Ronald Schade

Bio: Ronald Schade is an academic researcher. The author has contributed to research in topics: Tissue engineering & Sampling (statistics). The author has an hindex of 6, co-authored 12 publications receiving 321 citations.

Antibacterial biodegradable Mg-Ag alloys

Abstract: The use of magnesium alloys as degradable metals for biomedical applications is a topic of ongoing research and the demand for multifunctional materials is increasing. Hence, binary Mg-Ag alloys were designed as implant materials to combine the favourable properties of magnesium with the well-known antibacterial property of silver. In this study, three Mg-Ag alloys, Mg2Ag, Mg4Ag and Mg6Ag that contain 1.87 %, 3.82 % and 6.00 % silver by weight, respectively, were cast and processed with solution (T4) and aging (T6) heat treatment. The metallurgical analysis and phase identification showed that all alloys contained Mg4Ag as the dominant β phase. After heat treatment, the mechanical properties of all Mg-Ag alloys were significantly improved and the corrosion rate was also significantly reduced, due to presence of silver. Mg(OH)₂ and MgO present the main magnesium corrosion products, while AgCl was found as the corresponding primary silver corrosion product. Immersion tests, under cell culture conditions, demonstrated that the silver content did not significantly shift the pH and magnesium ion release. In vitro tests, with both primary osteoblasts and cell lines (MG63, RAW 264.7), revealed that Mg-Ag alloys show negligible cytotoxicity and sound cytocompatibility. Antibacterial assays, performed in a dynamic bioreactor system, proved that the alloys reduce the viability of two common pathogenic bacteria, Staphylococcus aureus (DSMZ 20231) and Staphylococcus epidermidis (DSMZ 3269), and the results showed that the killing rate of the alloys against tested bacteria exceeded 90%. In summary, biodegradable Mg-Ag alloys are cytocompatible materials with adjustable mechanical and corrosion properties and show promising antibacterial activity, which indicates their potential as antibacterial biodegradable implant materials.

Two‐Photon Polymerization of Biocompatible Photopolymers for Microstructured 3D Biointerfaces

Abstract: Three-dimensional microstructured scaffolds provide a means for cells to be cultured in vitro in a way that resembles natural conditions more closely than flat tissue culture polystyrene. In the presented work, two-photon polymerization (2PP) is applied as a tool for the engineering of high-resolution 3D scaffold structures with a well defined microarchitecture made of biocompatible photo resins. 2PP is a novel photolithographic technique using femtosecond laser pulses which enables free 3D microstructuring of liquid photo resins due to the relationship of the axial and lateral spatial confinement of the photoreactiontothefocalvolumeofafocusedlaserbeam.Asetofphotoresinsweretestedwithregardto 2PP processability and three different classes of methacrylated photopolymerizable monomers (methacrylated oligolactones, urethane dimethacrylate, poly(ethylene glycol diacrylate)) were found to be efficient 2PP materials. 3D microstructures based on computer models were produced and tested for biocompatibility. The initial cell adhesion and the viability of bovine chondrocytes on the polymeric scaffolds were evaluated morphologically by confocal laser scanning microscopy (CLSM) after threeday culture on 2PP derived microstructures. 2PP derived scaffolds were fabricated in different sizes and geometries, starting from the 100mm-range reaching out to the cm-range showing the actual possibilities to produce large volume scaffolds even for implantation purposes.

Influence of the Microstructure and Silver Content on Degradation, Cytocompatibility, and Antibacterial Properties of Magnesium-Silver Alloys In Vitro.

Abstract: Implantation is a frequent procedure in orthopedic surgery, particularly in the aging population. However, it possesses the risk of infection and biofilm formation at the surgical site. This can cause unnecessary suffering to patients and burden on the healthcare system. Pure Mg, as a promising metal for biodegradable orthopedic implants, exhibits some antibacterial effects due to the alkaline pH produced during degradation. However, this antibacterial effect may not be sufficient in a dynamic environment, for example, the human body. The aim of this study was to increase the antibacterial properties under harsh and dynamic conditions by alloying silver metal with pure Mg as much as possible. Meanwhile, the Mg-Ag alloys should not show obvious cytotoxicity to human primary osteoblasts. Therefore, we studied the influence of the microstructure and the silver content on the degradation behavior, cytocompatibility, and antibacterial properties of Mg-Ag alloys in vitro. The results indicated that a higher silver content can increase the degradation rate of Mg-Ag alloys. However, the degradation rate could be reduced by eliminating the precipitates in the Mg-Ag alloys via T4 treatment. By controlling the microstructure and increasing the silver content, Mg-Ag alloys obtained good antibacterial properties in harsh and dynamic conditions but had almost equivalent cytocompatibility to human primary osteoblasts as pure Mg.

