aerobic Copper-Catalyzed Organic Reactions

Abstract: The chemistry of copper is extremely rich because it can easily access Cu0, CuI, CuII, and CuIII oxidation states allowing it to act through one-electron or two-electron processes. As a result, both radical pathways and powerful two-electron bond forming pathways via organmetallic intermediates, similar to those of palladium, can occur. In addition, the different oxidation states of copper associate well with a large number of different functional groups via Lewis acid interactions or π-coordination. In total, these feature confer a remarkably broad range of activities allowing copper to catalyze the oxidation and oxidative union of many substrates. Oxygen is a highly atom economical, environmentally benign, and abundant oxidant, which makes it ideal in many ways.1 The high activation energies in the reactions of oxygen require that catalysts be employed.2 In combination with molecular oxygen, the chemistry of copper catalysis increases exponentially since oxygen can act as either a sink for electrons (oxidase activity) and/or as a source of oxygen atoms that are incorporated into the product (oxygenase activity). The oxidation of copper with oxygen is a facile process allowing catalytic turnover in net oxidative processes and ready access to the higher CuIII oxidation state, which enables a range of powerful transformations including two-electron reductive elimination to CuI. Molecular oxygen is also not hampered by toxic byproducts, being either reduced to water, occasionally via H2O2 (oxidase activity) or incorporated into the target structure with high atom economy (oxygenase activity). Such oxidations using oxygen or air (21% oxygen) have been employed safely in numerous commodity chemical continuous and batch processes.3 However, batch reactors employing volatile hydrocarbon solvents require that oxygen concentrations be kept low in the head space (typically <5–11%) to avoid flammable mixtures, which can limit the oxygen concentration in the reaction mixture.4,5,6 A number of alternate approaches have been developed allowing oxidation chemistry to be used safely across a broader array of conditions. For example, use of carbon dioxide instead of nitrogen as a diluent leads to reduced flammability.5 Alternately, water can be added to moderate the flammability allowing even pure oxygen to be employed.6 New reactor designs also allow pure oxygen to be used instead of diluted oxygen by maintaining gas bubbles in the solvent, which greatly improves reaction rates and prevents the build up of higher concentrations of oxygen in the head space.4a,7 Supercritical carbon dioxide has been found to be advantageous as a solvent due its chemical inertness towards oxidizing agents and its complete miscibility with oxygen or air over a wide range of temperatures.8 An number of flow technologies9 including flow reactors,10 capillary flow reactors,11 microchannel/microstructure structure reactors,12 and membrane reactors13 limit the amount of or afford separation of hydrocarbon/oxygen vapor phase thereby reducing the potential for explosions. Enzymatic oxidizing systems based upon copper that exploit the many advantages and unique aspects of copper as a catalyst and oxygen as an oxidant as described in the preceding paragraphs are well known. They represent a powerful set of catalysts able to direct beautiful redox chemistry in a highly site-selective and stereoselective manner on simple as well as highly functionalized molecules. This ability has inspired organic chemists to discover small molecule catalysts that can emulate such processes. In addition, copper has been recognized as a powerful catalyst in several industrial processes (e.g. phenol polymerization, Glaser-Hay alkyne coupling) stimulating the study of the fundamental reaction steps and the organometallic copper intermediates. These studies have inspiried the development of nonenzymatic copper catalysts. For these reasons, the study of copper catalysis using molecular oxygen has undergone explosive growth, from 30 citations per year in the 1980s to over 300 citations per year in the 2000s. A number of elegant reviews on the subject of catalytic copper oxidation chemistry have appeared. Most recently, reviews provide selected coverage of copper catalysts14 or a discussion of their use in the aerobic functionalization of C–H bonds.15 Other recent reviews cover copper and other metal catalysts with a range of oxidants, including oxygen, but several reaction types are not covered.16 Several other works provide a valuable overview of earlier efforts in the field.17 This review comprehensively covers copper catalyzed oxidation chemistry using oxygen as the oxidant up through 2011. Stoichiometric reactions with copper are discussed, as necessary, to put the development of the catalytic processes in context. Mixed metal systems utilizing copper, such as palladium catalyzed Wacker processes, are not included here. Decomposition reactions involving copper/oxygen and model systems of copper enzymes are not discussed exhaustively. To facilitate analysis of the reactions under discussion, the current mechanistic hypothesis is provided for each reaction. As our understanding of the basic chemical steps involving copper improve, it is expected that many of these mechanisms will evolve accordingly.

Magnetically Separable Nanocatalysts: Bridges between Homogeneous and Heterogeneous Catalysis

Abstract: Recovery and reuse of expensive catalysts after catalytic reactions are important factors for sustainable process management. The aim of this Review is to highlight the progress in the formation and catalytic applications of magnetic nanoparticles and magnetic nanocomposites. Directed functionalization of the surfaces of nanosized magnetic materials is an elegant way to bridge the gap between heterogeneous and homogeneous catalysis. The introduction of magnetic nanoparticles in a variety of solid matrices allows the combination of well-known procedures for catalyst heterogenization with techniques for magnetic separation.

Cantilever transducers as a platform for chemical and biological sensors

Abstract: Since the late 1980s there have been spectacular developments in micromechanical or microelectro-mechanical (MEMS) systems which have enabled the exploration of transduction modes that involve mechanical energy and are based primarily on mechanical phenomena. As a result an innovative family of chemical and biological sensors has emerged. In this article, we discuss sensors with transducers in a form of cantilevers. While MEMS represents a diverse family of designs, devices with simple cantilever configurations are especially attractive as transducers for chemical and biological sensors. The review deals with four important aspects of cantilever transducers: (i) operation principles and models; (ii) microfabrication; (iii) figures of merit; and (iv) applications of cantilever sensors. We also provide a brief analysis of historical predecessors of the modern cantilever sensors.

Bernoulli–Euler beam model based on a modified couple stress theory

Abstract: A new model for the bending of a Bernoulli–Euler beam is developed using a modified couple stress theory. A variational formulation based on the principle of minimum total potential energy is employed. The new model contains an internal material length scale parameter and can capture the size effect, unlike the classical Bernoulli–Euler beam model. The former reduces to the latter in the absence of the material length scale parameter. As a direct application of the new model, a cantilever beam problem is solved. It is found that the bending rigidity of the cantilever beam predicted by the newly developed model is larger than that predicted by the classical beam model. The difference between the deflections predicted by the two models is very significant when the beam thickness is small, but is diminishing with the increase of the beam thickness. A comparison shows that the predicted size effect agrees fairly well with that observed experimentally.