scispace - formally typeset
Search or ask a question
Author

Sergey Lamansky

Other affiliations: Murphy Oil
Bio: Sergey Lamansky is an academic researcher from University of Southern California. The author has contributed to research in topics: Phosphorescence & Phosphorescent organic light-emitting diode. The author has an hindex of 14, co-authored 26 publications receiving 11684 citations. Previous affiliations of Sergey Lamansky include Murphy Oil.

Papers
More filters
Journal ArticleDOI
TL;DR: In this paper, the performance of an organic light-emitting device employing the green electrophosphorescent material, fac tris(2-phenylpyridine) iridium [Ir(ppy)3] doped into a 4,4′-N,N′-dicarbazole-biphenyl host was described.
Abstract: We describe the performance of an organic light-emitting device employing the green electrophosphorescent material, fac tris(2-phenylpyridine) iridium [Ir(ppy)3] doped into a 4,4′-N,N′-dicarbazole-biphenyl host. These devices exhibit peak external quantum and power efficiencies of 8.0% (28 cd/A) and 31 lm/W, respectively. At 100 cd/m2, the external quantum and power efficiencies are 7.5% (26 cd/A) and 19 lm/W at an operating voltage of 4.3 V. This performance can be explained by efficient transfer of both singlet and triplet excited states in the host to Ir(ppy)3, leading to a high internal efficiency. In addition, the short phosphorescent decay time of Ir(ppy)3 (<1 μs) reduces saturation of the phosphor at high drive currents, yielding a peak luminance of 100 000 cd/m2.

3,594 citations

Journal ArticleDOI
TL;DR: The synthesis and photophysical study of a family of cyclometalated iridium(III) complexes are reported, and three of the C(**)N2Ir(acac) complexes were used as dopants for organic light emitting diodes (OLEDs) and show some of the highest efficiencies reported for organic Light Emitting Diodes.
Abstract: The synthesis and photophysical study of a family of cyclometalated iridium(III) complexes are reported. The iridium complexes have two cyclometalated (C∧N) ligands and a single monoanionic, bidentate ancillary ligand (LX), i.e., C∧N2Ir(LX). The C∧N ligands can be any of a wide variety of organometallic ligands. The LX ligands used for this study were all β-diketonates, with the major emphasis placed on acetylacetonate (acac) complexes. The majority of the C∧N2Ir(acac) complexes phosphoresce with high quantum efficiencies (solution quantum yields, 0.1−0.6), and microsecond lifetimes (e.g., 1−14 μs). The strongly allowed phosphorescence in these complexes is the result of significant spin−orbit coupling of the Ir center. The lowest energy (emissive) excited state in these C∧N2Ir(acac) complexes is a mixture of 3MLCT and 3(π−π*) states. By choosing the appropriate C∧N ligand, C∧N2Ir(acac) complexes can be prepared which emit in any color from green to red. Simple, systematic changes in the C∧N ligands, whic...

2,655 citations

Journal ArticleDOI
TL;DR: The synthesis, electrochemistry, and photophysics of a series of square planar Pt(II) complexes are reported, with well-resolved vibronic fine structure observed in all of the emission spectra.
Abstract: The synthesis, electrochemistry, and photophysics of a series of square planar Pt(II) complexes are reported. The complexes have the general structure C∧NPt(O∧O),where C∧N is a monoanionic cyclometalating ligand (e.g., 2-phenylpyridyl, 2-(2‘-thienyl)pyridyl, 2-(4,6-difluorophenyl)pyridyl, etc.) and O∧O is a β-diketonato ligand. Reaction of K2PtCl4 with a HC∧N ligand precursor forms the chloride-bridged dimer, C∧NPt(μ-Cl)2PtC∧N, which is cleaved with β-diketones such as acetyl acetone (acacH) and dipivaloylmethane (dpmH) to give the corresponding monomeric C∧NPt(O∧O) complex. The thpyPt(dpm) (thpy = 2-(2‘-thienyl)pyridyl) complex has been characterized using X-ray crystallography. The bond lengths and angles for this complex are similar to those of related cyclometalated Pt complexes. There are two independent molecular dimers in the asymmetric unit, with intermolecular spacings of 3.45 and 3.56 A, consistent with moderate π−π interactions and no evident Pt−Pt interactions. Most of the C∧NPt(O∧O) complexes...