Synthesis of Photopolymerizable Hydrophilic Macromers and Evaluation of Their Applicability as Reactive Resin Components for the Fabrication of Three-Dimensionally Structured Hydrogel Matrices by 2-Photon-Polymerization**

Abstract: Two-photon polymerization (2-PP) is a promising new photolithographic technique to fabricate three-dimensional (3D), micro- and nano-structured tissue engineering scaffolds from photopolymerizable monomers. Although various photo resins are known for the use in 2-PP, there is currently a need for photo-curable monomers processable by 2-PP to generate biocompatible 3D-structured hydrogel materials for soft or cartilage tissue regeneration. In the present work hydrophilic methacrylate monomers and macromers based on synthetic poly(glycerine) and poly(ethylene glycol) urethanes as well as on the biopolymers dextran and hyaluronan is prepared. The photopolymerization behavior of these substances are investigated and formed hydrogel networks are studied with regard to their mechanical properties, cytocompatibility, and hydrolytic degradation. Based on these examinations simple 3D model structures are fabricated from these photo-curable monomers and macromers by 2-PP. It is shown that both the synthetic monomers and the dextran methacrylate macromer are efficient 2-PP starting materials whereas the hyaluronan methacrylate can be used for 2-PP only in combination with suitable water-soluble co-monomers. No cytotoxic effects are found in preliminary chondrocyte cultivation experiments on 2-PP-fabricated scaffolds but initial cell adhesion on the hydrophilic scaffold surfaces is rather low and has to be further improved to apply these structures in tissue engineering.

Two-photon techniques in tissue engineering.

Abstract: PurposeNIR radiation in the range of about 800 nm is less absorbed by biological tissues and is suited for triggering photonic effects using femtosecond pulsed Ti: Sa lasers. Especially in the life...

Two-photon polymerization initiators for three-dimensional optical data storage and microfabrication

Abstract: Two-photon excitation provides a means of activating chemical or physical processes with high spatial resolution in three dimensions and has made possible the development of three-dimensional fluorescence imaging, optical data storage, and lithographic microfabrication. These applications take advantage of the fact that the two-photon absorption probability depends quadratically on intensity, so under tight-focusing conditions, the absorption is confined at the focus to a volume of order λ3 (where λ is the laser wavelength). Any subsequent process, such as fluorescence or a photoinduced chemical reaction, is also localized in this small volume. Although three-dimensional data storage and microfabrication have been illustrated using two-photon-initiated polymerization of resins incorporating conventional ultraviolet-absorbing initiators, such photopolymer systems exhibit low photosensitivity as the initiators have small two-photon absorption cross-sections (δ). Consequently, this approach requires high laser power, and its widespread use remains impractical. Here we report on a class of π;-conjugated compounds that exhibit large δ (as high as 1, 250 × 10−50 cm4 s per photon) and enhanced two-photon sensitivity relative to ultraviolet initiators. Two-photon excitable resins based on these new initiators have been developed and used to demonstrate a scheme for three-dimensional data storage which permits fluorescent and refractive read-out, and the fabrication of three-dimensional micro-optical and micromechanical structures, including photonic-bandgap-type structures.

Controlling the Porosity and Microarchitecture of Hydrogels for Tissue Engineering

Abstract: Tissue engineering holds great promise for regeneration and repair of diseased tissues, making the development of tissue engineering scaffolds a topic of great interest in biomedical research. Beca...

Photocrosslinking of gelatin macromers to synthesize porous hydrogels that promote valvular interstitial cell function.

Abstract: The development of novel three-dimensional cell culture platforms for the culture of aortic valvular interstitial cells (VICs) has been fraught with many challenges. Although the most tunable, purely synthetic systems have not been successful at promoting cell survivability or function. On the other hand, entirely natural materials lack mechanical integrity. Here we explore a novel hybrid system consisting of gelatin macromers synthetically modified with methacrylate functionalities allowing for photoencapsulation of cells. Scanning electron microscopy observations show a microporous structure induced during polymerization within the hydrogel. This porous structure was tunable with polymerization rate and did not appear to have interconnected pores. Treatment with collagenase caused bulk erosion indicating enzymatic degradation controls the matrix remodeling. VICs, an important cell line for heart valve tissue engineering, were photoencapsulated and examined for cell-directed migration and differentiation. VICs were able to achieve their native morphology within 2 weeks of culture. The addition of the pro-fibrotic growth factor, transforming growth factor-beta1, accelerated this process and also was capable of inducing enhanced alpha-smooth muscle actin and collagen-1 expression, indicating a differentiation from quiescent fibroblasts to active myofibroblasts as demonstrated by quantitative real-time polymerase chain reaction and immunohistochemistry. Although these studies were limited to VICs, this novel hydrogel system may also be useful for studying other fibroblastic cell types.

A review on stereolithography and its applications in biomedical engineering

Abstract: Stereolithography is a solid freeform technique (SFF) that was introduced in the late 1980s Although many other techniques have been developed since then, stereolithography remains one of the most powerful and versatile of all SFF techniques It has the highest fabrication accuracy and an increasing number of materials that can be processed is becoming available In this paper we discuss the characteristic features of the stereolithography technique and compare it to other SFF techniques The biomedical applications of stereolithography are reviewed, as well as the biodegradable resin materials that have been developed for use with stereolithography Finally, an overview of the application of stereolithography in preparing porous structures for tissue engineering is given