Detection of hazardous volatile organic compounds (VOCs) by metal oxide nanostructures-based gas sensors: A review

Xin Zhou,†,‡ Songyi Lee,† Zhaochao Xu,* and Juyoung Yoon*,† †Department of Chemistry and Nanoscience, Ewha Womans University, Seoul 120-750, Republic of Korea ‡Research Center for Chemical Biology, Department of Chemistry, Yanbian University, Yanjii 133002, People’s Republic of China Key Laboratory of Separation Science for Analytical Chemistry, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, 457 Zhongshan Road, Shahekou, Dalian, Liaoning, People’s Republic of China

Recent Progress on the Development of Chemosensors for Gases.

Quasi-one dimensional metal oxide semiconductors: Preparation, characterization and application as chemical sensors

Wearable electronics is expected to be one of the most active research areas in the next decade; therefore, nanomaterials possessing high carrier mobility, optical transparency, mechanical robustness and flexibility, lightweight, and environmental stability will be in immense demand. Graphene is one of the nanomaterials that fulfill all these requirements, along with other inherently unique properties and convenience to fabricate into different morphological nanostructures, from atomically thin single layers to nanoribbons. Graphene-based materials have also been investigated in sensor technologies, from chemical sensing to detection of cancer biomarkers. The progress of graphene-based flexible gas and chemical sensors in terms of material preparation, sensor fabrication, and their performance are reviewed here. The article provides a brief introduction to graphene-based materials and their potential applications in flexible and stretchable wearable electronic devices. The role of graphene in fabricating ...

Flexible Graphene-Based Wearable Gas and Chemical Sensors

Recently, the hydrogen gas sensing properties of semiconductor oxide (SMO) nanostructures have been widely investigated. In this article, we provide a comprehensive review of the research progress in the last five years concerning hydrogen gas sensors based on SMO thin film and one-dimensional (1D) nanostructures. The hydrogen sensing mechanism of SMO nanostructures and some critical issues are discussed. Doping, noble metal-decoration, heterojunctions and size reduction have been investigated and proved to be effective methods for improving the sensing performance of SMO thin films and 1D nanostructures. The effect on the hydrogen response of SMO thin films and 1D nanostructures of grain boundary and crystal orientation, as well as the sensor architecture, including electrode size and nanojunctions have also been studied. Finally, we also discuss some challenges for the future applications of SMO nanostructured hydrogen sensors.

/pdf/hydrogen-gas-sensors-based-on-semiconductor-oxide-1acna97miv.pdf

Hydrogen Gas Sensors Based on Semiconductor Oxide Nanostructures

Aligned zinc oxide nanorods were synthesized directly via a two-step solution approach on an Al2O3 tube, and were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The zinc oxide nanorods prepared were uniform with diameters of 10–30 nm and lengths about 1.4 μm. The response Sr (= Ra/Rg) of the aligned zinc oxide nanorod sensor reached 18.29 and 10.41 to 100 ppm ethanol and hydrogen, respectively, which was a two-fold increase compared with that reported in literature, demonstrating the potential for developing stable and sensitive gas sensors.

Nanopillar ZnO gas sensor for hydrogen and ethanol

ZnO hollow sphere with porous shell has been prepared by co-precipitation method using Zn(NO 3 ) 2 ·6H 2 O and (CH 2 ) 6 N 4 as reactants, sodium citrate as surfactant. The BET surface area of as-prepared ZnO hollow sphere sample is 41.84 m 2 /g. The response of gas sensor made from the obtained ZnO hollow sphere reaches 7.4 to 10 ppm ammonia, with a response time of 10 s, implying the potential for practical applications.

Co-precipitation synthesis and gas-sensing properties of ZnO hollow sphere with porous shell

Porous alumina film on aluminum with gel-like pore wall was prepared by a two-step anodization of aluminum, and the corresponding gel-like porous film was etched in diluted NaOH solution to produce alumina nanowires in the form of densely packed alignment. The resultant alumina nanowires were reacted with NH3and evaporated aluminum at an elevated temperature to be converted into densely packed aluminum nitride (AlN) nanowires. The AlN nanowires have a diameter of 15–20 nm larger than that of the alumina nanowires due to the supplement of the additional evaporated aluminum. The results suggest that it might be possible to prepare other aluminum compound nanowires through similar process.

/pdf/fabrication-of-densely-packed-aln-nanowires-by-a-chemical-2iij2ltrou.pdf

Fabrication of Densely Packed AlN Nanowires by a Chemical Conversion of Al2O3Nanowires Based on Porous Anodic Alumina Film

A simple and low-cost method based on a two-step heat treatment of AgNO(3)/SiO(2) film has been developed for fabricating metal Ag nanoring arrays. The as-prepared nanorings have an inner diameter of 70-250 nm and an average wall thickness (namely wire diameter) of approximately 30 nm with a number density of approximately 10(9) cm(-2) on the surface of the SiO(2) matrix. X-ray diffraction (XRD) results reveal that these nanorings exhibit a face-centered cubic crystal structure. Furthermore, a new growth mechanism, namely a molten metal bubble as a self-template, is tentatively proposed for Ag nanorings.

http://iopscience.iop.org/article/10.1088/0957-4484/19/7/075608/pdf

A simple approach for large-area fabrication of Ag nanorings.

Li-organic batteries (LOBs) are promising advanced battery systems because of their unique advantages in capacity, cost, and sustainability. However, the shuttling effect of soluble organic redox intermediates and the intrinsic dissolution of small-molecular electrodes have hindered the practical application of these cells, especially under high operating temperatures. Herein, a cross-linked membrane with abundant negative charge for high-temperature LOBs is prepared via electrospinning of poly(vinyl alcohol) containing halloysite nanotubes (HNTs). The translocation of negatively charged organic intermediates can be suppressed by the electronic repulsion and the cross-linked network while the positively charged Li+ are maintained, which is attributed to the intrinsic electronegativity of HNTs and their well-organized and homogeneous distribution in the PVA matrix. A battery using a PVA/HNT composite separator (EPH-10) and an anthraquinone (AQ) cathode exhibits a high initial discharge capacity of 231.6 mAh g-1 and an excellent cycling performance (91.4% capacity retention, 300 cycles) at 25 °C. Even at high temperatures (60 and 80 °C), its capacity retention is more than 89.2 and 80.4% after 100 cycles, respectively. Our approach demonstrates the potential of the EPH-10 composite membrane as a separator for high-temperature LOB applications.

Yue-Qin Duan

Papers

Nanopillar ZnO gas sensor for hydrogen and ethanol

Co-precipitation synthesis and gas-sensing properties of ZnO hollow sphere with porous shell

Fabrication of Densely Packed AlN Nanowires by a Chemical Conversion of Al2O3Nanowires Based on Porous Anodic Alumina Film

A simple approach for large-area fabrication of Ag nanorings.

Cross-Linked PVA/HNT Composite Separator Enables Stable Lithium-Organic Batteries under Elevated Temperature.