1,354 citations

Journal ArticleDOI
TL;DR: The synthesis, structures, electrochemistry, and photophysics of a series of facial (fac) and meridional (mer) tris-cyclometalated Ir(III) complexes are reported, and the HOMO levels are a mixture of Ir and ligand orbitals, while the LUMO is predominantly ligand-based.
Abstract: The synthesis, structures, electrochemistry, and photophysics of a series of facial (fac) and meridional (mer) tris-cyclometalated Ir(III) complexes are reported. The complexes have the general formula Ir(C'N)(3) [where C'N is a monoanionic cyclometalating ligand; 2-phenylpyridyl (ppy), 2-(p-tolyl)pyridyl (tpy), 2-(4,6-difluorophenyl)pyridyl (46dfppy), 1-phenylpyrazolyl (ppz), 1-(4,6-difluorophenyl)pyrazolyl (46dfppz), or 1-(4-trifluoromethylphenyl)pyrazolyl (tfmppz)]. Reaction of the dichloro-bridged dimers [(C'N(2)Ir(mu-Cl)(2)Ir(C'N)(2)] with 2 equiv of HC( wedge )N at 140-150 degrees C forms the corresponding meridional isomer, while higher reaction temperatures give predominantly the facial isomer. Both facial and meridional isomers can be obtained in good yield (>70%). The meridional isomer of Ir(tpy)(3) and facial and meridional isomers of Ir(ppz)(3) and Ir(tfmppz)(3) have been structurally characterized using X-ray crystallography. The facial isomers have near identical bond lengths (av Ir-C = 2.018 A, av Ir-N = 2.123 A) and angles. The three meridional isomers have the expected bond length alternations for the differing trans influences of phenyl and pyridyl/pyrazolyl ligands. Bonds that are trans to phenyl groups are longer (Ir-C av = 2.071 A, Ir-N av = 2.031 A) than when they are trans to heterocyclic groups. The Ir-C and Ir-N bonds with trans N and C, respectively, have bond lengths very similar to those observed for the corresponding facial isomers. DFT calculations of both the singlet (ground) and the triplet states of the compounds suggest that the HOMO levels are a mixture of Ir and ligand orbitals, while the LUMO is predominantly ligand-based. All of the complexes show reversible oxidation between 0.3 and 0.8 V, versus Fc/Fc(+). The meridional isomers are easier to oxidize by ca. 50-100 mV. The phenylpyridyl-based complexes have reduction potentials between -2.5 and -2.8 V, whereas the phenylpyrazolyl-based complexes exhibit no reduction up to the solvent limit of -3.0 V. All of the compounds have intense absorption bands in the UV region assigned into (1)(pi --> pi) transitions and weaker MLCT (metal-to-ligand charge transfer) transitions that extend to the visible region. The MLCT transitions of the pyrazolyl-based complexes are hypsochromically shifted relative to those of the pyridyl-based compounds. The phenylpyridyl-based Ir(III) tris-cyclometalates exhibit intense emission both at room temperature and at 77 K, whereas the phenylpyrazolyl-based derivatives emit strongly only at 77 K. The emission energies and lifetimes of the phenylpyridyl-based complexes (450-550 nm, 2-6 micros) and phenylpyrazolyl-based compounds (390-440 nm, 14-33 micros) are characteristic for a mixed ligand-centered/MLCT excited state. The meridional isomers for both pyridyl and pyrazolyl-based cyclometalates show markedly different spectroscopic properties than do the facial forms. Isolated samples of mer-Ir(C( wedge )N)(3) complexes can be thermally and photochemically converted to facial forms, indicating that the meridional isomers are kinetically favored products. The lower thermodynamic stabilities of the meridional isomers are likely related to structural features of these complexes; that is, the meridional configuration places strongly trans influencing phenyl groups opposite each other, whereas all three phenyl groups are opposite pyridyl or pyrazolyl groups in the facial complexes. The strong trans influence of the phenyl groups in the meridional isomers leads to the observation that they are easier to oxidize, exhibit broad, red-shifted emission, and have lower quantum efficiencies than their facial counterparts.

