Srinivasa R. Bakshi

Bio: Srinivasa R. Bakshi is an academic researcher from Indian Institute of Technology Madras. The author has contributed to research in topics: Spark plasma sintering & Carbon nanotube. The author has an hindex of 34, co-authored 99 publications receiving 4515 citations. Previous affiliations of Srinivasa R. Bakshi include Naval Postgraduate School & Indian Institutes of Technology.

Aluminum composite reinforced with multiwalled carbon nanotubes from plasma spraying of spray dried powders

Abstract: Homogenous dispersion of carbon nanotubes (CNTs) in micron sized aluminum silicon alloy powders was achieved by spray drying. Excellent flowability of the powders allowed fabrication of thick composite coatings and hollow cylinders (5 mm thick) containing 5 wt.% and 10 wt.% CNT by plasma spraying. Two phase microstructure with matrix having good distribution of CNT and CNT rich clusters was observed. Microstructural evolution has been explained using single splat and the infiltration of CNT clusters by liquid metal. Partial CNT surface damage was observed in case of the 10 wt.% CNT coating due to CNT mesh formation and smaller size of spray dried agglomerate. Increase in the elastic modulus and improvement in the yield strength and elastic recovery properties due to CNT addition was observed by nanoindentation.

Aluminum-Based Cast In Situ Composites: A Review

Abstract: In situ composites are a class of composite materials in which the reinforcement is formed within the matrix by reaction during the processing. In situ method of composite synthesis has been widely followed by researchers because of several advantages over conventional stir casting such as fine particle size, clean interface, and good wettability of the reinforcement with the matrix and homogeneous distribution of the reinforcement compared to other processes. Besides this, in situ processing of composites by casting route is also economical and amenable for large scale production as compared to other methods such as powder metallurgy and spray forming. Commonly used reinforcements for Al and its alloys which can be produced in situ are Al2O3, AlN, TiB2, TiC, ZrB2, and Mg2Si. The aim of this paper is to review the current research and development in aluminum-based in situ composites by casting route.

Synthesis and characterization of multiwalled carbon nanotube reinforced ultra high molecular weight polyethylene composite by electrostatic spraying technique

Abstract: In the present work, multiwalled carbon nanotube (MWNT) reinforced UHMWPE composite films were prepared by electrostatic spraying followed by consolidation. X-ray diffraction and differential scanning calorimetry studies showed a decrease in the crystallinity of UHMWPE due to the nature of the fabrication process as well as addition of MWNT. Tensile test showed an 82% increase in the Young’s modulus, decrease in stress to failure from 14.3 to 12.4 MPa and strain to failure from 3.9% to 1.4% due to 5% addition of MWNT. Raman spectra showed the presence of compressive stresses in the nanotubes. Fracture surface showed presence of pullout like phenomena in the MWNT reinforced film. � 2007 Elsevier Ltd. All rights reserved.

Effect of different carbon nano-fillers on rheological properties and lap shear strength of epoxy adhesive joints

Abstract: In this work, the rheological properties, thermal stability and the lap shear strength of epoxy adhesive joints reinforced with different carbon nano-fillers such as multi-walled carbon nanotubes (CNT), graphene nanoplatelets (GNP) and single-walled carbon nanohorns (CNH) have been studied. The nano-fillers were dispersed homogeneously using Brabender® Plasti-Corder®. The epoxy pre-polymer with and without the nano-fillers exhibited shear thinning behavior. The nano-filler epoxy mixtures exhibited a viscoplastic behavior which was analyzed using Casson’s model. Thermo-gravimetric analysis indicated an increase in the thermal stability of the epoxy with the addition of carbon nano-fillers. Carbon nano-fillers resulted in increased lap shear strength having high Weibull modulus. The joint strength increased by 53%, 49% and 46% with the addition of 1 wt.% CNT, 0.5 wt.% GNP and 0.5 wt.% CNH, respectively. The strength of the joints having high filler content (>1 wt.%) was limited by mixed mode type of failure.

Fast parallel algorithms for short-range molecular dynamics

Abstract: Three parallel algorithms for classical molecular dynamics are presented. The first assigns each processor a fixed subset of atoms; the second assigns each a fixed subset of inter-atomic forces to compute; the third assigns each a fixed spatial region. The algorithms are suitable for molecular dynamics models which can be difficult to parallelize efficiently—those with short-range forces where the neighbors of each atom change rapidly. They can be implemented on any distributed-memory parallel machine which allows for message-passing of data between independently executing processors. The algorithms are tested on a standard Lennard-Jones benchmark problem for system sizes ranging from 500 to 100,000,000 atoms on several parallel supercomputers--the nCUBE 2, Intel iPSC/860 and Paragon, and Cray T3D. Comparing the results to the fastest reported vectorized Cray Y-MP and C90 algorithm shows that the current generation of parallel machines is competitive with conventional vector supercomputers even for small problems. For large problems, the spatial algorithm achieves parallel efficiencies of 90% and a 1840-node Intel Paragon performs up to 165 faster than a single Cray C9O processor. Trade-offs between the three algorithms and guidelines for adapting them to more complex molecular dynamics simulations are also discussed.

Phd by thesis

Abstract: Deposits of clastic carbonate-dominated (calciclastic) sedimentary slope systems in the rock record have been identified mostly as linearly-consistent carbonate apron deposits, even though most ancient clastic carbonate slope deposits fit the submarine fan systems better. Calciclastic submarine fans are consequently rarely described and are poorly understood. Subsequently, very little is known especially in mud-dominated calciclastic submarine fan systems. Presented in this study are a sedimentological core and petrographic characterisation of samples from eleven boreholes from the Lower Carboniferous of Bowland Basin (Northwest England) that reveals a >250 m thick calciturbidite complex deposited in a calciclastic submarine fan setting. Seven facies are recognised from core and thin section characterisation and are grouped into three carbonate turbidite sequences. They include: 1) Calciturbidites, comprising mostly of highto low-density, wavy-laminated bioclast-rich facies; 2) low-density densite mudstones which are characterised by planar laminated and unlaminated muddominated facies; and 3) Calcidebrites which are muddy or hyper-concentrated debrisflow deposits occurring as poorly-sorted, chaotic, mud-supported floatstones. These

Carbon Nanotubes: Present and Future Commercial Applications

Abstract: Worldwide commercial interest in carbon nanotubes (CNTs) is reflected in a production capacity that presently exceeds several thousand tons per year. Currently, bulk CNT powders are incorporated in diverse commercial products ranging from rechargeable batteries, automotive parts, and sporting goods to boat hulls and water filters. Advances in CNT synthesis, purification, and chemical modification are enabling integration of CNTs in thin-film electronics and large-area coatings. Although not yet providing compelling mechanical strength or electrical or thermal conductivities for many applications, CNT yarns and sheets already have promising performance for applications including supercapacitors, actuators, and lightweight electromagnetic shields.