S. Jay Chey

Bio: S. Jay Chey is an academic researcher from IBM. The author has contributed to research in topics: Thin film & Scanning tunneling microscope. The author has an hindex of 19, co-authored 58 publications receiving 3235 citations. Previous affiliations of S. Jay Chey include University of Illinois at Urbana–Champaign & Schott AG.

Thin film solar cell with 8.4% power conversion efficiency using an earth‐abundant Cu2ZnSnS4 absorber

Abstract: Using vacuum process, we fabricated Cu2ZnSnS4 solar cells with 8.4% efficiency, a number independently certified by an external, accredited laboratory. This is the highest efficiency reported for pure sulfide Cu2ZnSnS4 prepared by any method. Consistent with literature, the optimal composition is Cu-poor and Zn-rich despite the precipitation of secondary phases (e.g., ZnS). Despite a very thin absorber thickness (~600 nm), a reasonably good short-circuit current was obtained. Time-resolved photoluminescence measurements suggest a minority carrier-diffusion length on the order of several hundreds of nanometers and relatively good collection of photo-carriers across the entire absorber thickness. Copyright © 2011 John Wiley & Sons, Ltd.

Control of an interfacial MoSe2 layer in Cu2ZnSnSe4 thin film solar cells: 8.9% power conversion efficiency with a TiN diffusion barrier

Abstract: We have examined Cu2ZnSnSe4 (CZTSe) solar cells prepared by thermal co-evaporation on Mo-coated glass substrates followed by post-deposition annealing under Se ambient. We show that the control of an interfacial MoSe2 layer thickness and the introduction of an adequate Se partial pressure (PSe) during annealing are essential to achieve high efficiency CZTSe solar cells—a reverse correlation between device performance and MoSe2 thickness is observed, and insufficient PSe leads to the formation of defects within the bandgap as revealed by photoluminescence measurements. Using a TiN diffusion barrier, we demonstrate 8.9% efficiency CZTSe devices with a long lifetime of photo-generated carriers.

12% Efficiency CuIn(Se,S)2 Photovoltaic Device Prepared Using a Hydrazine Solution Process†

Abstract: Thin-film CuIn(Se,S)2 (i.e., CIS) absorbers have been solution-deposited using a hydrazine-based approach that offers the potential to significantly lower the fabrication cost for CIS solar cells. In this method, metal chalcogenides are completely dissolved in hydrazine, forming a homogeneous precursor solution. Film deposition is demonstrated by spin-coating of the precursor solution onto various substrates, including Mo-coated glass and thermally oxidized silicon wafers. Using this approach, no postdeposition anneal in a toxic Se or S-containing environment is needed to obtain CIS films. Instead, only a simple heat-treatment in an inert atmosphere is required, resulting in CIS films with good crystallinity. Bandgap tuning can readily be achieved by varying the amount of S incorporated into the film. Complete CIS devices with glass/Mo/CIS/CdS/i-ZnO/ITO structure are fabricated using absorbers produced via this hydrazine-based approach. Air Mass 1.5G power conversion efficiencies of as high as 12.2% have ...

Prospects of Colloidal Nanocrystals for Electronic and Optoelectronic Applications

Abstract: Nanocrystals (NCs) discussed in this Review are tiny crystals of metals, semiconductors, and magnetic material consisting of hundreds to a few thousand atoms each. Their size ranges from 2-3 to about 20 nm. What is special about this size regime that placed NCs among the hottest research topics of the last decades? The quantum mechanical coupling * To whom correspondence should be addressed. E-mail: dvtalapin@uchicago.edu. † The University of Chicago. ‡ Argonne National Lab. Chem. Rev. 2010, 110, 389–458 389

Efficient organometal trihalide perovskite planar-heterojunction solar cells on flexible polymer substrates

Abstract: Organometal trihalide perovskite solar cells offer the promise of a low-cost easily manufacturable solar technology, compatible with large-scale low-temperature solution processing. Within 1 year of development, solar-to-electric power-conversion efficiencies have risen to over 15%, and further imminent improvements are expected. Here we show that this technology can be successfully made compatible with electron acceptor and donor materials generally used in organic photovoltaics. We demonstrate that a single thin film of the low-temperature solution-processed organometal trihalide perovskite absorber CH3NH3PbI3-xClx, sandwiched between organic contacts can exhibit devices with power-conversion efficiency of up to 10% on glass substrates and over 6% on flexible polymer substrates. This work represents an important step forward, as it removes most barriers to adoption of the perovskite technology by the organic photovoltaic community, and can thus utilize the extensive existing knowledge of hybrid interfaces for further device improvements and flexible processing platforms.

Classification of lattice defects in the kesterite Cu2ZnSnS4 and Cu2ZnSnSe4 earth-abundant solar cell absorbers.

Abstract: The kesterite-structured semiconductors Cu2ZnSnS4 and Cu2ZnSnSe4 are drawing considerable attention recently as the active layers in earth-abundant low-cost thin-film solar cells. The additional number of elements in these quaternary compounds, relative to binary and ternary semiconductors, results in increased flexibility in the material properties. Conversely, a large variety of intrinsic lattice defects can also be formed, which have important influence on their optical and electrical properties, and hence their photovoltaic performance. Experimental identification of these defects is currently limited due to poor sample quality. Here recent theoretical research on defect formation and ionization in kesterite materials is reviewed based on new systematic calculations, and compared with the better studied chalcopyrite materials CuGaSe2 and CuInSe2 . Four features are revealed and highlighted: (i) the strong phase-competition between the kesterites and the coexisting secondary compounds; (ii) the intrinsic p-type conductivity determined by the high population of acceptor CuZn antisites and Cu vacancies, and their dependence on the Cu/(Zn+Sn) and Zn/Sn ratio; (iii) the role of charge-compensated defect clusters such as [2CuZn +SnZn ], [VCu +ZnCu ] and [ZnSn +2ZnCu ] and their contribution to non-stoichiometry; (iv) the electron-trapping effect of the abundant [2CuZn +SnZn ] clusters, especially in Cu2ZnSnS4. The calculated properties explain the experimental observation that Cu poor and Zn rich conditions (Cu/(Zn+Sn) ≈ 0.8 and Zn/Sn ≈ 1.2) result in the highest solar cell efficiency, as well as suggesting an efficiency limitation in Cu2ZnSn(S,Se)4 cells when the S composition is high.

