Zongyuan Liu

Bio: Zongyuan Liu is an academic researcher from Huazhong University of Science and Technology. The author has contributed to research in topics: Light-emitting diode & LED lamp. The author has an hindex of 18, co-authored 51 publications receiving 1456 citations.

Optical Analysis of Color Distribution in White LEDs With Various Packaging Methods

Abstract: Uniform color distribution is essential for the packaging of light emitting diodes (LEDs). The Monte Carlo ray tracing method is applied to analyze the color distribution of white LEDs. Five packaging methods are investigated and the location of phosphor layer is varied. Results reveal that the packaging method is the primary factor affecting the color distribution and a nonreflector packaging method presents better color uniformity. The location of phosphor has a small impact on the color uniformity but remote location, if too far, can reduce the uniformity significantly. The reduction of color uniformity may exceed 88%.

Design of compact freeform lens for application specific light-emitting diode packaging

Abstract: Application specific LED packaging (ASLP) is an emerging technology for high performance LED lighting. We introduced a practical design method of compact freeform lens for extended sources used in ASLP. A new ASLP for road lighting was successfully obtained by integrating a polycarbonate compact freeform lens of small form factor with traditional LED packaging. Optical performance of the ASLP was investigated by both numerical simulation based on Monte Carlo ray tracing method and experiments. Results demonstrated that, comparing with traditional LED module integrated with secondary optics, the ASLP had advantages of much smaller size in volume (approximately 1/8), higher system lumen efficiency (approximately 8.1%), lower cost and more convenience for customers to design and assembly, enabling possible much wider applications of LED for general road lighting. Tolerance analyses were also conducted. Installation errors of horizontal and vertical deviations had more effects on the shape and uniformity of radiation pattern compared with rotational deviation. The tolerances of horizontal, vertical and rotational deviations of this lens were 0.11 mm, 0.14 mm and 2.4 degrees respectively, which were acceptable in engineering.

Measurement and numerical studies of optical properties of YAG:Ce phosphor for white light-emitting diode packaging

Abstract: The optical properties of YAG:Ce phosphor were measured by a double-integrating-sphere system and calculated by Mie theory and Monte Carlo ray tracing to provide precise optical characterizations of YAG:Ce phosphor for white light-emitting diode (LED) packaging design. Measurement results showed that the phosphor presents strong absorption for blue light, high reflection for yellow light, and an isotropic emission pattern of converted light. The conversion efficiency and quantum efficiency for the saturated phosphor are around 70% and 87%, respectively. Based on the measurement results, the absorption coefficient, scattering coefficient, and anisotropy factor of the phosphor calculated by Mie theory were compared with those calculated by ray-tracing simulation to modify Mie theory to find a reasonable method that can easily obtain the optical constants of YAG:Ce phosphor. Comparisons revealed that Mie theory can predict the variation of the optical constants of phosphor, but the absorption and scattering cross sections should be multiplied with two fitting parameters. The fitting parameters have been given in this study and can be obtained by testing packaged LEDs with different phosphor concentrations.

Precise optical modeling of blue light-emitting diodes by Monte Carlo ray-tracing

Abstract: Precise optical modeling of blue light-emitting diodes (LEDs) is constructed by reasonable optical parameters and Monte Carlo ray-tracing with the capability of precisely predicting light extraction and radiation pattern for both bare LED and packaged LED. Refractive indices and absorption coefficients of LED materials are determined by abundant references and comparisons between simulations and experiments. Surface roughness is considered in the optical model to improve the simulation precision. The simulation precisions are excellent for both bare blue LEDs (>96.5% for light extraction and >99% for radiation pattern) and packaged blue LEDs (>98.5% for both light extraction and radiation pattern).

Status and prospects for phosphor-based white LED packaging

Abstract: The status and prospects for high-power, phosphor-based white light-emitting diode (LED) packaging have been presented. A system view for packaging design is proposed to address packaging issues. Four aspects of packaging are reviewed: optical control, thermal management, reliability and cost. Phosphor materials play the most important role in light extraction and color control. The conformal coating method improves the spatial color distribution (SCD) of LEDs. High refractive index (RI) encapsulants with high transmittance and modified surface morphology can enhance light extraction. Multi-phosphor-based packaging can realize the control of correlated color temperature (CCT) with high color rendering index (CRI). Effective thermal management can dissipate heat rapidly and reduce thermal stress caused by the mismatch of the coefficient of thermal expansion (CTE). Chip-on-board (CoB) technology with a multilayer ceramic substrate is the most promising method for high-power LED packaging. Low junction temperature will improve the reliability and provide longer life. Advanced processes, precise fabrication and careful operation are essential for high reliability LEDs. Cost is one of the biggest obstacles for the penetration of white LEDs into the market for general illumination products. Mass production in terms of CoB, system in packaging (SiP), 3D packaging and wafer level packaging (WLP) can reduce the cost significantly, especially when chip cost is lowered by using a large wafer size.

