Showing papers by "Florida State University published in 2019"

The Simons Observatory : Science goals and forecasts

Abstract: The Simons Observatory (SO) is a new cosmic microwave background experiment being built on Cerro Toco in Chile, due to begin observations in the early 2020s. We describe the scientific goals of the experiment, motivate the design, and forecast its performance. SO will measure the temperature and polarization anisotropy of the cosmic microwave background in six frequency bands centered at: 27, 39, 93, 145, 225 and 280 GHz. The initial configuration of SO will have three small-aperture 0.5-m telescopes and one large-aperture 6-m telescope, with a total of 60,000 cryogenic bolometers. Our key science goals are to characterize the primordial perturbations, measure the number of relativistic species and the mass of neutrinos, test for deviations from a cosmological constant, improve our understanding of galaxy evolution, and constrain the duration of reionization. The small aperture telescopes will target the largest angular scales observable from Chile, mapping ≈ 10% of the sky to a white noise level of 2 μK-arcmin in combined 93 and 145 GHz bands, to measure the primordial tensor-to-scalar ratio, r, at a target level of σ(r)=0.003. The large aperture telescope will map ≈ 40% of the sky at arcminute angular resolution to an expected white noise level of 6 μK-arcmin in combined 93 and 145 GHz bands, overlapping with the majority of the Large Synoptic Survey Telescope sky region and partially with the Dark Energy Spectroscopic Instrument. With up to an order of magnitude lower polarization noise than maps from the Planck satellite, the high-resolution sky maps will constrain cosmological parameters derived from the damping tail, gravitational lensing of the microwave background, the primordial bispectrum, and the thermal and kinematic Sunyaev-Zel'dovich effects, and will aid in delensing the large-angle polarization signal to measure the tensor-to-scalar ratio. The survey will also provide a legacy catalog of 16,000 galaxy clusters and more than 20,000 extragalactic sources.

Superconductivity at 250 K in lanthanum hydride under high pressures

Abstract: With the discovery1 of superconductivity at 203 kelvin in H3S, attention returned to conventional superconductors with properties that can be described by the Bardeen-Cooper-Schrieffer and the Migdal-Eliashberg theories. Although these theories predict the possibility of room-temperature superconductivity in metals that have certain favourable properties-such as lattice vibrations at high frequencies-they are not sufficient to guide the design or predict the properties of new superconducting materials. First-principles calculations based on density functional theory have enabled such predictions, and have suggested a new family of superconducting hydrides that possess a clathrate-like structure in which the host atom (calcium, yttrium, lanthanum) is at the centre of a cage formed by hydrogen atoms2-4. For LaH10 and YH10, the onset of superconductivity is predicted to occur at critical temperatures between 240 and 320 kelvin at megabar pressures3-6. Here we report superconductivity with a critical temperature of around 250 kelvin within the [Formula: see text] structure of LaH10 at a pressure of about 170 gigapascals. This is, to our knowledge, the highest critical temperature that has been confirmed so far in a superconducting material. Superconductivity was evidenced by the observation of zero resistance, an isotope effect, and a decrease in critical temperature under an external magnetic field, which suggested an upper critical magnetic field of about 136 tesla at zero temperature. The increase of around 50 kelvin compared with the previous highest critical temperature1 is an encouraging step towards the goal of achieving room-temperature superconductivity in the near future.

Age, period, and cohort trends in mood disorder indicators and suicide-related outcomes in a nationally representative dataset, 2005-2017.