High‐Efficiency Solar Cell with Earth‐Abundant Liquid‐Processed Absorber

Abstract: 2010 WILEY-VCH Verlag Gmb Chalcogenide-based solar cells provide a critical pathway to cost parity between photovoltaic (PV) and conventional energy sources. Currently, only Cu(In,Ga)(S,Se)2 (CIGS) and CdTe technologies have reached commercial module production with stable power conversion efficiencies of over 9 percent. Despite the promise of these technologies, restrictions on heavy metal usage for Cd and limitations in supply for In and Te are projected to restrict the production capacity of the existing chalcogen-based technologies to <100GWp per year, a small fraction of our growing energy needs, which are expected to double to 27 TW by 2050. Earth-abundant copper-zinc-tin-chalcogenide kesterites, Cu2ZnSnS4 and Cu2ZnSnSe4, have been examined as potential alternatives for the two leading technologies, reaching promising but not yet marketable efficiencies of 6.7% and 3.2%, respectively, by multilayer vacuum deposition. Here we show a non-vacuum, slurry-based coating method that combines advantages of both solution processing and particlebased deposition, enabling fabrication of Cu2ZnSn(Se,S)4 devices with over 9.6% efficiency—a factor of five performance improvement relative to previous attempts to use highthroughput ink-based approaches and >40% higher than previous record devices prepared using vacuum-based methods. To address the issue of cost, non-vacuum ‘‘ink’’-based approaches—both from solutions and suspensions—are being developed for chalcogenide-based absorber layer deposition to replace potentially more expensive vacuum-based techniques. True solutions allow intermixing of the constituents at a molecular level and the formation of smooth homogeneous films, as demonstrated with spin-coated CIGS absorber layers from hydrazine (N2H4) solutions. [11–13] The chemically reducing character of hydrazine stabilizes solutions of anions with direct metal-chalcogen bonding for select elements (e.g. Cu, In, Ga, Sn), without the necessity to introduce typical impurities (e.g., C, O, Cl). Suspension approaches employ solid particles designed to be deposited on a substrate and reacted or fused with each other, to form a desired crystalline phase and grain structure. Normally insoluble components can be deposited by this approach using typical liquid-based deposition (e.g., printing, spin coating, slit casting, spraying). Although high-quality large-grained absorber layers can be formed for selected systems using either solutionor particlebased deposition, numerous challenges confront each approach for more general deposition needs. Solution processing is limited by the solubility of many materials of interest (e.g., ZnSe1–xSx in hydrazine solvents—relevant for the deposition of Cu2ZnSnS4 or Cu2ZnSnSe4). In addition, volume contraction upon drying of solution-deposited layers creates stress in the film that may cause crack formation in thicker films. In suspension approaches, a common difficulty is achieving single-phase crystallization among the solid particles. Particle-based approaches (as well as some solution methods) typically require the addition of organic agents to improve wetting and particle dispersion, and to avoid film cracks and delamination. Most of these non-volatile organic additives introduce carbon contamination in the final layer. Because of these challenges, vacuum-based techniques have historically shown superior performance to liquid coating. In the case of the earth-abundant Cu2ZnSn(S,Se)4 materials, ink-based approaches have to date yielded at most <1.6% efficiency devices. Here we demonstrate an hybrid solution-particle approach, using the earth-abundant Cu2ZnSn(S,Se)4 system as an example, which enables fabrication of PV devices with over 9.6% power conversion efficiency. The slurry (or ink) employed for deposition comprises a Cu–Sn chalcogenide (S or S–Se) solution in hydrazine (see Experimental section), with the in situ formation of readily dispersible particle-based Zn-chalcogenide precursors, ZnSe(N2H4) (Figure 1a,d) or ZnS(N2H4) (Figure 1b). Thermogravimetric analysis (TGA) of the isolated selenide particle precursor shows decomposition at approximately 200 8C, with mass loss of about 20%, close to the theoretical value expected upon transition to pure ZnSe (Figure 1c,d). Deposition using this hybrid slurry successfully combines the advantages of solution and suspension deposition routes by use of solutions containing solid particles, wherein both components (i.e., solution and particle) contain metal and chalcogen elements that integrate into the final film. Using the hybrid slurry method (i) solubility limitations are resolved, as virtually any materials system can be constituted by a combination of solid and dissolved components; (ii) the dissolved components can be engineered as an efficient binding media for the particles, eliminating the need of separate organic binders; (iii) solid particles act as stress-relief and crack-deflection centers allowing the deposition of thicker layers than pure solution processes; and (iv) the intimate contact between the two phases allows rapid reaction and homogeneous phase formation. Complete conversion of all constituents of the spin-coated hybrid precursor films into a single-phase, highly crystalline Cu2ZnSn(S,Se)4 is achieved by annealing at 540 8C on a hot plate. Three main types of samples were targeted – high selenium content (A), intermediate sulfoselenide (B) and pure sulfide (C) –