Vicente Castelo Branco Leitune

Bio: Vicente Castelo Branco Leitune is an academic researcher from Universidade Federal do Rio Grande do Sul. The author has contributed to research in topics: Adhesive & Bond strength. The author has an hindex of 21, co-authored 113 publications receiving 1328 citations.

Discrepancies in degree of conversion measurements by FTIR

Abstract: The purpose of this study was to evaluate the influence of the internal standard peak on the measured degree of conversion (DC) for methacrylate-based resins analyzed by Fourier-transform infrared spectroscopy (FTIR). The influence of different baseline measurement methods was also determined. Different blends were prepared, mixing BisGMA/BisEMA and BisGMA/TEGDMA at proportions of 0% to 100%, in weight. Camphoroquinone and ethyl-4-dimethylamino-benzoate were used to permit the light activation of blends. Degree of conversion was evaluated using FTIR equipped with an attenuated total reflectance (ATR) device. Samples were dispensed onto ATR crystal and light activated for 40 s. The DC was calculated by relating the height of the peak 1637 cm-1 to the intensity of different internal standard peaks (1715, 1608, or 1582 cm-1), measured using two different baseline methods, before and after polymerization. Data were compared by ANOVA at 5% significance. The relationship between DC and monomer ratio was obtained by regression analysis. Double-bond conversion ranged from 32.75% to 78.50% for BisGMA/BisEMA blends, and from 32.75% to 76.22% for BisGMA/TEGDMA blends. For the BisGMA/BisEMA blends, the DC showed a linear association with the composition of the comonomer blends, independent of the internal standard peak and baseline method used. In contrast, the trends in DC for BisGMA/TEGDMA blends were different for each method of measurement. The internal standard peaks and measurement baseline should be taken into account when using FTIR to calculate the DC of methacrylate-based resins, especially comonomer blends containing a high degree of monomers that lack aromatic rings.

Effect of silver nanoparticles on the physicochemical and antimicrobial properties of an orthodontic adhesive

Abstract: Orthodontic treatment with fixed brackets plays a major role on the formation of white spot lesions. Objective This study aimed to incorporate silver nanoparticle solutions (AgNP) in an orthodontic adhesive and evaluate its physicochemical and antimicrobial properties. Material and Methods Silver nanoparticle solutions were added to a commercial adhesive in different concentrations (w/w): 0%, 0.11%, 0.18%, and 0.33%. Shear bond strength (SBS) test was performed after bonding metal brackets to enamel. Raman spectroscopy was used to analyze in situ the degree of conversion (DC) of the adhesive layer. The surface free energy (SFE) was evaluated after the measurement of contact angles. Growth inhibition of Streptococcus mutans in liquid and solid media was determined by colony-forming unit count and inhibition halo, respectively. One-way ANOVA was performed for SBS, DC, SFE, and growth inhibition. Results The incorporation of AgNP solution decreased the SBS (p<0.001) and DC in situ (p<0.001) values. SFE decreased after addition of 0.18% and 0.33% AgNP. Growth inhibition of S. mutans in liquid media was obtained after silver addition (p<0.05). Conclusions The addition of AgNP solutions to Transbond™ XT adhesive primer inhibited S. mutans growth. SBS, DC, and SFE values decreased after incorporation up to 0.33% AgNP solution without compromising the chemical and physical properties of the adhesive.

The influence of methodological variables on the push-out resistance to dislodgement of root filling materials: a meta-regression analysis.

Abstract: The aim of this systematic review was to evaluate the influence of several methodological variables on the push-out resistance to dislodgment of root filling materials by a meta-regression analysis of the literature. A systematic review was performed by searching the PubMed database using the terms 'push-out' and 'pushout'. Laboratory studies published before March 2015 were included. Two reviewers extracted data regarding country of origin, year of publication, tooth type, smear layer removal, root canal sealer, core material, obturation technique, sample storage, tooth portion, test machine load velocity and slice thickness. Pooled mean resistance to dislodgement of all groups from the included studies was used in a linear meta-regression of random effects (α = 0.05). Of the 850 identified studies, 53 met the inclusion criteria. A meta-regression of the 341 groups extracted from these articles was performed to analyse the influence of each variable on resistance to dislodgement (in MPa). The sealer, core material, obturation technique, slice thickness, storage time, load velocity and tooth portion significantly influence the results (P 0.05). Methodological variables such as sealer, core material, root filling technique, tooth type, tooth portion, slice thickness, storage time and load velocity influenced the resistance to dislodgment. The inclusion and standardization of all related variables could lead to a more comparable and reproducible analysis of the resistance to dislodgment of the root canal sealers.