Abstract: Drawing from the National Survey on Drug Use and Health (NSDUH; N = 611,880), a nationally representative survey of U.S. adolescents and adults, we assess age, period, and cohort trends in mood disorders and suicide-related outcomes since the mid-2000s. Rates of major depressive episode in the last year increased 52% 2005-2017 (from 8.7% to 13.2%) among adolescents aged 12 to 17 and 63% 2009-2017 (from 8.1% to 13.2%) among young adults 18-25. Serious psychological distress in the last month and suicide-related outcomes (suicidal ideation, plans, attempts, and deaths by suicide) in the last year also increased among young adults 18-25 from 2008-2017 (with a 71% increase in serious psychological distress), with less consistent and weaker increases among adults ages 26 and over. Hierarchical linear modeling analyses separating the effects of age, period, and birth cohort suggest the trends among adults are primarily due to cohort, with a steady rise in mood disorder and suicide-related outcomes between cohorts born from the early 1980s (Millennials) to the late 1990s (iGen). Cultural trends contributing to an increase in mood disorders and suicidal thoughts and behaviors since the mid-2000s, including the rise of electronic communication and digital media and declines in sleep duration, may have had a larger impact on younger people, creating a cohort effect. (PsycINFO Database Record (c) 2019 APA, all rights reserved).

Long-range enhancer-promoter contacts in gene expression control.

Abstract: Spatiotemporal gene expression programmes are orchestrated by transcriptional enhancers, which are key regulatory DNA elements that engage in physical contacts with their target-gene promoters, often bridging considerable genomic distances. Recent progress in genomics, genome editing and microscopy methodologies have enabled the genome-wide mapping of enhancer-promoter contacts and their functional dissection. In this Review, we discuss novel concepts on how enhancer-promoter interactions are established and maintained, how the 3D architecture of mammalian genomes both facilitates and constrains enhancer-promoter contacts, and the role they play in gene expression control during normal development and disease.

FCC-ee: The Lepton Collider: Future Circular Collider Conceptual Design Report Volume 2

Abstract: In response to the 2013 Update of the European Strategy for Particle Physics, the Future Circular Collider (FCC) study was launched, as an international collaboration hosted by CERN. This study covers a highest-luminosity high-energy lepton collider (FCC-ee) and an energy-frontier hadron collider (FCC-hh), which could, successively, be installed in the same 100 km tunnel. The scientific capabilities of the integrated FCC programme would serve the worldwide community throughout the 21st century. The FCC study also investigates an LHC energy upgrade, using FCC-hh technology. This document constitutes the second volume of the FCC Conceptual Design Report, devoted to the electron-positron collider FCC-ee. After summarizing the physics discovery opportunities, it presents the accelerator design, performance reach, a staged operation scenario, the underlying technologies, civil engineering, technical infrastructure, and an implementation plan. FCC-ee can be built with today’s technology. Most of the FCC-ee infrastructure could be reused for FCC-hh. Combining concepts from past and present lepton colliders and adding a few novel elements, the FCC-ee design promises outstandingly high luminosity. This will make the FCC-ee a unique precision instrument to study the heaviest known particles (Z, W and H bosons and the top quark), offering great direct and indirect sensitivity to new physics.

RMSEA, CFI, and TLI in structural equation modeling with ordered categorical data: The story they tell depends on the estimation methods

Abstract: In structural equation modeling, application of the root mean square error of approximation (RMSEA), comparative fit index (CFI), and Tucker–Lewis index (TLI) highly relies on the conventional cutoff values developed under normal-theory maximum likelihood (ML) with continuous data. For ordered categorical data, unweighted least squares (ULS) and diagonally weighted least squares (DWLS) based on polychoric correlation matrices have been recommended in previous studies. Although no clear suggestions exist regarding the application of these fit indices when analyzing ordered categorical variables, practitioners are still tempted to adopt the conventional cutoff rules. The purpose of our research was to answer the question: Given a population polychoric correlation matrix and a hypothesized model, if ML results in a specific RMSEA value (e.g., .08), what is the RMSEA value when ULS or DWLS is applied? CFI and TLI were investigated in the same fashion. Both simulated and empirical polychoric correlation matrices with various degrees of model misspecification were employed to address the above question. The results showed that DWLS and ULS lead to smaller RMSEA and larger CFI and TLI values than does ML for all manipulated conditions, regardless of whether or not the indices are scaled. Applying the conventional cutoffs to DWLS and ULS, therefore, has a pronounced tendency not to discover model–data misfit. Discussions regarding the use of RMSEA, CFI, and TLI for ordered categorical data are given.

Molecular spins for quantum computation.

