[신간의 별자리x] 우리/미술, 그리고 ‘슬픔의 박물관’

Thank you for reading rfid handbook fundamentals and applications in contactless smart cards and identification. As you may know, people have search numerous times for their chosen novels like this rfid handbook fundamentals and applications in contactless smart cards and identification, but end up in malicious downloads. Rather than reading a good book with a cup of coffee in the afternoon, instead they juggled with some malicious bugs inside their laptop.

Rfid Handbook Fundamentals And Applications In Contactless Smart Cards And Identification

Before the emergence of ultra-wideband (UWB) radios, widely used wireless communications were based on sinusoidal carriers, and impulse technologies were employed only in specific applications (e.g. radar). In 2002, the Federal Communication Commission (FCC) allowed unlicensed operation between 3.1–10.6 GHz for UWB communication, using a wideband signal format with a low EIRP level (−41.3dBm/MHz). UWB communication systems then emerged as an alternative to narrowband systems and significant effort in this area has been invested at the regulatory, commercial, and research levels.

IEEE Transactions on Microwave Theory and Techniques and Antennas and Propagation Announce a Joint Special Issue on Ultra-Wideband (UWB) Technology

The programmable nature of smart textiles makes them an indispensable part of an emerging new technology field. Smart textile-integrated microelectronic systems (STIMES), which combine microelectronics and technology such as artificial intelligence and augmented or virtual reality, have been intensively explored. A vast range of research activities have been reported. Many promising applications in healthcare, the internet of things (IoT), smart city management, robotics, etc., have been demonstrated around the world. A timely overview and comprehensive review of progress of this field in the last five years are provided. Several main aspects are covered: functional materials, major fabrication processes of smart textile components, functional devices, system architectures and heterogeneous integration, wearable applications in human and nonhuman-related areas, and the safety and security of STIMES. The major types of textile-integrated nonconventional functional devices are discussed in detail: sensors, actuators, displays, antennas, energy harvesters and their hybrids, batteries and supercapacitors, circuit boards, and memory devices.

Smart Textile-Integrated Microelectronic Systems for Wearable Applications

This paper presents a novel kind of patch antenna with high-selectivity filtering responses and high-gain radiation performance. The proposed antenna is mainly composed of a driven patch and a stacked patch, with its entire height being ${0.09\lambda }$ . Three shorting pins and a U-slot are embedded in the driven patch to enhance out-of-band suppression levels and skirt selectivity near the lower band-edge, whereas the stacked patch provides a sharp roll-off rate at the upper band-edge and also an enhanced gain. Without using extra filtering circuits, the proposed antenna exhibits a quasi-elliptic boresight gain response with three radiation nulls. For demonstration, an antenna is implemented covering the LTE band (2.3–2.7 GHz). The antenna achieves an average gain of 9.7 dBi within passband, and out-of-band suppression levels of more than 21 dB.

High-Gain Filtering Patch Antenna Without Extra Circuit

Dual-band bandpass filters using novel stub-loaded resonators (SLRs) are presented in this letter. Characterized by both theoretical analysis and full-wave simulation, the proposed SLR is found to have the advantage that the even-mode resonant frequencies can be flexibly controlled whereas the odd-mode resonant frequencies are fixed. Based on the proposed SLR, a dual-band filter is implemented with three transmission zeros. To further improve the selectivity, a filter with four transmission zeros on either side of both passbands is designed by introducing spur-line. The measured results validate the proposed design.

Dual-Band Bandpass Filters Using Stub-Loaded Resonators

A low-profile, high-gain, and wideband metasurface (MS)-based filtering antenna with high selectivity is investigated in this communication. The planar MS consists of nonuniform metallic patch cells, and it is fed by two separated microstrip-coupled slots from the bottom. The separation between the two slots together with a shorting via is used to provide good filtering performance in the lower stopband, whereas the MS is elaborately designed to provide a sharp roll-off rate at upper band edge for the filtering function. The MS also simultaneously works as a high-efficient radiator, enhancing the impedance bandwidth and antenna gain of the feeding slots. To verify the design, a prototype operating at 5 GHz has been fabricated and measured. The reflection coefficient, radiation pattern, antenna gain, and efficiency are studied, and reasonable agreement between the measured and simulated results is observed. The prototype with dimensions of 1.3 $\lambda_{0}\times1.3\ \lambda_{0}\times0.06\ \lambda_{0}$ has a 10-dB impedance bandwidth of 28.4%, an average gain of 8.2 dBi within passband, and an out-of-band suppression level of more than 20 dB within a very wide stop-band.

A Low-Profile High-Gain and Wideband Filtering Antenna With Metasurface

This paper presents a novel device integrating a power divider with two bandpass filters. It is capable of splitting power and selecting frequency at the same time. The phase shift of the filter is found to be ±90° at the center frequency. Therefore, when it is matched to 70.7 Ω, it can replace the conventional quarter-wave length transmission line in the power divider. The isolation elements are loaded at the filters' open ends to get a good isolation between the output ports. As a result, both the transmission and isolation property are satisfied. The equivalent even- and odd-mode circuits of the proposed structure are analyzed and design equations are derived. They are used to guide the design of the devices. For demonstration, filter-integrated power dividers with single- and dual-band operation are implemented, respectively. Comparisons of the measured and simulated results are presented to verify the theoretical predications.

Single- and Dual-Band Power Dividers Integrated With Bandpass Filters

This paper presents a novel dual-band base station antenna array using filtering antenna elements for size miniaturization. It consists of two $1 \times 6$ subarrays arranged side by side, which are designed for Digital Cellular System (DCS: 1710–1880 MHz) and Wideband Code Division Multiple Access (WCDMA: 1920–2170 MHz) applications. The two subarrays are composed of filtering antenna elements with high in-band radiation efficiency and out-of-band radiation rejection levels. The radiation of the DCS subarray is suppressed in the WCDMA band and vice versa. Mutual coupling between the two subarrays, therefore, can be suppressed and high isolation can be obtained with reduced subarray spacing. For demonstration, a dual-band filtering antenna array is designed and fabricated. The overall width of the array is only 206 mm, which is much narrower than that of typical industrial products ( $\sim 290$ mm). An isolation of 35 dB is obtained between the two subarrays without any decoupling network. The measured antenna gains are about 14.2 and 14.5 dBi for DCS and WCDMA bands, respectively, and the 3-dB beamwidths of the horizontal radiation patterns are 65° ± 5°. In addition, null filling below the main beam in the vertical radiation patterns is realized by elaborately designing a feed network to manipulate the output magnitude and phase of each array element. The proposed array is suitable for potential base station applications.

Xiu Yin Zhang

Papers

Dual-Band Bandpass Filters Using Stub-Loaded Resonators

High-Gain Filtering Patch Antenna Without Extra Circuit

A Low-Profile High-Gain and Wideband Filtering Antenna With Metasurface

Single- and Dual-Band Power Dividers Integrated With Bandpass Filters

Dual-Band Base Station Array Using Filtering Antenna Elements for Mutual Coupling Suppression