Sadri Sen

Bio: Sadri Sen is an academic researcher from Atatürk University. The author has contributed to research in topics: Finite element method & Elastic modulus. The author has an hindex of 16, co-authored 40 publications receiving 898 citations. Previous affiliations of Sadri Sen include University of Texas at El Paso.

Studies on the influence of chloride ion concentration and pH on the corrosion and electrochemical behaviour of AZ63 magnesium alloy

Abstract: Magnesium-based light alloys belong to a class of structural materials with increasing industrial attention. Magnesium alloys show the lowest density among the engineering metallic materials, low cost and large availability. As a consequence, this light alloys have a promising future. The paper presented reveals the influence of chloride ion concentration and pH on the corrosion and electrochemical behavior of AZ63 magnesium alloy in NaCl solution. The experimental techniques used include immersion studies and potentiodynamic polarization tests. The corrosion rate was very high in highly acidic solutions (pH 2) as compared to that in other solutions. The corrosion rate usually increased with the decrease in pH and the increase in chloride ion concentration. But the quantity of the increase in corrosion rate was different at separate pH and concentration regions. The corrosion potential usually shifted to more negative values with the increase in concentration of chloride ions and the decrease in pH of solution.

The effect of DC magnetron sputtering AlN coatings on the corrosion behaviour of magnesium alloys

Abstract: Magnesium and its alloys are susceptible to corrosion, which has limited their use in the automotive and aerospace industries, where low weight is of significant concern. In this study, AlN films were coated on the magnesium alloys (AZ31, AZ61, AZ63, and AZ91) using physical vapour deposition (PVD) technique of DC magnetron sputtering, and the influence of the coating on the corrosion behaviour of the magnesium alloys was examined. A physical vapour deposition (PVD) system for coating processes, a potentiostat for electrochemical corrosion tests, X-ray difractometer (XRD) for compositional analysis of coating, and scanning electron microscopy (SEM) for surface examinations were used. It was found that DC magnetron sputtering AlN coatings deposited on magnesium alloys increased the corrosion resistance of these alloys. However, the basis factor determining the ability of protection from corrosion was that small structural defects in the coating, e.g., pores, pinholes, cracks that could arise from the coating process or substrate.

Finite element analysis of mechanical behavior, permeability and fluid induced wall shear stress of high porosity scaffolds with gyroid and lattice-based architectures.

Abstract: Scaffold design necessitates the consideration of mechanical properties and fluid flow dynamics as the main factors in the development of such materials. The mechanical behavior of bone scaffolds is characterized by properties such as elastic modulus and compressive strength. In terms of fluid flow dynamics, within bone scaffolds, permeability is an important parameter that affects cells' biological activities, and flow-induced shear stress is used as a mechanical stimulant of cell growth. In this study, two scaffold architectures with gyroid and lattice-based rectangular unit cells were designed to analysis the effective elastic moduli, compressive strength, permeability and fluid flow-induced wall shear stress as functions of porosity. Six levels of porosity (65%, 70%, 75%, 80%, 85% and 90%) were assigned to the scaffold architectures, and 12 models were developed. Scaffold deformation under static loading, compressive strength based on von Mises criteria, pressure drop, and fluid flow-induced wall shear stress in the scaffolds were then determined by finite element analysis. In both the scaffold types, models with higher porosity exhibited lower mechanical properties. Under the same porosity, the lattice-based scaffolds exhibited a Young's modulus and a compressive strength higher than those achieved by the gyroid scaffolds. With reference to geometrical parameters and the derived pressure drop from the computational fluid dynamics (CFD) analysis, scaffolds permeability was calculated using Darcy's law. In both the scaffold architectures, high porosity increased permeability and decreased wall shear stress. In the same porosity, the lattice-based models exhibited higher permeability and lower wall shear stress than did the gyroid models. On the basis of the results on elastic modulus and permeability, the models that most effectively mimic the properties of cancellous bones were identified.

The effect of PVD coatings on the corrosion behaviour of AZ91 magnesium alloy

Abstract: In this study, multilayered AlN (AlN + AlN + AlN) and AlN + TiN were coated on AZ91 magnesium alloy using physical vapour deposition (PVD) technique of DC magnetron sputtering, and the influence of the coatings on the corrosion behaviour of the AZ91 alloy was examined. A PVD system for coating processes, a potentiostat for electrochemical corrosion tests, X-ray difractometer for compositional analysis of the coatings, and scanning electron microscopy for surface examinations were used. It was determined that PVD coatings deposited on AZ91 magnesium alloy increased the corrosion resistance of the alloy, and AlN + AlN + AlN coating increased the corrosion resistance much more than AlN + TiN coating. However, it was observed that, in the coating layers, small structural defects e.g., pores, pinholes, cracks that could arise from the coating process or substrate and get the ability of protection from corrosion worsened were present.

The effect of PVD coatings on the wear behaviour of magnesium alloys

Abstract: In this study, AlN/TiN was coated on magnesium alloys using physical vapour deposition (PVD) technique of DC magnetron sputtering, and the influence of the coating on the wear behaviour of the alloys was examined. A physical vapour deposition system for coating processes, a reciprocating wear system for wear tests, a universal hardness equipment for hardness measurement, a X-ray diffractometer (XRD) for compositional analysis of the coating, and a scanning electron microscopy (SEM) for surface examinations were used. It was determined that the wear resistance of the magnesium alloys can be increased by PVD coatings. However, small structural defects which could arise from the coating process or substrate were observed in the coating layers.