Abstract: Spins in solids or in molecules possess discrete energy levels, and the associated quantum states can be tuned and coherently manipulated by means of external electromagnetic fields. Spins therefore provide one of the simplest platforms to encode a quantum bit (qubit), the elementary unit of future quantum computers. Performing any useful computation demands much more than realizing a robust qubit-one also needs a large number of qubits and a reliable manner with which to integrate them into a complex circuitry that can store and process information and implement quantum algorithms. This 'scalability' is arguably one of the challenges for which a chemistry-based bottom-up approach is best-suited. Molecules, being much more versatile than atoms, and yet microscopic, are the quantum objects with the highest capacity to form non-trivial ordered states at the nanoscale and to be replicated in large numbers using chemical tools.

Combined measurements of Higgs boson couplings in proton–proton collisions at √s=13Te

Abstract: Combined measurements of the production and decay rates of the Higgs boson, as well as its couplings to vector bosons and fermions, are presented. The analysis uses the LHC proton–proton collision data set recorded with the CMS detector in 2016 at $\sqrt{s}=13\,\text {Te}\text {V} $ , corresponding to an integrated luminosity of 35.9 ${\,\text {fb}^{-1}} $ . The combination is based on analyses targeting the five main Higgs boson production mechanisms (gluon fusion, vector boson fusion, and associated production with a $\mathrm {W}$ or $\mathrm {Z}$ boson, or a top quark-antiquark pair) and the following decay modes: $\mathrm {H} \rightarrow \gamma \gamma $ , $\mathrm {Z}\mathrm {Z}$ , $\mathrm {W}\mathrm {W}$ , $\mathrm {\tau }\mathrm {\tau }$ , $\mathrm {b} \mathrm {b} $ , and $\mathrm {\mu }\mathrm {\mu }$ . Searches for invisible Higgs boson decays are also considered. The best-fit ratio of the signal yield to the standard model expectation is measured to be $\mu =1.17\pm 0.10$ , assuming a Higgs boson mass of $125.09\,\text {Ge}\text {V} $ . Additional results are given for various assumptions on the scaling behavior of the production and decay modes, including generic parametrizations based on ratios of cross sections and branching fractions or couplings. The results are compatible with the standard model predictions in all parametrizations considered. In addition, constraints are placed on various two Higgs doublet models.