1,161 citations

Journal ArticleDOI
TL;DR: In this article, the authors demonstrate high-efficiency red electrophosphorescent organic light-emitting devices employing bis(2′-benzo[4,5-a]thienyl)pyridinato-N,C3′) iridium(acetylacetonate) [Btp2Ir(acac)] as a red phosphor.
Abstract: We demonstrate high-efficiency red electrophosphorescent organic light-emitting devices employing bis(2-(2′-benzo[4,5-a]thienyl)pyridinato-N,C3′) iridium(acetylacetonate) [Btp2Ir(acac)] as a red phosphor. A maximum external quantum efficiency of ηext=(7.0±0.5)% and power efficiency of ηp=(4.6±0.5) lm/W are achieved at a current density of J=0.01 mA/cm2. At a higher current density of J=100 mA/cm2, ηext=(2.5±0.3)% and ηp=(0.56±0.05) lm/W are obtained. The electroluminescent spectrum has a maximum at a wavelength of λmax=616 nm with additional intensity peaks at λsub=670 and 745 nm. The Commission Internationale de L’Eclairage coordinates of (x=0.68, y=0.32) are close to meeting video display standards. The short phosphorescence lifetime (∼4 μs) of Btp2Ir(acac) leads to a significant improvement in ηext at high currents as compared to the previously reported red phosphor, 2,3,7,8,12,13,17,18-octaethyl-12H, 23H-prophine platinum (II) PtOEP with a lifetime of ∼50 μs.

822 citations


Cited by
More filters
Journal ArticleDOI
13 Dec 2012-Nature
TL;DR: A class of metal-free organic electroluminescent molecules in which the energy gap between the singlet and triplet excited states is minimized by design, thereby promoting highly efficient spin up-conversion from non-radiative triplet states to radiative singlet states while maintaining high radiative decay rates.
Abstract: The inherent flexibility afforded by molecular design has accelerated the development of a wide variety of organic semiconductors over the past two decades. In particular, great advances have been made in the development of materials for organic light-emitting diodes (OLEDs), from early devices based on fluorescent molecules to those using phosphorescent molecules. In OLEDs, electrically injected charge carriers recombine to form singlet and triplet excitons in a 1:3 ratio; the use of phosphorescent metal-organic complexes exploits the normally non-radiative triplet excitons and so enhances the overall electroluminescence efficiency. Here we report a class of metal-free organic electroluminescent molecules in which the energy gap between the singlet and triplet excited states is minimized by design, thereby promoting highly efficient spin up-conversion from non-radiative triplet states to radiative singlet states while maintaining high radiative decay rates, of more than 10(6) decays per second. In other words, these molecules harness both singlet and triplet excitons for light emission through fluorescence decay channels, leading to an intrinsic fluorescence efficiency in excess of 90 per cent and a very high external electroluminescence efficiency, of more than 19 per cent, which is comparable to that achieved in high-efficiency phosphorescence-based OLEDs.

5,297 citations

Journal ArticleDOI
TL;DR: In this paper, the authors demonstrate very high efficiency electrophosphorescence in organic light-emitting devices employing a phosphorescent molecule doped into a wide energy gap host, achieving a maximum external quantum efficiency of 19.0±1.0 and luminous power efficiency of 60±5 lm/W.
Abstract: We demonstrate very high efficiency electrophosphorescence in organic light-emitting devices employing a phosphorescent molecule doped into a wide energy gap host. Using bis(2-phenylpyridine)iridium(III) acetylacetonate [(ppy)2Ir(acac)] doped into 3-phenyl-4(1′-naphthyl)-5-phenyl-1,2,4-triazole, a maximum external quantum efficiency of (19.0±1.0)% and luminous power efficiency of (60±5) lm/W are achieved. The calculated internal quantum efficiency of (87±7)% is supported by the observed absence of thermally activated nonradiative loss in the photoluminescent efficiency of (ppy)2Ir(acac). Thus, very high external quantum efficiencies are due to the nearly 100% internal phosphorescence efficiency of (ppy)2Ir(acac) coupled with balanced hole and electron injection, and triplet exciton confinement within the light-emitting layer.

