Seung-Ki Sul

Bio: Seung-Ki Sul is an academic researcher from Seoul National University. The author has contributed to research in topics: Torque & Inverter. The author has an hindex of 84, co-authored 560 publications receiving 22490 citations. Previous affiliations of Seung-Ki Sul include University of Wisconsin-Madison.

New direct torque control of induction motor for minimum torque ripple and constant switching frequency

Abstract: In this paper, a direct torque control (DTC) method of an induction machine is proposed which enables the minimum torque ripple control, while maintaining constant switching frequency. Some drawbacks of the conventional DTC are the relatively large torque ripple in a low speed range and the variation of switching frequency according to the amplitude of hysteresis bands and the motor operating speed. In the proposed strategy, an RMS torque-ripple equation is derived using instantaneous torque equations and, at each switching cycle, an optimal switching instant which satisfies the minimum torque-ripple condition is determined based on the ripple equation. The proposed strategy improves the performance of the DTC by combining a low-torque-ripple characteristic in steady state with the fast torque dynamics. Experimental results prove the feasibility of the proposed strategy as compared with the conventional method.

Sensorless drive of surface-mounted permanent-magnet motor by high-frequency signal injection based on magnetic saliency

Abstract: This paper presents a new sensorless control scheme of a surface-mounted permanent-magnet (SMPM) motor using high-frequency voltage signal injection method based on the high-frequency impedance difference. In the SMPM motor, due to the flux of the permanent magnet, the stator core around the q-axis winding is saturated. This makes the magnetic saliency in the motor. This magnetic saliency has the information about the rotor position. The high-frequency voltage signal is injected into the motor in order to detect the magnetic saliency and estimate the rotor position. In this paper, the relationship between the high-frequency voltages and high-frequency currents is developed using the voltage equations at the high frequency, and the high-frequency impedance characteristics are analyzed experimentally under various conditions. The proposed sensorless control scheme makes it possible to drive the SMPM motor in the low-speed region including zero speed, even under heavy load conditions. The experimental results verify the performance of the proposed sensorless algorithm.

Speed sensorless vector control of induction motor using extended Kalman filter

Abstract: A vector control of an induction motor by an estimated speed using an extended Kalman filter is proposed. With this method, the states are composed of stator current and rotor flux. The rotor speed is regarded as a parameter, and the composite states consist of the original states and the rotor speed. The extended Kalman filter is employed to identify the speed of an induction motor and rotor flux based on the measured quantities such as stator currents and DC link voltage. The estimated speed is used for vector control and overall speed control. Since the current control is performed at a synchronous rotating reference frame, the estimated speed information is also used for the reference frame transformation of the current controller. Computer simulations and experiments of the speed control have been carried out to test the usefulness of the speed estimation algorithm. The experimental results show that the performance of the speed estimation is very good. >

Inverter output voltage synthesis using novel dead time compensation

Abstract: In this paper, a novel dead time compensation method is presented that produces inverter output voltages equal to reference voltages. An experimental result is also presented to demonstrate the validity of the proposed method. It shows that the compensation of the dead time is possible up to a sub-microsecond range. Also, the reference voltage can be used as a feedback value, which is essential for sensorless vector control and flux estimation. The method is based on space vector pulsewidth modulation (PWM) strategy and it can be carried out automatically by an inverter controller for initial setup without any extra hardware.

Sensorless field orientation control of an induction machine by high frequency signal injection

Abstract: This paper describes a new scheme to find the rotor flux angle from stator voltages and currents by injecting a high-frequency signal. The signal is not a rotating one but a fluctuating one at a reference frame rotating synchronously to the fundamental stator frequency. When the estimated rotor flux angle coincides with the actual angle, the proposed method makes virtually no ripple torque, no vibration and less audible noise caused by the injected signal. The difference of impedances between the flux axis and the quadrature axis at high-frequency signal injection on the rotor flux angle is explained by the equivalent circuit equation of the induction machine. The difference is verified by experiments on test motors under various testing conditions. A sensorless field orientation algorithm is proposed and experimental results clarify the satisfactory operation of the algorithm with one hundred and fifty percent load torque at zero stator frequency.

Overview of Control and Grid Synchronization for Distributed Power Generation Systems

Abstract: Renewable energy sources like wind, sun, and hydro are seen as a reliable alternative to the traditional energy sources such as oil, natural gas, or coal. Distributed power generation systems (DPGSs) based on renewable energy sources experience a large development worldwide, with Germany, Denmark, Japan, and USA as leaders in the development in this field. Due to the increasing number of DPGSs connected to the utility network, new and stricter standards in respect to power quality, safe running, and islanding protection are issued. As a consequence, the control of distributed generation systems should be improved to meet the requirements for grid interconnection. This paper gives an overview of the structures for the DPGS based on fuel cell, photovoltaic, and wind turbines. In addition, control structures of the grid-side converter are presented, and the possibility of compensation for low-order harmonics is also discussed. Moreover, control strategies when running on grid faults are treated. This paper ends up with an overview of synchronization methods and a discussion about their importance in the control

Ultracapacitors: Why, How, and Where is the Technology

Abstract: The science and technology of ultracapacitors are reviewed for a number of electrode materials, including carbon, mixed metal oxides, and conducting polymers. More work has been done using microporous carbons than with the other materials and most of the commercially available devices use carbon electrodes and an organic electrolytes. The energy density of these devices is 3¯5 Wh/kg with a power density of 300¯500 W/kg for high efficiency (90¯95%) charge/discharges. Projections of future developments using carbon indicate that energy densities of 10 Wh/kg or higher are likely with power densities of 1¯2 kW/kg. A key problem in the fabrication of these advanced devices is the bonding of the thin electrodes to a current collector such the contact resistance is less than 0.1 cm2. Special attention is given in the paper to comparing the power density characteristics of ultracapacitors and batteries. The comparisons should be made at the same charge/discharge efficiency.

Review of Battery Charger Topologies, Charging Power Levels, and Infrastructure for Plug-In Electric and Hybrid Vehicles

Abstract: This paper reviews the current status and implementation of battery chargers, charging power levels, and infrastructure for plug-in electric vehicles and hybrids. Charger systems are categorized into off-board and on-board types with unidirectional or bidirectional power flow. Unidirectional charging limits hardware requirements and simplifies interconnection issues. Bidirectional charging supports battery energy injection back to the grid. Typical on-board chargers restrict power because of weight, space, and cost constraints. They can be integrated with the electric drive to avoid these problems. The availability of charging infrastructure reduces on-board energy storage requirements and costs. On-board charger systems can be conductive or inductive. An off-board charger can be designed for high charging rates and is less constrained by size and weight. Level 1 (convenience), Level 2 (primary), and Level 3 (fast) power levels are discussed. Future aspects such as roadbed charging are presented. Various power level chargers and infrastructure configurations are presented, compared, and evaluated based on amount of power, charging time and location, cost, equipment, and other factors.

Current control techniques for three-phase voltage-source PWM converters: a survey

Abstract: The aim of this paper is to present a review of current control techniques for three-phase voltage-source pulsewidth modulated converters. Various techniques, different in concept, have been described in two main groups: linear and nonlinear. The first includes proportional integral (stationary and synchronous) and state feedback controllers, and predictive techniques with constant switching frequency. The second comprises bang-bang (hysteresis, delta modulation) controllers and predictive controllers with on-line optimization. New trends in current control-neural networks and fuzzy-logic-based controllers-are discussed, as well. Selected oscillograms accompany the presentation in order to illustrate properties of the described controller groups.