FCC-hh: The Hadron Collider

Abstract: Particle physics has arrived at an important moment of its history. The discovery of the Higgs boson, with a mass of 125 GeV, completes the matrix of particles and interactions that has constituted the “Standard Model” for several decades. This model is a consistent and predictive theory, which has so far proven successful at describing all phenomena accessible to collider experiments. However, several experimental facts do require the extension of the Standard Model and explanations are needed for observations such as the abundance of matter over antimatter, the striking evidence for dark matter and the non-zero neutrino masses. Theoretical issues such as the hierarchy problem, and, more in general, the dynamical origin of the Higgs mechanism, do likewise point to the existence of physics beyond the Standard Model. This report contains the description of a novel research infrastructure based on a highest-energy hadron collider with a centre-of-mass collision energy of 100 TeV and an integrated luminosity of at least a factor of 5 larger than the HL-LHC. It will extend the current energy frontier by almost an order of magnitude. The mass reach for direct discovery will reach several tens of TeV, and allow, for example, to produce new particles whose existence could be indirectly exposed by precision measurements during the earlier preceding e+e– collider phase. This collider will also precisely measure the Higgs self-coupling and thoroughly explore the dynamics of electroweak symmetry breaking at the TeV scale, to elucidate the nature of the electroweak phase transition. WIMPs as thermal dark matter candidates will be discovered, or ruled out. As a single project, this particle collider infrastructure will serve the world-wide physics community for about 25 years and, in combination with a lepton collider (see FCC conceptual design report volume 2), will provide a research tool until the end of the 21st century. Collision energies beyond 100 TeV can be considered when using high-temperature superconductors. The European Strategy for Particle Physics (ESPP) update 2013 stated “To stay at the forefront of particle physics, Europe needs to be in a position to propose an ambitious post-LHC accelerator project at CERN by the time of the next Strategy update”. The FCC study has implemented the ESPP recommendation by developing a long-term vision for an “accelerator project in a global context”. This document describes the detailed design and preparation of a construction project for a post-LHC circular energy frontier collider “in collaboration with national institutes, laboratories and universities worldwide”, and enhanced by a strong participation of industrial partners. Now, a coordinated preparation effort can be based on a core of an ever-growing consortium of already more than 135 institutes worldwide. The technology for constructing a high-energy circular hadron collider can be brought to the technology readiness level required for constructing within the coming ten years through a focused R&D programme. The FCC-hh concept comprises in the baseline scenario a power-saving, low-temperature superconducting magnet system based on an evolution of the Nb3Sn technology pioneered at the HL-LHC, an energy-efficient cryogenic refrigeration infrastructure based on a neon-helium (Nelium) light gas mixture, a high-reliability and low loss cryogen distribution infrastructure based on Invar, high-power distributed beam transfer using superconducting elements and local magnet energy recovery and re-use technologies that are already gradually introduced at other CERN accelerators. On a longer timescale, high-temperature superconductors can be developed together with industrial partners to achieve an even more energy efficient particle collider or to reach even higher collision energies.The re-use of the LHC and its injector chain, which also serve for a concurrently running physics programme, is an essential lever to come to an overall sustainable research infrastructure at the energy frontier. Strategic R&D for FCC-hh aims at minimising construction cost and energy consumption, while maximising the socio-economic impact. It will mitigate technology-related risks and ensure that industry can benefit from an acceptable utility. Concerning the implementation, a preparatory phase of about eight years is both necessary and adequate to establish the project governance and organisation structures, to build the international machine and experiment consortia, to develop a territorial implantation plan in agreement with the host-states’ requirements, to optimise the disposal of land and underground volumes, and to prepare the civil engineering project. Such a large-scale, international fundamental research infrastructure, tightly involving industrial partners and providing training at all education levels, will be a strong motor of economic and societal development in all participating nations. The FCC study has implemented a set of actions towards a coherent vision for the world-wide high-energy and particle physics community, providing a collaborative framework for topically complementary and geographically well-balanced contributions. This conceptual design report lays the foundation for a subsequent infrastructure preparatory and technical design phase.

FCC Physics Opportunities: Future Circular Collider Conceptual Design Report Volume 1

Abstract: We review the physics opportunities of the Future Circular Collider, covering its e+e-, pp, ep and heavy ion programmes. We describe the measurement capabilities of each FCC component, addressing the study of electroweak, Higgs and strong interactions, the top quark and flavour, as well as phenomena beyond the Standard Model. We highlight the synergy and complementarity of the different colliders, which will contribute to a uniquely coherent and ambitious research programme, providing an unmatchable combination of precision and sensitivity to new physics.

45.5-tesla direct-current magnetic field generated with a high-temperature superconducting magnet

Abstract: Strong magnetic fields are required in many fields, such as medicine (magnetic resonance imaging), pharmacy (nuclear magnetic resonance), particle accelerators (such as the Large Hadron Collider) and fusion devices (for example, the International Thermonuclear Experimental Reactor, ITER), as well as for other diverse scientific and industrial uses. For almost two decades, 45 tesla has been the highest achievable direct-current (d.c.) magnetic field; however, such a field requires the use of a 31-megawatt, 33.6-tesla resistive magnet inside 11.4-tesla low-temperature superconductor coils1, and such high-power resistive magnets are available in only a few facilities worldwide2. By contrast, superconducting magnets are widespread owing to their low power requirements. Here we report a high-temperature superconductor coil that generates a magnetic field of 14.4 tesla inside a 31.1-tesla resistive background magnet to obtain a d.c. magnetic field of 45.5 tesla—the highest field achieved so far, to our knowledge. The magnet uses a conductor tape coated with REBCO (REBa2Cu3Ox, where RE = Y, Gd) on a 30-micrometre-thick substrate3, making the coil highly compact and capable of operating at the very high winding current density of 1,260 amperes per square millimetre. Operation at such a current density is possible only because the magnet is wound without insulation4, which allows rapid and safe quenching from the superconducting to the normal state5–10. The 45.5-tesla test magnet validates predictions11 for high-field copper oxide superconductor magnets by achieving a field twice as high as those generated by low-temperature superconducting magnets. A copper oxide high-temperature superconductor magnet generates a direct-current magnetic field of 45.5 tesla—the highest value reported so far—using a design that enables operation at high current densities.

