Valerio Lo Brano

Bio: Valerio Lo Brano is an academic researcher from University of Palermo. The author has contributed to research in topics: Photovoltaic system & Renewable energy. The author has an hindex of 23, co-authored 54 publications receiving 2161 citations.

Energy performances and life cycle assessment of an Italian wind farm

Abstract: Renewable energy sources are often presented as “ clean ”. A more correct definition is that they are “cleaner” than ones based on fossil fuel conversion. When the energy consumption and the environmental impacts related to the plant's life-cycle are considered, a more comprehensive assessment of these technologies can be carried out. This paper aims to evaluate the energy and the environmental performances of the electricity production of a wind farm. The impacts related to all the phases of the wind farm construction and operation have been compared to the environmental benefits due to the “green” electricity generation during its useful life. In other terms, the goal is to trace the ecoprofile of the production of 1 kWh of electricity. A life cycle assessment (LCA) has been performed based on data related to an Italian wind farm: production and deliver of energy and raw materials, components manufacturing, transports, installation, maintenance, disassembly and disposal have been analysed. The attention focused to those life cycle steps generally neglected or not adequately investigated as installation, civil works and maintenance. The results can be assumed as representative of the Italian context and they can represent a further incentive to the diffusion of wind farms. In fact, the environmental performances of the wind farm have been compared to other power energy generation systems. The results showed a great environmental convenience of the inquired technology.

A comparison of different one-diode models for the representation of I–V characteristic of a PV cell

Abstract: Predictive performance tools are an important factor in the success of any new technology because they permit demonstration of whether a system will be efficient and economically feasible. A reliable predictive tool should allow the designer to optimise system performance and to maximise the cost effectiveness of a system prior to installation. This article discusses the five main parametric models for photovoltaic (PV) systems available in the literature. The current–voltage characteristics of a photovoltaic module can be reproduced modelling the PV panel as an equivalent electrical circuit made of linear and non-linear components. The parameters describing such components are directly related to the performance characteristics of the specific PV panel, which are generally available in a graphic form with respect to standard values of temperature and incident irradiance. Five of the most recent models are analysed in detail describing the algorithm, showing how the parameters were determined and highlighting the most important mathematical and physical assumptions that characterised each model and the calculation process. To simplify the examination and reading of the procedures referred to in the five models, all equations are rewritten using the same nomenclature. Furthermore, to assess the accuracy of each model with respect to the data provided by the manufacturer, this paper compares the I–V and P–V curves at various temperatures and irradiance for a generic PV panel.

Pattern Recognition and Machine Learning

Abstract: Probability Distributions.- Linear Models for Regression.- Linear Models for Classification.- Neural Networks.- Kernel Methods.- Sparse Kernel Machines.- Graphical Models.- Mixture Models and EM.- Approximate Inference.- Sampling Methods.- Continuous Latent Variables.- Sequential Data.- Combining Models.

World energy outlook

Abstract: This chapter discusses leading problems linked to energy that the world is now confronting and to propose some ideas concerning possible solutions. Oil deserves special attention among all energy sources. Since the beginning of 1981, it has merely been continuing and enhancing the downward movement in consumption and prices caused by excessive rises, especially for light crudes such as those from Africa, and the slowing down of worldwide economic growth. Densely-populated oil-producing countries need to produce to live, to pay for their food and their equipment. If the economic growth of the industrialized countries were to be 4%, even if investment in the rational use of energy were pushed to the limit and the development of nonpetroleum energy sources were also pursued actively, it would be extremely difficult to prevent a sharp rise in prices. It is evident that it is absolutely necessary to pursue actively the development of coal, natural gas, and nuclear power if a physical shortage of energy is not to block economic growth.

Climate Change 1995

Abstract: Climate Change 1995 is a scientific assessment that was generated by more than 1 000 contributors from over 50 nations. It was jointly co-ordinated through two international agencies; the World Meteorological Organization and the United Nations Environment Programme. The assessment was completed by the Intergovernmental Panel on Climate Change (IPCC) with a primary aim of reviewing the current state of knowledge concerning the impacts of climate change on physical and ecological systems, human health, and socioeconomic factors. The second aim was to review the available information on the technical and economic feasibility of the potential mitigation and adaptation strategies.

A review of biodiesel production from Jatropha curcas L. oil

Abstract: The demand for petroleum has risen rapidly due to increasing industrialization and modernization of the world. This economic development has led to a huge demand for energy, where the major part of that energy is derived from fossil sources such as petroleum, coal and natural gas. However, the limited reserve of fossil fuel has drawn the attention of many researchers to look for alternative fuels which can be produced from renewable feedstock. Biodiesel has become more attractive because of its environmental benefits and it is obtained from renewable resources. There are four primary methods to make biodiesel: blending, microemulsion, pyrolysis and transesterification. The most commonly used method is the transesterification of triglycerides (vegetable oil and animal fats) with alcohol in the presence of a catalyst. There is a growing interest in using Jatropha curcas L. oil as the feedstock for biodiesel production because it is non-edible and thus does not compromise the edible oils, which are mainly used for food consumption. Non-edible oils are not suitable for human consumption because of the presence of toxic components. Further, J. curcas L. seed has a high content of oil and the biodiesel produced has similar properties to that of petroleum-based diesel. In this paper, an attempt has been made to review the different approaches and techniques used to generate biodiesel from Jatropha curcas oil. The main factors affecting the biodiesel yield, for example the molar ratio of alcohol to oil, catalyst concentration, reaction temperature and reaction time are discussed. Lastly, the environmental considerations and economic aspects of biodiesel are also addressed.