Cabot Corporation

About: Cabot Corporation is a(n) company organization based out in Boston, Massachusetts, United States. It is known for research contribution in the topic(s): Carbon black & Carbon. The organization has 1279 authors who have published 1399 publication(s) receiving 36736 citation(s).

Effect of Polymer-Filler and Filler-Filler Interactions on Dynamic Properties of Filled Vulcanizates

Abstract: In the past few years, an enormous amount of work has been reported on the progress in the application of conventional fillers and the development of new products to improve the reinforcement of rubber, dynamic properties in particular. While all agree that the filler as one of the main components of the filled-rubber composite, has a very important role in improving the dynamic performances of the rubber products; many new ideas, theories, practices, phenomena, and observations about how and especially why the filler alters the dynamic stress-strain response have been presented. This, of course, suggests that not only is the real world of the filled rubber complex and sophisticated but also multiple mechanisms may be involved. However, it must be admitted that the possibility exists for explaining the effect of all fillers on rubber properties ultimately in similar and relatively nonspecific terms, i.e., the phenomenon related to all filler parameters should follow a general rule or principle. I...

Novel elastomer composites, method and apparatus

Abstract: Elastomer composites are produced by novel continuous flow methods and apparatus in which fluid streams of particulate filler and elastomer latex are fed to the mixing zone of a coagulum reactor to form a mixture in semi-confined flow continuously from the mixing zone through a coagulum zone to a discharge end of the reactor. The particulate filler fluid is fed under high pressure to the mixing zone, such as to form a jet stream to entrain elastomer latex fluid sufficiently energetically to substantially completely coagulate the elastomer with the particulate filler prior to the discharge end. Highly efficient and effective elastomer coagulation is achieved without the need for a coagulation step involving exposure to acid or salt solution or the like. Novel elastomer composites are produced. Such novel elastomer composites may be cured or uncured, and combine material properties, such as choice of filler, elastomer, level of filler loading, and macro-dispersion, not previously achieved.

Nitropyrenes: isolation, identificaton, and reduction of mutagenic impurities in carbon black and toners.

Abstract: Extracts of selected xerographic toners and copies were found to be mutagenic in the Salmonella assay. The activity was independent of the xerographic hardware and process and was traced to nitropyrenes present as impurities in the carbon black, the toner colorant. Manufacturing process changes resulted in a substantial reduction of the nitropyrene content of the carbon black and thus in the mutagenicity of the corresponding toners. Nitropyrenes are potent frameshift mutagens, and possible mechanisms for their biological action are discussed.

Effect of Carbon Black on Dynamic Properties of Rubber Vulcanizates

Abstract: The term dynamic properties as applied to elastomers refers to the response to periodic or transient forces which do not cause failure or appreciable fatigue (permanent change of properties) during the investigation. Generally this is limited to vulcanizates subjected to deformations not exceeding about 25%; and generally the dynamic properties are measured after several cycles or (in a transient experiment such as resilience) after several preconditioning transients, so that the Mullins effect or difference between first and second strain cycles is not of consequence. Thus, dynamic properties represent the viscoelastic properties of vulcanizates at deformations below about 25%, after reaching a pseudo-equilibrium state. The dynamic properties of rubber are altered tremendously by the addition of a filler. The scope of this article is restricted to the dynamic properties of rubber vulcanizates with carbon black as a filler. The effect covered in this article are important in designing rubber comp...

Elastomer composite blends and methods for producing them

Abstract: Elastomer composite blends are produced by novel wet/dry mixing methods and apparatus. In the wet mixing step or stage, fluid streams of particulate filler and elastomer latex are fed to the mixing zone of a coagulum reactor to form a mixture in semi-confined flow continuously from the mixing zone through a coagulum zone to a discharge end of the reactor. The particulate filler fluid is fed under high pressure to the mixing zone, such as to form a jet stream to entrain elastomer latex fluid sufficiently energetically to substantially completely coagulate the elastomer with the particulate filler prior to the discharge end. Highly efficient and effective elastomer coagulation is achieved without the need for a coagulation step involving exposure to acid or salt solution or the like. Elastomer composites are produced. Such elastomer composites may be cured or uncured, and combine material properties, such as choice of filler, elastomer, level of filler loading, and macro-dispersion, not previously achieved. The coagulum produced by such wet mixing step, with or without intermediate processing steps, is then mixed with additional elastomer in a dry mixing step or stage to form elastomer composite blends. The additional elastomer to the coagulum may be the same as or different from the elastomer(s) used in the wet mixing step.