T. Ogura

Bio: T. Ogura is an academic researcher from Toshiba. The author has contributed to research in topics: Breakdown voltage & Power semiconductor device. The author has an hindex of 18, co-authored 33 publications receiving 1216 citations.

High breakdown voltage AlGaN-GaN power-HEMT design and high current density switching behavior

Abstract: AlGaN-GaN power high-electron mobility transistors (HEMTs) with 600-V breakdown voltage are fabricated and demonstrated as switching power devices for motor drive and power supply applications. The fabricated power HEMT realized the high breakdown voltage by optimized field plate technique and the low on-state resistance of 3.3 m/spl Omega/cm/sup 2/, which is 20 times lower than that or silicon MOSFETs, thanks to the high critical field of GaN material and the high mobility in 2DEG channel. The fabricated devices also demonstrated the high current density switching of 850 A/cm/sup 2/ turn-off. These results show that AlGaN-GaN power-HEMTs are one of the most promising candidates for future switching power device for power electronics applications.

Influence of surface defect charge at AlGaN-GaN-HEMT upon Schottky gate leakage current and breakdown voltage

Abstract: The relation between Schottky gate leakage current and the breakdown voltage of AlGaN-GaN high-electron mobility transistors (HEMTs) is discussed based on the newly introduced simple, yet useful, surface defect charge model. This model represents the leakage current caused by the positive charge in the surface portion of AlGaN layer induced by process damage such as nitrogen vacancies. The new model has been implemented into a two-dimensional device simulator, and the relationship between the gate leakage current and the breakdown voltage was simulated. The simulation results reproduced the relationship obtained experimentally between the leakage current and the breakdown voltage. Further simulation and experiment results show that the breakdown voltage is maintained even if the defect charge exists up to the defect charge density of 2.5/spl times/10/sup 12/ cm/sup -2/, provided the field plate structure is adopted, while the breakdown voltage shows a sudden drop for the defect density over 5/spl times/10/sup 11/ cm/sup -2/ without the field plate. This result shows that the field plate structure is effective for suppressing the surface charge influence on breakdown voltage due to the relaxation of the electric field concentration in the surface portion of the AlGaN layer.

Design optimization of high breakdown voltage AlGaN-GaN power HEMT on an insulating substrate for R/sub ON/A-V/sub B/ tradeoff characteristics

Abstract: High breakdown voltage AlGaN-GaN power high-electron mobility transistors (HEMTs) on an insulating substrate were designed for the power electronics application. The field plate structure was employed for high breakdown voltage. The field plate length, the insulator thickness and AlGaN layer doping concentration were design parameters for the breakdown voltage. The optimization of the contact length and contact resistivity reduction were effective to reduce the specific on-resistance. The tradeoff characteristics between the on-resistance and the breakdown voltage can be improved by the optimization of the above design parameters, and the on-resistance can be estimated to be about 0.6 m/spl Omega//spl middot/cm/sup 2/ for the breakdown voltage of 600 V. This on-resistance is almost the same as that for the device on a conductive substrate.

High breakdown Voltage undoped AlGaN-GaN power HEMT on sapphire substrate and its demonstration for DC-DC converter application

Abstract: Undoped AlGaN-GaN power high electron mobility transistors (HEMTs) on sapphire substrate with 470-V breakdown voltage were fabricated and demonstrated as a main switching device for a high-voltage dc-dc converter. The fabricated power HEMT realized a high breakdown voltage with a field plate structure and a low on-state resistance of 3.9 m/spl Omega//spl middot/cm/sup 2/, which is 10 /spl times/ lower than that of conventional Si MOSFETs. The dc-dc converter operation of a down chopper circuit was demonstrated using the fabricated device at the input voltage of 300 V. These results show the promising possibilities of the AlGaN-GaN power HEMTs on sapphire substrate for future switching power devices.

600V AlGaN/GaN power-HEMT: design, fabrication and demonstration on high voltage DC-DC converter

Abstract: A 600 V class AlGaN/GaN power HEMT was designed for high voltage power electronics application such as power supplies and motor drives The fabricated device was demonstrated in a DC-DC down converter circuit, showing the future possibility of high efficiency and high frequency operations of AlGaN/GaN power HEMTs

Gate Injection Transistor (GIT)—A Normally-Off AlGaN/GaN Power Transistor Using Conductivity Modulation

Abstract: We have developed a normally-off GaN-based transistor using conductivity modulation, which we call a gate injection transistor (GIT). This new device principle utilizes hole-injection from the p-AlGaN to the AlGaN/GaN heterojunction, which simultaneously increases the electron density in the channel, resulting in a dramatic increase of the drain current owing to the conductivity modulation. The fabricated GIT exhibits a threshold voltage of 1.0 V with a maximum drain current of 200 mA/mm, in which a forward gate voltage of up to 6 V can be applied. The obtained specific ON-state resistance (RON . A) and the OFF-state breakdown voltage (BV ds) are 2.6 mOmega . cm2 and 800 V, respectively. The developed GIT is advantageous for power switching applications.