Fast parallel algorithms for short-range molecular dynamics

Abstract: Three parallel algorithms for classical molecular dynamics are presented. The first assigns each processor a fixed subset of atoms; the second assigns each a fixed subset of inter-atomic forces to compute; the third assigns each a fixed spatial region. The algorithms are suitable for molecular dynamics models which can be difficult to parallelize efficiently—those with short-range forces where the neighbors of each atom change rapidly. They can be implemented on any distributed-memory parallel machine which allows for message-passing of data between independently executing processors. The algorithms are tested on a standard Lennard-Jones benchmark problem for system sizes ranging from 500 to 100,000,000 atoms on several parallel supercomputers--the nCUBE 2, Intel iPSC/860 and Paragon, and Cray T3D. Comparing the results to the fastest reported vectorized Cray Y-MP and C90 algorithm shows that the current generation of parallel machines is competitive with conventional vector supercomputers even for small problems. For large problems, the spatial algorithm achieves parallel efficiencies of 90% and a 1840-node Intel Paragon performs up to 165 faster than a single Cray C9O processor. Trade-offs between the three algorithms and guidelines for adapting them to more complex molecular dynamics simulations are also discussed.

Microstructure, mechanical and corrosion properties and biocompatibility of Mg-Zn-Mn alloys for biomedical application

Abstract: Mn and Zn were selected to develop a Mg-Zn-Mn magnesium alloy for biomedical application due to the good biocompatibility of Zn and Mn elements. Microstructure, mechanical properties, corrosion properties and biocompatibility of the Mg-Zn-Mn alloys have been investigated by use of optical microscope, scanning electron microscope, tensile testing, and blood hemolysis and cell toxicity. Microstructure observation has shown that the addition of Zn and the extrusion significantly refined the grain size of both the as-cast and the extruded magnesium alloys, which mainly contributes to the high tensile strength and good elongation. Polarization test has shown Zn could accelerate the formation of a passivation film, which provides good protection to the magnesium alloy against simulate body fluid. Cell culture and hemolysis tests have shown that the magnesium alloy did not have cell toxicity, showing good cytocompatibility, but the alloy caused hemolysis to blood system. It was suggested that surface modification have to be adopted to improve the blood compatibility of the magnesium alloy for the application in blood environment. (C) 2008 Elsevier B.V. All rights reserved.

Electrochemical corrosion behavior of composite coatings of sealed MAO film on magnesium alloy AZ91D

Abstract: Protective composite coatings were prepared on magnesium alloy AZ91D by micro-arc oxidation (MAO) treatment plus a top coating with sealing agent using multi-immersion technique under low-pressure conditions. The corrosion resistance of AZ91D alloy with composite coatings was superior evidently to that with merely MAO film. SEM observations revealed that the sealing agent was integrated with MAO film by physically interlocking; therewith covered uniformly the surface as well as penetrated into pores and rnicro-cracks of MAO film. The anti-corrosion properties in 3.5% NaCl solution of the composite coatings were evaluated by using electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization measurements. Based on the results of chronopotentiometric (E similar to t) and EIS measurements for long time immersion in 3.5% NaCl solution, appropriate equivalent circuits for the composite coatings system were proposed. It follows that due to the blocking effect of the sealing agent in pores and cracks in MAO film, the composite coatings can suppress the corrosion process by holding back the transfer or diffusion of electrolyte and corrosion products between the composite coatings and solution during immersion. (c) 2005 Elsevier Ltd. All rights reserved.

Influence of pH and chloride ion concentration on the corrosion of Mg alloy ZE41

Abstract: The influence of pH and chloride ion concentration on the corrosion behaviour of ZE41 was studied using immersion tests and electrochemical measurements. A shorter incubation period to the onset of corrosion; a more negative corrosion potential; and a higher corrosion rate correlated with a higher chloride ion concentration at each pH value and correlated with a lower pH value for each chloride ion concentration. This corrosion behaviour is consistent with the current understanding that the corrosion behaviour of magnesium alloys is governed by a partially protective surface film, with the corrosion reactions occurring predominantly at the breaks or imperfections of the partially protective film. The implication is that the fraction of film free surface increases with decreasing bulk pH and with increasing chloride ion concentration. This is consistent with the known tendency of chloride ions to cause film breakdown and the known instability of Mg(OH)2 in solutions with pH less than 10.5. The electrochemical measurements of the corrosion rate, based on the corrosion current at the free corrosion potential, did not agree with direct measurements evaluated from the evolved hydrogen, in agreement with other observations for Mg.

Effect of electrolyte additives on performance of plasma electrolytic oxidation films formed on magnesium alloy AZ91D

Abstract: Various plasma electrolytic oxidation (PEO) films were prepared on magnesium alloy AZ91D in a silicate bath with different additives such as phosphate, fluoride and borate. Effects of the additives on chemical composition and corrosion resistance of the PEO films were examined by means of scanning electron microscopy (SEM), potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in 3.5% NaCl solution. The results showed that the PEO films obtained in solutions with both borate and fluoride had better corrosion resistance. In order to understand the corrosion mechanism of PEO films on magnesium alloy AZ91D, electronic property of the magnesium electrode with PEO films was studied by Mott–Schottky approach in a solution containing borate and chloride. The results indicated that magnesium electrodes with and without PEO films all exhibited n-type semiconducting property. However, in comparison with the magnesium electrode treated in solutions containing phosphate or borate, the electrode treated in solutions containing both borate and fluoride (M-film) had lower donor concentration and much negative flat band potential; therefore, the M-film had lower reactivity and higher corrosion resistance.