3,302 citations

Journal ArticleDOI
TL;DR: The synthesis and photophysical study of a family of cyclometalated iridium(III) complexes are reported, and three of the C(**)N2Ir(acac) complexes were used as dopants for organic light emitting diodes (OLEDs) and show some of the highest efficiencies reported for organic Light Emitting Diodes.
Abstract: The synthesis and photophysical study of a family of cyclometalated iridium(III) complexes are reported. The iridium complexes have two cyclometalated (C∧N) ligands and a single monoanionic, bidentate ancillary ligand (LX), i.e., C∧N2Ir(LX). The C∧N ligands can be any of a wide variety of organometallic ligands. The LX ligands used for this study were all β-diketonates, with the major emphasis placed on acetylacetonate (acac) complexes. The majority of the C∧N2Ir(acac) complexes phosphoresce with high quantum efficiencies (solution quantum yields, 0.1−0.6), and microsecond lifetimes (e.g., 1−14 μs). The strongly allowed phosphorescence in these complexes is the result of significant spin−orbit coupling of the Ir center. The lowest energy (emissive) excited state in these C∧N2Ir(acac) complexes is a mixture of 3MLCT and 3(π−π*) states. By choosing the appropriate C∧N ligand, C∧N2Ir(acac) complexes can be prepared which emit in any color from green to red. Simple, systematic changes in the C∧N ligands, whic...

2,655 citations

Journal ArticleDOI
TL;DR: A summary of the technical advances that are incorporated in the fourth major release of the Q-Chem quantum chemistry program is provided in this paper, covering approximately the last seven years, including developments in density functional theory and algorithms, nuclear magnetic resonance (NMR) property evaluation, coupled cluster and perturbation theories, methods for electronically excited and open-shell species, tools for treating extended environments, algorithms for walking on potential surfaces, analysis tools, energy and electron transfer modelling, parallel computing capabilities, and graphical user interfaces.
Abstract: A summary of the technical advances that are incorporated in the fourth major release of the Q-Chem quantum chemistry program is provided, covering approximately the last seven years. These include developments in density functional theory methods and algorithms, nuclear magnetic resonance (NMR) property evaluation, coupled cluster and perturbation theories, methods for electronically excited and open-shell species, tools for treating extended environments, algorithms for walking on potential surfaces, analysis tools, energy and electron transfer modelling, parallel computing capabilities, and graphical user interfaces. In addition, a selection of example case studies that illustrate these capabilities is given. These include extensive benchmarks of the comparative accuracy of modern density functionals for bonded and non-bonded interactions, tests of attenuated second order Moller–Plesset (MP2) methods for intermolecular interactions, a variety of parallel performance benchmarks, and tests of the accuracy of implicit solvation models. Some specific chemical examples include calculations on the strongly correlated Cr_2 dimer, exploring zeolite-catalysed ethane dehydrogenation, energy decomposition analysis of a charged ter-molecular complex arising from glycerol photoionisation, and natural transition orbitals for a Frenkel exciton state in a nine-unit model of a self-assembling nanotube.

2,396 citations

Journal ArticleDOI
TL;DR: School of Chemistry, Bio21 Institute, University of Melbourne, 30 Flemington Road, Victoria 3010, Australia; School of Materials Science and Engineering, Nanyang Technological University, Nastyang Avenue, Republic of Singapore 639798; Institute of Materials Research and Engineering (IMRE) and the Agency for Science, Technology and Research (A*STAR), 3 Research Link, Singapore 117602.
Abstract: A review was presented to demonstrate a historical description of the synthesis of light-emitting conjugated polymers for applications in electroluminescent devices. Electroluminescence (EL) was first reported in poly(para-phenylene vinylene) (PPV) in 1990 and researchers continued to make significant efforts to develop conjugated materials as the active units in light-emitting devices (LED) to be used in display applications. Conjugated oligomers were used as luminescent materials and as models for conjugated polymers in the review. Oligomers were used to demonstrate a structure and property relationship to determine a key polymer property or to demonstrate a technique that was to be applied to polymers. The review focused on demonstrating the way polymer structures were made and the way their properties were controlled by intelligent and rational and synthetic design.

2,378 citations