Condition Monitoring for Device Reliability in Power Electronic Converters: A Review

Abstract: Condition monitoring (CM) has already been proven to be a cost effective means of enhancing reliability and improving customer service in power equipment, such as transformers and rotating electrical machinery. CM for power semiconductor devices in power electronic converters is at a more embryonic stage; however, as progress is made in understanding semiconductor device failure modes, appropriate sensor technologies, and signal processing techniques, this situation will rapidly improve. This technical review is carried out with the aim of describing the current state of the art in CM research for power electronics. Reliability models for power electronics, including dominant failure mechanisms of devices are described first. This is followed by a description of recently proposed CM techniques. The benefits and limitations of these techniques are then discussed. It is intended that this review will provide the basis for future developments in power electronics CM.

High-performance enhancement-mode AlGaN/GaN HEMTs using fluoride-based plasma treatment

Abstract: We report a novel approach in fabricating high-performance enhancement mode (E-mode) AlGaN/GaN HEMTs. The fabrication technique is based on fluoride-based plasma treatment of the gate region in AlGaN/GaN HEMTs and post-gate rapid thermal annealing with an annealing temperature lower than 500/spl deg/C. Starting with a conventional depletion-mode HEMT sample, we found that fluoride-based plasma treatment can effectively shift the threshold voltage from -4.0 to 0.9 V. Most importantly, a zero transconductance (g/sub m/) was obtained at V/sub gs/=0 V, demonstrating for the first time true E-mode operation in an AlGaN/GaN HEMT. At V/sub gs/=0 V, the off-state drain leakage current is 28 /spl mu/A/mm at a drain-source bias of 6 V. The fabricated E-mode AlGaN/GaN HEMTs with 1 /spl mu/m-long gate exhibit a maximum drain current density of 310 mA/mm, a peak g/sub m/ of 148 mS/mm, a current gain cutoff frequency f/sub T/ of 10.1 GHz and a maximum oscillation frequency f/sub max/ of 34.3 GHz.

Power semiconductor device

Abstract: A power semiconductor device includes trenches disposed in a first base layer of a first conductivity type at intervals to partition main and dummy cells, at a position remote from a collector layer of a second conductivity type. In the main cell, a second base layer of the second conductivity type, and an emitter layer of the first conductivity type are disposed. In the dummy cell, a buffer layer of the second conductivity type is disposed. A gate electrode is disposed, through a gate insulating film, in a trench adjacent to the main cell. A buffer resistor having an infinitely large resistance value is inserted between the buffer layer and emitter electrode. The dummy cell is provided with an inhibiting structure to reduce carriers of the second conductivity type to flow to and accumulate in the buffer layer from the collector layer.

Recessed-gate structure approach toward normally off high-Voltage AlGaN/GaN HEMT for power electronics applications

Abstract: A recessed-gate structure has been studied with a view to realizing normally off operation of high-voltage AlGaN/GaN high-electron mobility transistors (HEMTs) for power electronics applications. The recessed-gate structure is very attractive for realizing normally off high-voltage AlGaN/GaN HEMTs because the gate threshold voltage can be controlled by the etching depth of the recess without significant increase in on-resistance characteristics. With this structure the threshold voltage can be increased with the reduction of two-dimensional electron gas (2DEG) density only under the gate electrode without reduction of 2DEG density in the other channel regions such as the channel between drain and gate. The threshold-voltage increase was experimentally demonstrated. The threshold voltage of fabricated recessed-gate device increased to -0.14 V while the threshold voltage without the recessed-gate structure was about -4 V. The specific on-resistance of the device was maintained as low as 4 m/spl Omega//spl middot/cm/sup 2/ and the breakdown voltage was 435 V. The on-resistance and the breakdown voltage tradeoff characteristics were the same as those of normally on devices. From the viewpoint of device design, the on-resistance for the normally off device was modeled using the relationship between the AlGaN layer thickness under the gate electrode and the 2DEG density. It is found that the MIS gate structure and the recess etching without the offset region between recess edge and gate electrode will further improve the on-resistance. The simulation results show the possibility of the on-resistance below 1 m/spl Omega//spl middot/cm/sup 2/ for normally off AlGaN/GaN HEMTs operating at several hundred volts with threshold voltage up to +1 V.