Warren Batchelor

Bio: Warren Batchelor is an academic researcher from Monash University, Clayton campus. The author has contributed to research in topics: Nanocellulose & Cellulose. The author has an hindex of 23, co-authored 152 publications receiving 1928 citations. Previous affiliations of Warren Batchelor include University of British Columbia & Monash University.

Estimation of cellulose nanofibre aspect ratio from measurements of fibre suspension gel point

Abstract: Cellulose nanofibre aspect ratio controls the properties of sheets made from nanofibres and processing conditions, but aspect ratio is very difficult to measure. In this paper, aspect ratio was estimated from the gel point of a cellulose nanofibre suspension, the solids concentration at which the transition from a dilute to a semi-dilute suspension occurs. Four batches of cellulose nanofibres were tested. Two were produced from softwood fibres using ball milling. Commercially produced microfibrillated cellulose material was also used, both in as supplied form and after removal of the larger fibres by filtering. The average diameter measured from SEM images of fibres ranged from 33 to 73 nm. One sample was too heavily treated and an average dimension could not be measured. The gel-point was measured both from the height of a layer of cellulose nanofibres sedimented from a dilute suspension or from the lowest solids concentration at which a yield stress could be measured using a vane rheometer. The two methods were closely in agreement for all samples. Aspect ratio was then calculated using either the effective medium (EMT) or crowding number (CN) theories. Aspect ratio calculated with an assumed fibre density of 1,500 kg/m3, using the CN theory ranged from 155 to 60. Use of the EMT theory reduced the calculated aspect ratio by between 11 and 23 %. Reducing the assumed density in suspension from 1,500 to 1,166 kg/m3 reduced the calculated aspect ratio by 12–14 %. The heavily treated sample had by far the lowest aspect ratio.

Effect of cellulose nanofiber dimensions on sheet forming through filtration

Abstract: Four different cellulose nanofibers samples were prepared from northern bleached softwood kraft fibers. Fiber diameter distributions were measured from SEM images. Fiber aspect ratios ranging from 84 to 146 were estimated from fiber suspension sedimentation measurements. Three samples had heterogeneous distributions of fiber diameters, while one sample was more homogeneous. Sheet forming experiments using filters with pores ranging from 150 to 5 μm showed that the samples with a heterogeneous distribution of fiber dimensions could be easily formed into sheets at 0.2% initial solids concentration with all filter openings. On the other hand, sheets could only be formed from the homogenous sample by using 0.5% or more initial solids content and a lower applied vacuum and smaller filter openings. The forming data and estimated aspect ratios show reasonable agreement with the predictions of the crowding number and percolation theories for the connectivity and rigidity thresholds for fiber suspensions.

Pickering Emulsions Electrostatically Stabilized by Cellulose Nanocrystals

Abstract: Cellulose Nanocrystals (CNC) are explored to stabilize oil/water emulsions for their ability to adsorb at the oil/water interface In this work, the role of electrostatic forces in the CNC ability to stabilize oil/water emulsions is explored using canola oil/water and hexadecane/water as model systems Canola oil/water and Hexadecane/ water (20/80, v/v) emulsions were stabilized with the addition of CNCs using ultrasonication Emulsion droplet sizes range from 1 to 4 μm as measured by optical microscopy It is found that CNC can stabilize oil/water emulsions regardless of their charge density However, reducing the surface charge density, by adding salts and varying pH, can reduce the amount of CNC's required to form a stable emulsion Just by adding 3 mM Na+ or 1 mM or less Ca+2 to a CNC suspension, the amount of CNC reduced by 30% to stabilized 2 mL of Canola oil On the other hand, adding salt increases the emulsion volume The addition of 100 mM Na+ or the reduction of pH below 2 leads to the aggregation of CNC; emulsions formed under these conditions showed gel-like behavior This work shows the potential of nanocellulose crystal in stabilizing food and industrial emulsions This is of interest for applications where biodegradability, biocompatibility, and food grade requirements are needed

Effect of Temperature

Abstract: A positive temperature coefficient is the term which has been used to indicate that an increase in solubility occurs as the temperature is raised, whereas a negative coefficient indicates a decrease in solubility with rise in temperature.

Determining Beta Sheet Crystallinity in Fibrous Proteins by Thermal Analysis and Infrared Spectroscopy

Abstract: We report a study of self-assembled beta-pleated sheets in B. mori silk fibroin films using thermal analysis and infrared spectroscopy. B. mori silk fibroin may stand as an exemplar of fibrous proteins containing crystalline beta-sheets. Materials were prepared from concentrated solutions (2−5 wt % fibroin in water) and then dried to achieve a less ordered state without beta-sheets. Crystallization of beta-pleated sheets was effected either by heating the films above the glass transition temperature (Tg) and holding isothermally or by exposure to methanol. The fractions of secondary structural components including random coils, alpha-helices, beta-pleated sheets, turns, and side chains were evaluated using Fourier self-deconvolution (FSD) of the infrared absorbance spectra. The silk fibroin films were studied thermally using temperature-modulated differential scanning calorimetry (TMDSC) to obtain the reversing heat capacity. The increment of the reversing heat capacity ΔCp0(Tg) at the glass transition fo...

