Rohit Rai

Bio: Rohit Rai is an academic researcher from Corning Inc.. The author has contributed to research in topics: Heat transfer & Welding. The author has an hindex of 12, co-authored 26 publications receiving 1446 citations. Previous affiliations of Rohit Rai include Pennsylvania State University & Indian Institute of Technology Kharagpur.

Review: friction stir welding tools

Abstract: Friction stir welding (FSW) is a widely used solid state joining process for soft materials such as aluminium alloys because it avoids many of the common problems of fusion welding. Commercial feasibility of the FSW process for harder alloys such as steels and titanium alloys awaits the development of cost effective and durable tools which lead to structurally sound welds consistently. Material selection and design profoundly affect the performance of tools, weld quality and cost. Here we review and critically examine several important aspects of FSW tools such as tool material selection, geometry and load bearing ability, mechanisms of tool degradation and process economics.

Heat transfer and fluid flow during keyhole mode laser welding of tantalum, Ti–6Al–4V, 304L stainless steel and vanadium

Abstract: Because of the complexity of several simultaneous physical processes, most heat transfer models of keyhole mode laser welding require some simplifications to make the calculations tractable. The simplifications often limit the applicability of each model to the specific materials systems for which the model is developed. In this work, a rigorous, yet computationally efficient, keyhole model is developed and tested on tantalum, Ti–6Al–4V, 304L stainless steel and vanadium. Unlike previous models, this one combines an existing model to calculate keyhole shape and size with numerical fluid flow and heat transfer calculations in the weld pool. The calculations of the keyhole profile involved a point-by-point heat balance at the keyhole walls considering multiple reflections of the laser beam in the vapour cavity. The equations of conservation of mass, momentum and energy are then solved in three dimensions assuming that the temperatures at the keyhole wall reach the boiling point of the different metals or alloys. A turbulence model based on Prandtl's mixing length hypothesis was used to estimate the effective viscosity and thermal conductivity in the liquid region. The calculated weld cross-sections agreed well with the experimental results for each metal and alloy system examined here. In each case, the weld pool geometry was affected by the thermal diffusivity, absorption coefficient, and the melting and boiling points, among the various physical properties of the alloy. The model was also used to better understand solidification phenomena and calculate the solidification parameters at the trailing edge of the weld pool. These calculations indicate that the solidification structure became less dendritic and coarser with decreasing weld velocities over the range of speeds investigated in this study. Overall, the keyhole weld model provides satisfactory simulations of the weld geometries and solidification sub-structures for diverse engineering metals and alloys.

Heat transfer and fluid flow during electron beam welding of 21Cr–6Ni–9Mn steel and Ti–6Al–4V alloy

Abstract: Electron beam welding (EBW) of two important engineering alloys, Ti–6Al–4V and 21Cr–6Ni–9Mn, was studied experimentally and theoretically The temperatures at several monitoring locations in the specimens were measured as a function of time during welding and the cross-sections of the welds were examined by optical microscopy The theoretical research involved numerical simulation of heat transfer and fluid flow during EBW The model output included temperature and velocity fields, fusion zone geometry and temperature versus time results The numerically computed fusion zone geometry and the temperature versus time plots were compared with the corresponding experimentally determined values for each weld Both the experimental and the modelling results were compared with the corresponding results for the keyhole mode laser beam welding (LBW)Both experimental and modelling results demonstrate that the fusion zone size in Ti–6Al–4V alloy was larger than that of the 21Cr–6Ni–9Mn stainless steel during both the electron beam and laser welding Higher boiling point and lower solid state thermal conductivity of Ti–6Al–4V contributed to higher peak temperatures in Ti–6Al–4V welds compared with 21Cr–6Ni–9Mn stainless steel welds In the EBW of both the alloys, there were significant velocities of liquid metal along the keyhole wall driven by the Marangoni convection In contrast, during LBW, the velocities along the keyhole wall were negligible Convective heat transfer was important in the transport of heat in the weld pool during both the laser and the EBW The computed keyhole wall temperatures during EBW at low pressures were lower than those during the LBW at atmospheric pressure for identical heat input

Numerical simulation of heat transfer and fluid flow in GTA/Laser hybrid welding

Abstract: In order to understand the temperature fields, cooling rates and mixing in the weld pool, a comprehensive, three-dimensional heat transfer and fluid flow model is developed and tested by comparing ...

A Convective Heat-Transfer Model for Partial and Full Penetration Keyhole Mode Laser Welding of a Structural Steel

Abstract: In the keyhole mode laser welding of many important engineering alloys such as structural steels, convective heat transport in the weld pool significantly affects temperature fields, cooling rates, and solidification characteristics of welds. Here we present a comprehensive model for understanding these important weld parameters by combining an efficient keyhole model with convective three-dimensional (3-D) heat-transfer calculations in the weld pool for both partial and full penetration laser welds. A modified turbulence model based on Prandtl’s mixing length hypotheses is included to account for the enhanced heat and mass transfer due to turbulence in the weld pool by calculating spatially variable effective values of viscosity and thermal conductivity. The model has been applied to understand experimental results of both partial and full penetration welds of A131 structural steel for a wide range of welding speeds and input laser powers. The experimentally determined shapes of the partial and full penetration keyhole mode laser welds, the temperature profiles, and the solidification profiles are examined using computed results from the model. Convective heat transfer was the main mechanism of heat transfer in the weld pool and affected the weld pool geometry for A131 steel. Calculation of solidification parameters at the trailing edge of the weld pool showed nonplanar solidification with a tendency to become more dendritic with increase in laser power. Free surface calculation showed formation of a hump at the bottom surface of the full penetration weld. The weld microstructure becomes coarser as the heat input per unit length is increased, by either increasing laser power or decreasing welding velocity.

I and i

Abstract: There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality. Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …