Yury Gogotsi

Bio: Yury Gogotsi is an academic researcher from Drexel University. The author has contributed to research in topics: MXenes & Carbon. The author has an hindex of 171, co-authored 956 publications receiving 144520 citations. Previous affiliations of Yury Gogotsi include Qatar Airways & Clemson University.

Direct observation of active material interactions in flowable electrodes using X-ray tomography

Abstract: Understanding electrical percolation and charging mechanisms in electrochemically active biphasic flowable electrodes is critical for enabling scalable deionization (desalination) and energy storage. Flowable electrodes are dynamic material systems which store charge (remove ions) and have the ability to flow. This flow process can induce structural changes in the underlying material arrangement and result in transient and non-uniform material properties. Carbon-based suspensions are opaque, multi-phase, and three dimensional, and thus prior characterization of the structural properties has been limited to indirect methods (electrochemical and rheology). Herein, a range of mixed electronic and ionically conducting suspensions are evaluated to determine their static structure, function, and properties, utilizing synchrotron radiation X-ray tomographic microscopy (SRXTM). The high brilliance of the synchrotron light enables deconvolution of the liquid and solid phases. Reconstruction of the solid phase reveals agglomeration cluster volumes between 10 μm3 and 103 μm3 (1 pL) for low loaded samples (5 wt% carbon). The largest agglomeration cluster in the low loaded sample (5 wt%) occupied only 3% of the reconstructed volume whereas samples loaded with 10 wt% activated carbon demonstrated electrically connected clusters that occupied 22% of the imaged region. The highly loaded samples (20 wt%) demonstrated clusters of the order of a microliter, which accounted for 63–85% of the imaged region. These results demonstrate a capability for discerning the structural properties of biphasic systems utilizing SRXTM techniques, and show that discontinuity in the carbon particle networks induces decreased material utilization in low-loaded flowable electrodes.

Sculpting Liquids with Two-Dimensional Materials: The Assembly of Ti3C2Tx MXene Sheets at Liquid-Liquid Interfaces.

Abstract: The self-assembly of nanoscale materials at the liquid-liquid interface allows for fabrication of three-dimensionally structured liquids with nearly arbitrary geometries and tailored electronic, optical, and magnetic properties. Two-dimensional (2D) materials are highly anisotropic, with thicknesses on the order of a nanometer and lateral dimensions upward of hundreds of nanometers to micrometers. Controlling the assembly of these materials has direct implications for their properties and performance. We here describe the interfacial assembly and jamming of Ti3C2Tx MXene nanosheets at the oil-water interface. Planar, as well as complex, programmed three-dimensional all-liquid objects are realized. Our approach presents potential for the creation of all-liquid 3D-printed devices for possible applications in all-liquid electrochemical and energy storage devices and electrically active, all-liquid fluidics that exploits the versatile structure, functionality, and reconfigurability of liquids.

Solvent Polarity Governs Ion Interactions and Transport in a Solvated Room-Temperature Ionic Liquid

Abstract: We explore the influence of the solvent dipole moment on cation–anion interactions and transport in 1-butyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl), [BMIM+][Tf2N–]. Free energy profiles derived from atomistic molecular dynamics (MD) simulations show a correlation of the cation–anion separation and the equilibrium depth of the potential of mean force with the dipole moment of the solvent. Correlations of the ion diffusivity with the dipole moment and the concentration of the solvent were further demonstrated by classical MD simulations. Quasi-elastic neutron scattering experiments with deuterated solvents reveal a complex picture of nanophase separation into the ionic liquid-rich and solvent-rich phases. The experiment corroborates the trend of concentration- and dipole moment-dependent enhancement of ion mobility by the solvent, as suggested by the simulations. Despite the considerable structural complexity of ionic liquid–solvent mixtures, we can rationalize and generalize the trends governing ...