The dry-style antifogging properties of mosquito compound eyes and artificial analogues prepared by soft lithography: a superhydrophobic state with high adhesive force

Abstract: Fogging occurs when moisture condensation takes the form of accumulated droplets with diameters larger than 190 nm or half of the shortest wavelength (380 nm) of visible light. This problem may be effectively addressed by changing the affinity of a material’s surface for water, which can be accomplished via two approaches: i) the superhydrophilic approach, with a water contact angle (CA) less than 5°, and ii) the superhydrophobic approach, with a water CA greater than 150°, and extremely low CA hysteresis. To date, all techniques reported belong to the former category, as they are intended for applications in optical transparent coatings. A well-known example is the use of photocatalytic TiO2 nanoparticle coatings that become superhydrophilic under UV irradiation. Very recently, a capillary effect was skillfully adopted to achieve superhydrophilic properties by constructing 3D nanoporous structures from layer-by-layer assembled nanoparticles. The key to these two “wet”-style antifogging strategies is for micrometer-sized fog drops to rapidly spread into a uniform thin film, which can prevent light scattering and reflection from nucleated droplets. Optical transparency is not an intrinsic property of antifogging coatings even though recently developed antifogging coatings are almost transparent, and the transparency could be achieved by further tuning the nanoparticle size and film thickness. To our knowledge, the antifogging coatings may also be applied to many fields that do not require optical transparency, including, for example, paints for inhibiting swelling and peeling issues and metal surfaces for preventing corrosion. These types of issues, which are caused by adsorption of moisture, are hard to solve by the superhydrophilic approach because of its inherently “wet” nature. Thus, a “dry”-style antifogging strategy, which consists of a novel superhydrophobic technique that can prevent moisture or microscale fog drops from nucleating on a surface, is desired. Recent bionic researches have revealed that the self-cleaning ability of lotus leaves and the striking ability of a water-strider’s legs to walk on water can be attributed to the ideal superhydrophobicity of their surfaces, induced by special microand nanostructures. To date, the biomimetic fabrication of superhydrophobic microand/or nanostructures has attracted considerable interest, and these types of materials can be used for such applications as self-cleaning coatings and stain-resistant textiles. Although a superhydrophobic technique inspired by lotus leaves is expected to be able to solve such fogging problems because the water droplets can not remain on the surface, there are no reports of such antifogging coatings. Very recently, researchers from General Motors have reported that the surfaces of lotus leaves become wet with moisture because the size of the fog drops are at the microscale—so small that they can be easily trapped in the interspaces among micropapillae. Thus, lotuslike surface microstructures are unsuitable for superhydrophobic antifogging coatings, and a new inspiration from nature is desired for solving this problem. In this communication, we report a novel, biological, superhydrophobic antifogging strategy. It was found that the compound eyes of the mosquito C. pipiens possess ideal superhydrophobic properties that provide an effective protective mechanism for maintaining clear vision in a humid habitat. Our research indicates that this unique property is attributed to the smart design of elaborate microand nanostructures: hexagonally non-close-packed (ncp) nipples at the nanoscale prevent microscale fog drops from condensing on the ommatidia surface, and hexagonally close-packed (hcp) ommatidia at the microscale could efficiently prevent fog drops from being trapped in the voids between the ommatidia. We also fabricated artificial compound eyes by using soft lithography and investigated the effects of microand nanostructures on the surface hydrophobicity. These findings could be used to develop novel superhydrophobic antifogging coatings in the near future. It is known that mosquitoes possess excellent vision, which they exploit to locate various resources such as mates, hosts, and resting sites in a watery and dim habitat. To better understand such remarkable abilities, we first investigated the interaction between moisture and the eye surface. An ultrasonic humidifier was used to regulate the relative humidity of the atmosphere and mimic a mist composed of numerous tiny water droplets with diameters less than 10 lm. As the fog was C O M M U N IC A IO N

The wood from the trees: The use of timber in construction

Abstract: Trees, and their derivative products, have been used by societies around the world for thousands of years. Contemporary construction of tall buildings from timber, in whole or in part, suggests a growing interest in the potential for building with wood at a scale not previously attainable. As wood is the only significant building material that is grown, we have a natural inclination that building in wood is good for the environment. But under what conditions is this really the case? The environmental benefits of using timber are not straightforward; although it is a natural product, a large amount of energy is used to dry and process it. Much of this can come from the biomass of the tree itself, but that requires investment in plant, which is not always possible in an industry that is widely distributed among many small producers. And what should we build with wood? Are skyscrapers in timber a good use of this natural resource, or are there other aspects of civil and structural engineering, or large-scale infrastructure, that would be a better use of wood? Here, we consider a holistic picture ranging in scale from the science of the cell wall to the engineering and global policies that could maximise forestry and timber construction as a boon to both people and the planet.