Technological disruptions in services: lessons from tourism and hospitality

Abstract: Technological disruptions such as the Internet of Things and autonomous devices, enhanced analytical capabilities (artificial intelligence) and rich media (virtual and augmented reality) are creating smart environments that are transforming industry structures, processes and practices. The purpose of this paper is to explore critical technological advancements using a value co-creation lens to provide insights into service innovations that impact ecosystems. The paper provides examples from tourism and hospitality industries as an information dependent service management context.,The research synthesizes prevailing theories of co-creation, service ecosystems, networks and technology disruption with emerging technological developments.,Findings highlight the need for research into service innovations in the tourism and hospitality sector at both macro-market and micro-firm levels, emanating from the rapid and radical nature of technological advancements. Specifically, the paper identifies three areas of likely future disruption in service experiences that may benefit from immediate attention: extra-sensory experiences, hyper-personalized experiences and beyond-automation experiences.,Tourism and hospitality services prevail under varying levels of infrastructure, organization and cultural constraints. This paper provides an overview of potential disruptions and developments and does not delve into individual destination types and settings. This will require future work that conceptualizes and examines how stakeholders may adapt within specific contexts.,Technological disruptions impact all facets of life. A comprehensive picture of developments here provides policymakers with nuanced perspectives to better prepare for impending change.,Guest experiences in tourism and hospitality by definition take place in hostile environments that are outside the safety and familiarity of one’s own surroundings. The emergence of smart environments will redefine how customers navigate their experiences. At a conceptual level, this requires a complete rethink of how stakeholders should leverage technologies, engage and reengineer services to remain competitive. The paper illustrates how technology disrupts industry structures and stimulates value co-creation at the micro and macro-societal level.

An ultrafast symmetry switch in a Weyl semimetal.

Abstract: Topological quantum materials exhibit fascinating properties1–3, with important applications for dissipationless electronics and fault-tolerant quantum computers4,5. Manipulating the topological invariants in these materials would allow the development of topological switching applications analogous to switching of transistors6. Lattice strain provides the most natural means of tuning these topological invariants because it directly modifies the electron–ion interactions and potentially alters the underlying crystalline symmetry on which the topological properties depend7–9. However, conventional means of applying strain through heteroepitaxial lattice mismatch10 and dislocations11 are not extendable to controllable time-varying protocols, which are required in transistors. Integration into a functional device requires the ability to go beyond the robust, topologically protected properties of materials and to manipulate the topology at high speeds. Here we use crystallographic measurements by relativistic electron diffraction to demonstrate that terahertz light pulses can be used to induce terahertz-frequency interlayer shear strain with large strain amplitude in the Weyl semimetal WTe2, leading to a topologically distinct metastable phase. Separate nonlinear optical measurements indicate that this transition is associated with a symmetry change to a centrosymmetric, topologically trivial phase. We further show that such shear strain provides an ultrafast, energy-efficient way of inducing robust, well separated Weyl points or of annihilating all Weyl points of opposite chirality. This work demonstrates possibilities for ultrafast manipulation of the topological properties of solids and for the development of a topological switch operating at terahertz frequencies. Terahertz light pulses induce transitions between a topological and a trivial phase in the Weyl semimetal WTe2 through an interlayer shear strain.

Special Article: 2018 American College of Rheumatology/National Psoriasis Foundation Guideline for the Treatment of Psoriatic Arthritis.