Can Anions Be Inserted into MXene

Abstract: Despite the continuous progress in the research and development of Ti3C2Tx (MXene) electrodes for high-power batteries and supercapacitor applications, the role of the anions in the electrochemical energy storage and their ability to intercalate between the MXene sheets upon application of positive voltage have not been clarified. A decade after the discovery of MXenes, the information about the possibility of anion insertion into the restacked MXene electrode is still being questioned. Since the positive potential stability range in diluted aqueous electrolytes is severely limited by anodic oxidation of the Ti, the possibility of anion insertion was evaluated in concentrated aqueous electrolyte solutions and aprotic electrolytes as well. To address this issue, we have conducted in situ gravimetric electrochemical quartz crystal microbalance with dissipation monitoring (EQCM-D) measurements in highly concentrated LiCl and LiBr electrolytes, which enable a significant extension of the operation range of the MXene electrodes toward positive potentials. Also, halogens are among the smallest anions and should be easier to intercalate between MXene layers, in comparison to multiatomic anions. On the basis of mass change variations in the positive voltage range and complementary density functional theory calculations, it was demonstrated that insertion of anionic species into MXene, within the range of potentials of interest for capacitive energy storage, is not likely to occur. This can be explained by the strong negative charge on Ti3C2Tx sheets terminated by functional groups.

Titanium dioxide-coated nanofibers for advanced filters

Abstract: This article reports on titanium dioxide (TiO2)-coated nanofibers deposited on a filter surface by the electrospinning process. After depositing a micrometer-thick film of polyamide 11 nanofibers on polypropylene fabric, TiO2 nanoparticles can be directly electrosprayed onto the nanofibers. X-ray diffraction and Raman spectroscopy showed minimal change in the phase composition (anatase and rutile) and no change in the particle size of nanocrystalline TiO2 after coating. Scanning electron microscopy demonstrated that nanofibers were uniformly coated by titanium dioxide nanoparticles without agglomeration. TiO2-coated filters showed excellent photocatalytic-bactericidal activity and photo-induced hydrophilicity.

I and i

Abstract: There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality. Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

Fast parallel algorithms for short-range molecular dynamics

Abstract: Three parallel algorithms for classical molecular dynamics are presented. The first assigns each processor a fixed subset of atoms; the second assigns each a fixed subset of inter-atomic forces to compute; the third assigns each a fixed spatial region. The algorithms are suitable for molecular dynamics models which can be difficult to parallelize efficiently—those with short-range forces where the neighbors of each atom change rapidly. They can be implemented on any distributed-memory parallel machine which allows for message-passing of data between independently executing processors. The algorithms are tested on a standard Lennard-Jones benchmark problem for system sizes ranging from 500 to 100,000,000 atoms on several parallel supercomputers--the nCUBE 2, Intel iPSC/860 and Paragon, and Cray T3D. Comparing the results to the fastest reported vectorized Cray Y-MP and C90 algorithm shows that the current generation of parallel machines is competitive with conventional vector supercomputers even for small problems. For large problems, the spatial algorithm achieves parallel efficiencies of 90% and a 1840-node Intel Paragon performs up to 165 faster than a single Cray C9O processor. Trade-offs between the three algorithms and guidelines for adapting them to more complex molecular dynamics simulations are also discussed.

疟原虫var基因转换速率变化导致抗原变异[英]／Paul H, Robert P, Christodoulou Z, et al//Proc Natl Acad Sci U S A

Abstract: 抗原变异可使得多种致病微生物易于逃避宿主免疫应答。表达在感染红细胞表面的恶性疟原虫红细胞表面蛋白1（PfPMP1）与感染红细胞、内皮细胞、树突状细胞以及胎盘的单个或多个受体作用，在黏附及免疫逃避中起关键的作用。每个单倍体基因组var基因家族编码约60种成员，通过启动转录不同的var基因变异体为抗原变异提供了分子基础。

Materials for electrochemical capacitors

Abstract: Electrochemical capacitors, also called supercapacitors, store energy using either ion adsorption (electrochemical double layer capacitors) or fast surface redox reactions (pseudo-capacitors). They can complement or replace batteries in electrical energy storage and harvesting applications, when high power delivery or uptake is needed. A notable improvement in performance has been achieved through recent advances in understanding charge storage mechanisms and the development of advanced nanostructured materials. The discovery that ion desolvation occurs in pores smaller than the solvated ions has led to higher capacitance for electrochemical double layer capacitors using carbon electrodes with subnanometre pores, and opened the door to designing high-energy density devices using a variety of electrolytes. Combination of pseudo-capacitive nanomaterials, including oxides, nitrides and polymers, with the latest generation of nanostructured lithium electrodes has brought the energy density of electrochemical capacitors closer to that of batteries. The use of carbon nanotubes has further advanced micro-electrochemical capacitors, enabling flexible and adaptable devices to be made. Mathematical modelling and simulation will be the key to success in designing tomorrow's high-energy and high-power devices.