Winifred Obande

Bio: Winifred Obande is an academic researcher from University of Edinburgh. The author has contributed to research in topics: Flexural strength & Thermoplastic. The author has an hindex of 6, co-authored 13 publications receiving 250 citations. Previous affiliations of Winifred Obande include University of Limerick.

Mechanical characterisation of carbon fibre–PEEK manufactured by laser-assisted automated-tape-placement and autoclave

Abstract: Obtaining autoclave-level mechanical properties using in-situ consolidation of thermoplastic composites by Automated Tape Placement (ATP) is challenging. However, relatively recent availability of high quality ATP grade pre-preg material and tape heads equipped with more efficient heat sources (e.g. lasers) offers an opportunity to achieve improved mechanical properties and deposition rates. In the present study, carbon fibre–PEEK laminates, manufactured by laser-assisted ATP (LATP) and autoclave, are compared. Analysis of the through-thickness temperature distribution during LATP processing using thermocouples indicates that LATP cooling rates are extremely rapid and suggests full through-thickness melting of the pre-preg tape may not occur. Inadequate crystallinity, in conjunction with voids, compromised mechanical properties compared to autoclaved laminates but was beneficial in terms of the toughness of LATP laminates. Optimisation of pre-preg properties and processing parameters is required to realise the full potential of the LATP process in terms of mechanical properties, energy requirements, cost and deposition rates.

Fracture toughness of carbon fiber/polyether ether ketone composites manufactured by autoclave and laser-assisted automated tape placement

Abstract: A comparative study is presented on the fracture toughness of carbon fiber/PEEK composites manufactured by autoclave and laser-assisted automated tape placement (LATP). Formation of a good inter-laminar bond is always a concern in ATP due to the short time available for intimate contact development and polymer healing, yet our double cantilever beam (DCB) tests reveal 60- 80% higher Mode I fracture toughness for the LATP processed specimens than for the autoclave processed specimens. This magnitude of difference was unexpected, so specimens were further examined via differential scanning calorimetry, dynamic mechanical analysis, nano-indentation, and scanning electron microscopy. The results indicate that the LATP process has been very effective in heating and consolidating the surface of plies, creating an excellent bond. However, it has been less effective in processing the interior of plies, where a low crystallinity and poor fiber-matrix bonding are evident. The higher fracture toughness of the LATP processed specimens is also not solely due to a better bond, but is partially due to significant plastic deformation in the interior of plies during the DCB test. The findings indicate there is still considerable scope for optimizing the laser-assisted ATP process, before the optimum balance between strength and toughness is achieved at favorable lay-down speeds. V C 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41643.

Continuous fibre-reinforced thermoplastic acrylic-matrix composites prepared by liquid resin infusion – a review

Abstract: Increasing demand for lightweight materials is a major driving force for the steady growth of the continuous fibre-reinforced polymer composite industry. In recent years, strict global targets demanding greater environmental responsibility have led to a shift in research focus to address the end-of-life challenges posed by the use of thermoset matrices. Thermosets offer lower-cost processibility than thermoplastics, which historically required cost- and energy-intensive production methodologies. Consequently, despite their well-demonstrated recyclability, thermoformability and weldability, thermoplastics are yet to attain the same technological maturity as thermosets. In situ polymerisable thermoplastic resins have been identified as attractive emerging solutions for improving the processibility of thermoplastics. Thus, are essential materials in meeting the demand for fibre-reinforced thermoplastic composites. This review presents a comprehensive summary of recent works on room-temperature-processible liquid thermoplastic acrylic resins and their composites. Moreover, open problems and research opportunities are identified and discussed.

Voids in fiber-reinforced polymer composites: A review on their formation, characteristics, and effects on mechanical performance:

Abstract: Voids, the most studied type of manufacturing defects, form very often in processing of fiber-reinforced composites. Due to their considerable influence on physical and thermomechanical properties ...

Effect of processing parameters and void content on mechanical properties and NDI of thermoplastic composites

Abstract: Several consolidation cycles were performed to study the impact of processing parameters on void content, ultrasonic NDT and mechanical performance of CF/PEEK composites. A series of [+45/−45]4S laminates were manufactured by out-of-autoclave technologies including vacuum bag only, hot-press, and automatic lay-up with in-situ consolidation. A range of porosity between 0 and 19% of void content was assessed by varying the processing temperature from 340 to 500 °C and pressure from 0.25 to 1.5 MPa. Void content, shape and location were characterized by using C-scan, matrix digestion and 2D microscopy. Mechanical characterization including in-plane shear and interlaminar shear testing was performed. The results show a critical void content where properties start to decrease at a given drop-off rate. The results suggest that each processing technology should have its own quality control criteria. The proposed methodology is useful for engineering applications of thermoplastic composites and the creation of NDT acceptance criteria.

The effect of processing temperature and placement rate on the short beam strength of carbon fibre-PEEK manufactured using a laser tape placement process

Abstract: The ability of a modern near infra-red laser tape placement system to produce high-quality laminates is investigated by performing short beam strength tests on samples manufactured at different process temperatures from 400 °C to 600 °C at placement rates of 100 mm/s and 400 mm/s. The temperature history in tape placement is highly dynamic and the correlation between the process control temperature, laser power and the consolidation temperature is not well understood. The complete temperature history was therefore estimated with a previously developed optical-thermal model and validated using long wave infra-red imaging. Short beam strengths equivalent to conventional manufacturing methods were found for placement rates of 400 mm/s. Failure modes of the samples were elucidated by scanning electron microscopy of the fracture surfaces. Signs of degradation were observed on samples prepared with a 600 °C process temperature at 100 mm/s, however none was evidenced at 400 mm/s for the same process temperature.

Processing of thermoplastic matrix composites through automated fiber placement and tape laying methods: A review

Abstract: Fiber-reinforced composite materials are replacing metallic components due to their higher specific strength and stiffness. Automation and thermoplastics emerged to overcome the time and labor inte...