Fast parallel algorithms for short-range molecular dynamics

Abstract: Three parallel algorithms for classical molecular dynamics are presented. The first assigns each processor a fixed subset of atoms; the second assigns each a fixed subset of inter-atomic forces to compute; the third assigns each a fixed spatial region. The algorithms are suitable for molecular dynamics models which can be difficult to parallelize efficiently—those with short-range forces where the neighbors of each atom change rapidly. They can be implemented on any distributed-memory parallel machine which allows for message-passing of data between independently executing processors. The algorithms are tested on a standard Lennard-Jones benchmark problem for system sizes ranging from 500 to 100,000,000 atoms on several parallel supercomputers--the nCUBE 2, Intel iPSC/860 and Paragon, and Cray T3D. Comparing the results to the fastest reported vectorized Cray Y-MP and C90 algorithm shows that the current generation of parallel machines is competitive with conventional vector supercomputers even for small problems. For large problems, the spatial algorithm achieves parallel efficiencies of 90% and a 1840-node Intel Paragon performs up to 165 faster than a single Cray C9O processor. Trade-offs between the three algorithms and guidelines for adapting them to more complex molecular dynamics simulations are also discussed.

Light-emitting diodes

Abstract: Light-Emitting Diodes. (Monographs in Electrical and Electronic Engineering.) By A. A. Bergh and P. J. Dean. Pp. viii+591. (Clarendon: Oxford; Oxford University: London, 1976.) £22.

Reliability Engineering and System Safety

Abstract: This paper presents a polynomial dimensional decomposition (PDD) method for global sensitivity analysis of stochastic systems subject to independent random input following arbitrary probability distributions. The method involves Fourier-polynomial expansions of lower-variate component functions of a stochastic response by measure-consistent orthonormal polynomial bases, analytical formulae for calculating the global sensitivity indices in terms of the expansion coefficients, and dimension-reduction integration for estimating the expansion coefficients. Due to identical dimensional structures of PDD and analysis-of-variance decomposition, the proposed method facilitates simple and direct calculation of the global sensitivity indices. Numerical results of the global sensitivity indices computed for smooth systems reveal significantly higher convergence rates of the PDD approximation than those from existing methods, including polynomial chaos expansion, random balance design, state-dependent parameter, improved Sobol’s method, and sampling-based methods. However, for non-smooth functions, the convergence properties of the PDD solution deteriorate to a great extent, warranting further improvements. The computational complexity of the PDD method is polynomial, as opposed to exponential, thereby alleviating the curse of dimensionality to some extent. Mathematical modeling of complex systems often requires sensitivity analysis to determine how an output variable of interest is influenced by individual or subsets of input variables. A traditional local sensitivity analysis entails gradients or derivatives, often invoked in design optimization, describing changes in the model response due to the local variation of input. Depending on the model output, obtaining gradients or derivatives, if they exist, can be simple or difficult. In contrast, a global sensitivity analysis (GSA), increasingly becoming mainstream, characterizes how the global variation of input, due to its uncertainty, impacts the overall uncertain behavior of the model. In other words, GSA constitutes the study of how the output uncertainty from a mathematical model is divvied up, qualitatively or quantitatively, to distinct sources of input variation in the model [1].

White light-emitting diodes: History, progress, and future

Abstract: About twenty years ago, in the autumn of 1996, the first white light-emitting diodes (LEDs) were offered for sale. These then-new devices ushered in a new era in lighting by displacing lower-efficiency conventional light sources including Edison's venerable incandescent lamp as well as the Hg-discharge-based fluorescent lamp. We review the history of the conception, improvement, and commercialization of the white LED. Early models of white LEDs already exceeded the efficiency of low-wattage incandescent lamps, and extraordinary progress has been made during the last 20 years. The review also includes a discussion of advances in blue LED chips, device architecture, light extraction, and phosphors. Finally, we offer a brief outlook on opportunities provided by smart LED technology.