Robert P. Wei

Bio: Robert P. Wei is an academic researcher from Lehigh University. The author has contributed to research in topics: Fracture mechanics & Corrosion fatigue. The author has an hindex of 34, co-authored 104 publications receiving 4190 citations.

Microconstituent-Induced Pitting Corrosion in Aluminum Alloy 2024-T3

Abstract: Free corrosion immersion experiments were conducted on a commercial airframe material, Al 2024-T3 (UNS A92024), in 0.5 M sodium chloride (NaCl) solution to investigate the role of microcon...

A transmission electron microscopy study of constituent-particle-induced corrosion in 7075-T6 and 2024-T3 aluminum alloys

Abstract: To better understand particle-induced pitting corrosion in aluminum alloys, thin foil specimens of 7075-T6 and 2024-T3 aluminum alloys, with identified constituent particles, were immersed in aerated 0.5M NaCl solution and then examined by transmission electron microscopy (TEM). The results clearly showed matrix dissolution around the iron- and manganese-containing particles (such as Al23CuFe4), as well as the Al2Cu particles. While Al2CuMg particles tended to dissolve relative to the matrix, limited local dissolution of the matrix was also observed around these particles. These results are consistent with scanning electron microscopy (SEM) observations of pitting corrosion and are discussed in terms of the electrochemical characteristics of the particles and the matrix.

Transition from pitting to fatigue crack growth—modeling of corrosion fatigue crack nucleation in a 2024-T3 aluminum alloy

Abstract: The nucleation of fatigue cracks from corrosion pits was investigated by conducting fatigue experiments on open-hole specimens of a 2024-T3 aluminum (bare) alloy in 0.5 M NaCl solution at room temperature and different load frequencies from 0.1 to 20 Hz. The maximum cyclic stresses applied at the hole ranged from 144 to 288 MPa and the load ratio, R , was 0.1. A specimen subjected to pre-corrosion in the NaCl solution prior to corrosion fatigue was also investigated. Pitting was found to be associated with constituent particles in the hole and pit growth often involved coalescence of individual particle-nucleated pits. Fatigue cracks typically nucleated from one or two of the larger pits, and the size of the pit at which the fatigue crack nucleates is a function of stress level and load frequency. The observations indicate that the nucleation of corrosion fatigue cracks essentially results from a competition between the processes of pitting and crack growth. Pitting predominates in the early stage of the corrosion fatigue process, and is replaced by corrosion fatigue crack growth. Based on these results, two criteria are proposed to describe the transition from pit growth to fatigue crack growth: (1) the stress intensity factor of the equivalent surface crack has to reach the threshold stress intensity factor, Δ K th , for fatigue crack growth, assuming that a corrosion pit may be modeled by an equivalent semi-elliptical surface crack, and (2) the time-based corrosion fatigue crack growth rate also exceeds the pit growth rate.

Recent developments in stainless steels

Abstract: This article presents an overview of the developments in stainless steels made since the 1990s. Some of the new applications that involve the use of stainless steel are also introduced. A brief introduction to the various classes of stainless steels, their precipitate phases and the status quo of their production around the globe is given first. The advances in a variety of subject areas that have been made recently will then be presented. These recent advances include (1) new findings on the various precipitate phases (the new J phase, new orientation relationships, new phase diagram for the Fe–Cr system, etc.); (2) new suggestions for the prevention/mitigation of the different problems and new methods for their detection/measurement and (3) new techniques for surface/bulk property enhancement (such as laser shot peening, grain boundary engineering and grain refinement). Recent developments in topics like phase prediction, stacking fault energy, superplasticity, metadynamic recrystallisation and the calculation of mechanical properties are introduced, too. In the end of this article, several new applications that involve the use of stainless steels are presented. Some of these are the use of austenitic stainless steels for signature authentication (magnetic recording), the utilisation of the cryogenic magnetic transition of the sigma phase for hot spot detection (the Sigmaplugs), the new Pt-enhanced radiopaque stainless steel (PERSS) coronary stents and stainless steel stents that may be used for magnetic drug targeting. Besides recent developments in conventional stainless steels, those in the high-nitrogen, low-Ni (or Ni-free) varieties are also introduced. These recent developments include new methods for attaining very high nitrogen contents, new guidelines for alloy design, the merits/demerits associated with high nitrogen contents, etc.

Effects of hydrogen on the properties of iron and steel

Abstract: The effects of hydrogen on the physical and mechanical properties of iron and steel are reviewed. A new mechanism for the cold work peak for hydrogen in iron is considered. Together, internal friction and mechanical properties indicate that hydrogen softens iron by enhancing screw dislocation mobility at room temperature but hardens iron by core interactions at low temperatures. No single mechanism exists for the degradation of the properties of steel by hydrogen. Instead a complex process involving many of the proposed mechanisms as contributing factors is shown to account for most degradation phenomena.