Robert Louis Steigerwald

Bio: Robert Louis Steigerwald is an academic researcher from General Electric. The author has contributed to research in topics: Boost converter & Inverter. The author has an hindex of 49, co-authored 201 publications receiving 9544 citations.

A comparison of half-bridge resonant converter topologies

Abstract: The half-bridge series-resonant, parallel-resonant, and combination series-parallel resonant converters are compared for use in low-output-voltage power supply applications. It is shown that the combination series-parallel converter, which takes on the desirable characteristics of the pure series and the pure parallel converter, avoids the main disadvantages of each of them. Analyses and breadboard results show that the combination converter can run over a large input voltage range and a large load range (no load to full load) while maintaining excellent efficiency. A useful analysis technique based on classical AC complex analysis is introduced. >

A comparison of half-bridge resonant converter topologies

Abstract: The half-bridge series resonant, parallel resonant and combination series-parallel resonant converters are compared for use in low output voltage power supply applications. It is shown that the combination series-parallel converter, which takes on the desirable characteristics of the pure series and the pure parallel converter, removes the main disadvantages of those two converters. Analyses and breadboard results show that the combination series-parallel converter can run over a large input voltage range and a large load range (no-load to full-load) while while maintaining excellent efficiency. A useful analysis technique based on classical ac complex analysis is also introduced.

High-Frequency Resonant Transistor DC-DC Converters

Abstract: Transistor dc-dc converters which employ a resonant circuit are described. A resonant circuit is driven with square waves of current or voltage, and by adjusting the frequency around the resonant point, the voltage on the resonant components can be adjusted to any practical voltage level. By rectifying the voltage across the resonant elements, a dc voltage is obtained which can be either higher or lower than the input dc voltage to the converter. Thus, the converter can operate in either the step-up or step-down mode. In addition, the switching losses in the inverter devices and rectifiers are extremely low due to the sine waves that occur from the use of a resonant circuit (as opposed to square waves in a conventional converter); also, easier EMI filtering should result. In the voltage input version, the converter is able to use the parasitic diode associated with an FET or monolithic Darlington, while in the current input version, the converter needs the inverse blocking capability which can be obtained with an IGT or GTO device. A low-power breadboard operating at 200-300 kHz has been built. Two typical application areas are switching power supplies and battery chargers. The converter circuits offer improvements over conventional circuits due to their high efficiency (low switching losses), small reactive components (high-frequency operation), and their step-up/stepdown ability.

Microcomputer Control of a Residential Photovoltaic Power Conditioning System

Abstract: Microcomputer-based control of a residential photovoltaic power conditioning system is described. The microcomputer is responsible for array current feedback control, maximum power tracking control, array safe zone steering control, phase-locked reference wave synthesis, sequencing control, and some diagnostics. The control functions are implemented using Intel 8751 single-chip microcomputer-based hardware and software. The controller has been tested in the laboratory with the prototype power conditioner and shows excellent performance.

An AC-to-DC Converter with High Quality Input Waveforms

Abstract: An ac-to-dc converter which draws sinusoidal and inphase current waveforms from the ac power source is described. Harmonic and power factor measurements obtained from a field- effect transistor (FET) converter operating at 45 kHz for a single- phase and a three-phase connection are presented. A stability analysis and design methodology are given.

A three-phase soft-switched high power density DC/DC converter for high power applications

Abstract: Three DC/DC converter topologies suitable for high-power-density high-power applications are presented. All three circuits operate in a soft-switched manner, making possible a reduction in device switching losses and an increase in switching frequency. The three-phase dual-bridge converter proposed is shown to have the most favorable characteristics. This converter consists of two three-phase inverter stages operating in a high-frequency six-step mode. In contrast to existing single-phase AC-link DC/DC converters, lower turn-off peak currents in the power devices and lower RMS current ratings for both the input and output filter capacitors are obtained. This is in addition to smaller filter element values due to the higher-frequency content of the input and output waveforms. Furthermore, the use of a three-phase symmetrical transformer instead of single-phase transformers and a better utilization of the available apparent power of the transformer (as a consequence of the controlled output inverter) significantly increase the power density attainable. >

A comparison of half-bridge resonant converter topologies

Abstract: The half-bridge series-resonant, parallel-resonant, and combination series-parallel resonant converters are compared for use in low-output-voltage power supply applications. It is shown that the combination series-parallel converter, which takes on the desirable characteristics of the pure series and the pure parallel converter, avoids the main disadvantages of each of them. Analyses and breadboard results show that the combination converter can run over a large input voltage range and a large load range (no load to full load) while maintaining excellent efficiency. A useful analysis technique based on classical AC complex analysis is introduced. >

Powered surgical instrument

Abstract: A surgical instrument including a handle assembly, a first endoscopic portion, a motor, and a first end effector is disclosed. The first endoscopic portion is selectively connectable to a distal portion of the handle assembly and defines a longitudinal axis. The first endoscopic portion includes a housing adjacent its proximal portion and includes an actuation member. The motor is disposed in mechanical cooperation with the housing of the first endoscopic portion and is operatively connected to the actuation member for moving the actuation member substantially along the longitudinal axis. The first end effector is selectively connectable to a distal portion of the first endoscopic portion and is configured to perform a first stapling function.

Development of a microcontroller-based, photovoltaic maximum power point tracking control system

Abstract: Maximum power point tracking (MPPT) is used in photovoltaic (PV) systems to maximize the photovoltaic array output power, irrespective of the temperature and irradiation conditions and of the load electrical characteristics. A new MPPT system has been developed, consisting of a buck-type DC/DC converter, which is controlled by a microcontroller-based unit. The main difference between the method used in the proposed MPPT system and other techniques used in the past is that the PV array output power is used to directly control the DC/DC converter, thus reducing the complexity of the system. The resulting system has high-efficiency, lower-cost and can be easily modified to handle more energy sources (e.g., wind-generators). The experimental results show that the use of the proposed MPPT control increases the PV output power by as much as 15% compared to the case where the DC/DC converter duty cycle is set such that the PV array produces the maximum power at 1 kW/m/sup 2/ and 25/spl deg/C.

Step-Up DC–DC Converters: A Comprehensive Review of Voltage-Boosting Techniques, Topologies, and Applications

Abstract: DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques.