Taiping Lu

Bio: Taiping Lu is an academic researcher from Southwest Jiaotong University. The author has contributed to research in topics: Elastic modulus & Water cooling. The author has an hindex of 1, co-authored 1 publications receiving 2 citations.

An Experimental Study on the Mechanical Properties of High-Temperature Granite under Natural Cooling and Water Cooling

Abstract: With the further development of deep rock mechanics engineering, such as the exploitation and utilization of geothermal resources, the exploitation of deep mineral resources, and the safe disposal of nuclear waste, the study of mechanical properties of deep high-temperature rock is gaining the attention of the researchers. However, not only the high temperature but also the cooling condition/method that will be used in the construction such as drilling cooling will also greatly affect the mechanical properties of the rock. In this paper, the mechanical behaviour and the evolution of the mechanical properties of the high-temperature (600°C–1,000°C) granite under different cooling methods are studied. The following conclusions can be obtained: (1) The peak stress of the granite decreases with the heating temperature. Compared with natural cooling, water cooling has a more significant effect on strength degradation. (2) The increase of the heating temperature increases the maximum axial strain of the granite. The water cooling method more greatly induces the maximum axial strain of granite than the natural cooling. The maximum axial strain of the specimen under the water cooling reaches 117.3% of that under natural cooling (800°C). (3) The elastic modulus of the granite decreases with the heating temperature. Water cooling will have a stronger effect on the reduction of the elastic modulus than natural cooling. The maximum difference value (2.02 GPa) of the elastic modulus under the different cooling methods occurs at the temperature of 800°C. (4) Poisson’s ratio of the granite increases with heating temperature, and the cooling method does not have an evident effect on it. The relationship between Poisson’s ratio and the heating temperature under different cooling methods can be described using the linear model. (5) According to the influence of the temperature on the peak stress, the elastic modulus, and Poisson’s ratio, the heating temperature domain can be divided into the unapparent zone, the significant zone, and the mitigation zone. (6) The thermal stress due to the nonuniform temperature field and the different thermal expansion coefficients is incompatible. Such incompatibility stresses the essences of the degradation of the mechanical properties of the granite.

Coupled thermal-hydrological-mechanical analyses of the Yucca Mountain Drift Scale Test - Comparison of field measurements to predictions of four different numerical models

Abstract: The Yucca Mountain Drift Scale Test (DST) is a multiyear, large-scale underground heater test designed to study coupled thermal-hydrological-mechanical-chemical behavior in unsaturated fractured and welded tuff. As part of the international cooperative code-comparison project DECOVALEX, four research teams used four different numerical models to simulate and predict coupled thermal-hydrological-mechanical (THM) processes at the DST. The simulated processes included above-boiling temperature changes, liquid and vapor water movements, rock-mass stress and displacement, and THM-induced changes in fracture permeability. Model predictions were evaluated by comparison to measurements of temperature, water saturation, displacement, and air permeability. The generally good agreement between simulated and measured THM data shows that adopted continuum model approaches are adequate for simulating relevant coupled THM processes at the DST. Moreover, TM-induced rock-mass deformations were reasonably well predicted using elastic models, although some individual displacements appeared to be better captured using an elasto-plastic model. It is concluded that fracture closure/opening caused by change in normal stress across fractures is the dominant mechanism for TM-induced changes in intrinsic fracture permeability at the DST, whereas fracture shear dilation appears to be less significant. This indicates that TM-induced changes in intrinsic permeability at the DST, which are within one order of magnitude, tend to be reversible.

DDA Simulation Study on Mechanical Failure of Heterogenous Rock

Abstract: Heterogeneity is an important characteristic that affects the mechanical behavior of rock. In the present work, a statistical rock mesoheterogeneity model based on the Weibull distribution function is introduced into the discontinuous deformation analysis (DDA) method to simulate the mechanical failure of heterogeneous rock, in which the general heterogeneity degree is controlled by a heterogeneity index and the mechanical property of each subblock element is randomly assigned. Brazilian disc and uniaxial compressive rectangular specimens are simulated as examples. Results show that it is more reasonable to consider the heterogeneity of elasticity properties (the elastic modulus and Poisson’s ratio) and strength properties (the tensile strength, cohesion, and friction angle) simultaneously in the heterogeneity model. It is also shown that with a larger heterogeneity index, which means a lower degree of heterogeneity, the reproducibility of the macroscopic response curves of a specimen gets better, while the exact cracking always differs but with less scattered cracks, and the global fracturing failure pattern and mode are weakly influenced by the heterogeneity. Moreover, with the increase in the heterogeneity index, the macroscopic equivalent modulus and strength get larger and approach those of a homogeneous specimen. This work indicates the importance of heterogeneity for rock mechanical behaviors including the macroscopic equivalent response and the fracturing failure. By the subblock DDA method to simulate fracturing realistically, the fracturing failure process of heterogeneous rock can be successfully reproduced, which builds good foundation for the simulation study of heterogeneous rock fracturing in practical problems, e.g., coal and rock fracturing in fluidization mining in the future.