Development of Solar‐Pumped Lasers and Its Application

Metal nanoparticles have become attractive as original materials for nano-inks and nano-pastes, which are used in printed electronics. Synthesizing various metal nanoparticles has been researched. We investigated the possibility of reducing metal oxide in a metal by using high-voltage pulses in this paper. This method should save electrical consumption power compared with conventional methods that use high-temperature and high-pressure plasma such as arc discharge. Reduced Al nanoparticles were obtained by applying high-voltage pulses to solutions. By analyzing elements and the composition of reduced Al nanoparticles by STEM and EDX, a large amount of reduced Al nanoparticles with diameters of a few 100 nm and thin oxide film of around 1 nm on metal surfaces were produced in experiments for reducing Al oxide. It was found from hydrogen generation using reduced Al nanoparticles by applying high-voltage pulses to solutions to evaluate reduction rate that a high reduction efficiency of 97% was obtained at maximum. We concluded that using high-voltage pulses for reduction can be suitably applied to printed electronics because the oxide film on reduced Al nanoparticles is thin. Also, because this method is similar to laser ablation in liquids using pulse lasers, the similarities were discussed in this paper.

Production of Reduced Al Nanoparticles from Al Oxide by Applying High Voltage Pulses to Solutions

Reduction in the skin effect for the sintered Si nanopolycrystalline body as an electricity conductor at a high frequency due to its nano-structure was studied. Singular vanishing of electrical resistances near a local high magnetic harmonic frequency of a few MHz was observed. This phenomenon has not been observed for conventional ferromagnetic metals. The measured electrical resistances changed to almost 0 m{\Omega} at room temperature. At the same time, negative resistance of the sintered Si nano-polycrystalline body was observed. It will be applicable to electronic transmittance lines or semiconductors. Numerical calculation was also performed on the electrical resistance with frequency dependency while considering the electric field and magnetic field in the sintered Si nanopolycrystalline body. The calculation could explain the variation of the relative permittivity of the Si nanopolycrystalline and the phenomenon for vanishing the resistivity at frequency of MHz theoretically. Reduced Si nanoparticles from SiO2 powder were synthesized by laser ablation in liquid. A Si nano-polycrystalline body made of the reduced Si nanoparticles was fabricated. It was found by measuring the magnetization property of the body that the sintered Si nano-polycrystalline body has ferromagnetism. High-density dangling bonds cause the sintered Si nanopolycrystalline to have ferromagnetism. In this study, the density of the unpaired electrons in the sintered Si nanopolycrystalline was observed using ESR. It has been clarified that the Si nanopowder and the sintered Si nanopolycrystalline have numerous dangling bonds. Both densities of the dangling bonds were evaluated.

Appearance of ferromagnetism property for Si nano-polycrystalline body and vanishing of electrical resistances at local high frequencies

Development on Solar-pumped Lasers and its Application

Reduction in the skin effect for the sintered Si nanopolycrystalline body as an electricity conductor at a high frequency due to its nanostructure was studied. Singular disappearance of electrical resistances near a local high magnetic harmonic frequency of a few MHz was observed. This phenomenon has not been observed for conventional ferromagnetic metals. The measured electrical resistances changed to almost 0 mΩ at room temperature. At the same time, negative resistance of the sintered Si nanopolycrystalline body was observed. It will be applicable to electronic transmittance lines or semiconductors. Numerical calculation was also performed on the electrical resistance with frequency dependency while considering the electric field and magnetic field in the sintered Si nanopolycrystalline body. The experimental and calculated results are compared. The calculation could explain the variation of the relative permittivity of the Si nanopolycrystalline body and the phenomenon for the theoretical disappearance of the resistivity at the MHz frequency. Reduced Si nanoparticles from SiO2 powder were synthesized by laser ablation in liquid. A Si nanopolycrystalline body made of the reduced Si nanoparticles was fabricated. It was found by measuring the magnetization property of the body of the sintered Si nanopolycrystalline body which is ferromagnetic. Dangling bonds (unpaired electrons) have long been known to occur due to defects in Si crystals. Perfect Si without defective crystals has no dangling bonds. However, Si nanoparticles have many dangling bonds. High-density dangling bonds cause the sintered Si nanopolycrystalline body to have ferromagnetism. In this study, the density of the unpaired electrons in the sintered Si nanopolycrystalline body was observed using ESR. It has been clarified that the Si nanopowder and the sintered Si nanopolycrystalline body have numerous dangling bonds. Both densities of the dangling bonds were evaluated.

Appearance of Ferromagnetic Property for Si Nanopolycrystalline Body and Vanishing of Electrical Resistances at Local High Frequencies

Reduced iron, aluminum, copper, and magnesium nanoparticles were produced from iron oxide (Fe3O4), aluminum oxide (Al2O3), copper oxide (CuO), and magnesium oxide (MgO) powders by using laser ablation in liquids, and nanopastes were synthesized with the reduced iron, aluminum, copper, and magnesium nanoparticles. The nanopastes were sintered by using a continuous-wave fiber laser in air atmosphere. The laser-sintered nanopastes consist of polycrystalline metal. The structures of the laser-sintered metal nanopastes were analyzed by SEM and EDX, and their resistivities were evaluated by four-terminal method. The metal nanopastes sintered by hot plate have 2.5- to 11-times-higher resistivities than those of common metals fabricated in blast furnaces. Moreover, the laser-sintered metal nanopastes have 9.5- to 45-times-higher resistivities than those of common metals fabricated in blast furnaces.

/pdf/electrical-property-of-laser-sintered-nanopastes-with-i8kztbtqre.pdf

Yuuki Koga

Papers

Electrical Property of Laser-Sintered Nanopastes with Reduced Metal Nanoparticles Prepared by Laser Ablation in Liquids