Wook Jo

Bio: Wook Jo is an academic researcher from Ulsan National Institute of Science and Technology. The author has contributed to research in topics: Ferroelectricity & Dielectric. The author has an hindex of 61, co-authored 185 publications receiving 14882 citations. Previous affiliations of Wook Jo include EPCOS AG & Seoul National University.

Perspective on the Development of Lead-free Piezoceramics

Abstract: A large body of work has been reported in the last 5 years on the development of lead-free piezoceramics in the quest to replace lead–zirconate–titanate (PZT) as the main material for electromechanical devices such as actuators, sensors, and transducers. In specific but narrow application ranges the new materials appear adequate, but are not yet suited to replace PZT on a broader basis. In this paper, general guidelines for the development of lead-free piezoelectric ceramics are presented. Suitable chemical elements are selected first on the basis of cost and toxicity as well as ionic polarizability. Different crystal structures with these elements are then considered based on simple concepts, and a variety of phase diagrams are described with attractive morphotropic phase boundaries, yielding good piezoelectric properties. Finally, lessons from density functional theory are reviewed and used to adjust our understanding based on the simpler concepts. Equipped with these guidelines ranging from atom to phase diagram, the current development stage in lead-free piezoceramics is then critically assessed.

Transferring lead-free piezoelectric ceramics into application

Abstract: After twenty years of partly quiet and ten years of partly enthusiastic research into lead-free piezoceramics there are now clear prospects for transfer into applications in some areas. This mimics prior research into eliminating lead from other technologies that resulted in restricted lead use in batteries and dwindling use in other applications. A figure of merit analysis for key devices is presented and used to contrast lead-containing and lead-free piezoceramics. A number of existing applications emerge, where the usage of lead-free piezoceramics may be envisaged in the near future. A sufficient transition period to ensure reliability, however, is required. The use of lead-free piezoceramics for demanding applications with high reliability, displacements and frequency as well as a wide temperature range appears to remain in the distant future. New devices are outlined, where the figure of merit suggests skipping lead-containing piezoceramics altogether. Suggestions for the next pertinent research requirements are provided.

Giant electric-field-induced strains in lead-free ceramics for actuator applications – status and perspective

Abstract: In response to the current environmental regulations against the use of lead in daily electronic devices, a number of investigations have been performed worldwide in search for alternative piezoelectric ceramics that can replace the market-dominating lead-based ones, representatively Pb(Zr x Ti1-x )O3 (PZT)-based solid solutions. Selected systems of potential importance such as chemically modified and/or crystallographically textured (K, Na)NbO3 and (Bi1/2Na1/2)TiO3-based solid solutions have been developed. Nevertheless, only few achievements have so far been introduced to the marketplace. A recent discovery has greatly extended our tool box for material design by furnishing (Bi1/2Na1/2)TiO3-based ceramics with a reversible phase transition between an ergodic relaxor state and a ferroelectric with the application of electric field. This paired the piezoelectric effect with a strain-generating phase transition and extended opportunities for actuator applications in a completely new manner. In this contribution, we will present the status and perspectives of this new class of actuator ceramics, aiming at covering a wide spectrum of topics, i.e., from fundamentals to practice.

On the phase identity and its thermal evolution of lead free (Bi1/2Na1/2)TiO3-6 mol% BaTiO3

Abstract: Temperature-dependent dielectric permittivity of 0.94(Bi1/2Na1/2)TiO3-0.06BaTiO3 (BNT-6BT) lead-free piezoceramics was studied to disentangle the existing unclear issues over the crystallographic aspects and phase stability of the system. Application of existing phenomenological relaxor models enabled the relaxor contribution to the entire dielectric permittivity spectra to be deconvoluted. The deconvoluted data in comparison with the temperature-dependent dielectric permittivity of a classical perovskite relaxor, La-modified lead zirconate titanate, clearly suggest that BNT-6BT belongs to the same relaxor category, which was also confirmed by a comparative study on the temperature- dependent polarization hysteresis loops of both materials. Based on these results, we propose that the low-temperature dielectric anomaly does not involve any phase transition such as ferroelectric- to-antiferroelectric. Supported by transmission electron microscopy and X-ray diffraction experiments at ambient temperature, we propose that the commonly observed two dielectric anomalies are attributed to thermal evolution of ferroelectric polar nanoregions of R3c and P4bm symmetry, which coexist nearly throughout the entire temperature range and reversibly transform into each other with temperature.

Origin of the large strain response in (K0.5Na0.5)NbO3-modified (Bi0.5Na0.5)TiO3―BaTiO3 lead-free piezoceramics

Abstract: The mechanism of the giant unipolar strain recently observed in a lead-free piezoceramic, 0.92(Bi0.5Na0.5)TiO3-0.06BaTiO(3)-0.02(K0.5Na0.5)NbO3 [S.-T. Zhang, A. B. Kounga, E. Aulbach, H. Ehrenberg, and J. Rodel, Appl. Phys. Lett. 91, 112906 (2007) was investigated. The validity of the previously proposed mechanism that the high strain comes both from a significant volume change during the field-induced phase transition, from an antiferroelectric to a ferroelectric phase and the domain contribution from the induced ferroelectric phase was examined. Monitoring the volume changes from the simultaneously measured longitudinal and transverse strains on disk-shaped samples showed that the phase transition in this specific material does not involve any notable volume change, which indicates that there is little contribution from a volume change due to the phase transition to the total strain response. Temperature dependent hysteresis measurements on unpoled samples of a nearby ferroelectric composition, 0.93(Bi0.5Na0.5)TiO3-0.06BaTiO(3) -0.01(K0.5Na0.5)NbO3 demonstrated that the origin of the large strain is due to the presence of a nonpolar phase that brings the system back to its unpoled state once the applied electric field is removed, which leads to a large unipolar strain.

Perspective on the Development of Lead-free Piezoceramics

Abstract: A large body of work has been reported in the last 5 years on the development of lead-free piezoceramics in the quest to replace lead–zirconate–titanate (PZT) as the main material for electromechanical devices such as actuators, sensors, and transducers. In specific but narrow application ranges the new materials appear adequate, but are not yet suited to replace PZT on a broader basis. In this paper, general guidelines for the development of lead-free piezoelectric ceramics are presented. Suitable chemical elements are selected first on the basis of cost and toxicity as well as ionic polarizability. Different crystal structures with these elements are then considered based on simple concepts, and a variety of phase diagrams are described with attractive morphotropic phase boundaries, yielding good piezoelectric properties. Finally, lessons from density functional theory are reviewed and used to adjust our understanding based on the simpler concepts. Equipped with these guidelines ranging from atom to phase diagram, the current development stage in lead-free piezoceramics is then critically assessed.

Consolidation/synthesis of materials by electric current activated/assisted sintering

Abstract: This review article aims to provide an updated and comprehensive description of the development of the Electric Current Activated/assisted Sintering technique (ECAS) for the obtainment of dense materials including nanostructured ones. The use of ECAS for pure sintering purposes, when starting from already synthesized powders promoters, and to obtain the desired material by simultaneously performing synthesis and consolidation in one-step is reviewed. Specifically, more than a thousand papers published on this subject during the past decades are taken into account. The experimental procedures, formation mechanisms, characteristics, and functionality of a wide spectrum of dense materials fabricated by ECAS are presented. The influence of the most important operating parameters (i.e. current intensity, temperature, processing time, etc.) on product characteristics and process dynamics is reviewed for a large family of materials including ceramics, intermetallics, metal–ceramic and ceramic–ceramic composites. In this review, systems where synthesis and densification stages occur simultaneously, i.e. a fully dense product is formed immediately after reaction completion, as well as those ones for which a satisfactory densification degree is reached only by maintaining the application of the electric current once the full reaction conversion is obtained, are identified. In addition, emphasis is given to the obtainment of nanostructured dense materials due to their rapid progress and wide applications. Specifically, the effect of mechanical activation by ball milling of starting powders on ECAS process dynamics and product characteristics (i.e. density and microstructure) is analysed. The emerging theme from the large majority of the reviewed investigations is the comparison of ECAS over conventional methods including pressureless sintering, hot pressing, and others. Theoretical analysis pertaining to such technique is also proposed following the last results obtained on this topic.

Transferring lead-free piezoelectric ceramics into application

Abstract: After twenty years of partly quiet and ten years of partly enthusiastic research into lead-free piezoceramics there are now clear prospects for transfer into applications in some areas. This mimics prior research into eliminating lead from other technologies that resulted in restricted lead use in batteries and dwindling use in other applications. A figure of merit analysis for key devices is presented and used to contrast lead-containing and lead-free piezoceramics. A number of existing applications emerge, where the usage of lead-free piezoceramics may be envisaged in the near future. A sufficient transition period to ensure reliability, however, is required. The use of lead-free piezoceramics for demanding applications with high reliability, displacements and frequency as well as a wide temperature range appears to remain in the distant future. New devices are outlined, where the figure of merit suggests skipping lead-containing piezoceramics altogether. Suggestions for the next pertinent research requirements are provided.