Abstract: Objective To develop an evidence-based guideline for the pharmacologic and nonpharmacologic treatment of psoriatic arthritis (PsA), as a collaboration between the American College of Rheumatology (ACR) and the National Psoriasis Foundation (NPF). Methods We identified critical outcomes in PsA and clinically relevant PICO (population/intervention/comparator/outcomes) questions. A Literature Review Team performed a systematic literature review to summarize evidence supporting the benefits and harms of available pharmacologic and nonpharmacologic therapies for PsA. GRADE (Grading of Recommendations Assessment, Development and Evaluation) methodology was used to rate the quality of the evidence. A voting panel, including rheumatologists, dermatologists, other health professionals, and patients, achieved consensus on the direction and the strength of the recommendations. Results The guideline covers the management of active PsA in patients who are treatment-naive and those who continue to have active PsA despite treatment, and addresses the use of oral small molecules, tumor necrosis factor inhibitors, interleukin-12/23 inhibitors (IL-12/23i), IL-17 inhibitors, CTLA4-Ig (abatacept), and a JAK inhibitor (tofacitinib). We also developed recommendations for psoriatic spondylitis, predominant enthesitis, and treatment in the presence of concomitant inflammatory bowel disease, diabetes, or serious infections. We formulated recommendations for a treat-to-target strategy, vaccinations, and nonpharmacologic therapies. Six percent of the recommendations were strong and 94% conditional, indicating the importance of active discussion between the health care provider and the patient to choose the optimal treatment. Conclusion The 2018 ACR/NPF PsA guideline serves as a tool for health care providers and patients in the selection of appropriate therapy in common clinical scenarios. Best treatment decisions consider each individual patient situation. The guideline is not meant to be proscriptive and should not be used to limit treatment options for patients with PsA.

Recommendations for reporting ion mobility Mass Spectrometry measurements

Abstract: Here we present a guide to ion mobility mass spectrometry experiments, which covers both linear and nonlinear methods: what is measured, how the measurements are done, and how to report the results, including the uncertainties of mobility and collision cross section values. The guide aims to clarify some possibly confusing concepts, and the reporting recommendations should help researchers, authors and reviewers to contribute comprehensive reports, so that the ion mobility data can be reused more confidently. Starting from the concept of the definition of the measurand, we emphasize that (i) mobility values (K0) depend intrinsically on ion structure, the nature of the bath gas, temperature, and E/N; (ii) ion mobility does not measure molecular surfaces directly, but collision cross section (CCS) values are derived from mobility values using a physical model; (iii) methods relying on calibration are empirical (and thus may provide method‐dependent results) only if the gas nature, temperature or E/N cannot match those of the primary method. Our analysis highlights the urgency of a community effort toward establishing primary standards and reference materials for ion mobility, and provides recommendations to do so.

2018 American College of Rheumatology/National Psoriasis Foundation Guideline for the Treatment of Psoriatic Arthritis

Abstract: Objective:To develop an evidence-based guideline for the pharmacologic and nonpharmacologic treatment of psoriatic arthritis (PsA), as a collaboration between the American College of Rheumatology (...

Strong coupling phases of partially filled twisted bilayer graphene narrow bands

Abstract: We identify states favored by Coulomb interactions projected onto the Wannier basis of the four narrow bands of the "magic angle" twisted bilayer graphene. At the filling of 2 electrons/holes per moire unit cell, such interactions favor an insulating SU(4) ferromagnet. The kinetic terms select the ground state in which the two valleys with opposite spins are equally mixed, with a vanishing magnetic moment per particle. We also find extended excited states, the gap to which decreases in the magnetic field. An insulating stripe ferromagnetic phase is favored at 1 electron/hole per unit cell.

At Least Bias Is Bipartisan: A Meta-Analytic Comparison of Partisan Bias in Liberals and Conservatives.

Abstract: Both liberals and conservatives accuse their political opponents of partisan bias, but is there empirical evidence that one side of the political aisle is indeed more biased than the other? To addr...

Low dimensional metal halide perovskites and hybrids

Abstract: Organic-inorganic metal halide hybrids are an important class of crystalline materials with exceptional structural and property tunability. Recently metal halide perovskites with ABX3 structure have been extensively investigated as new generation semiconductors for various optoelectronic devices, including photovoltaic cells, light emitting diodes, photodetectors, and lasers, for their exceptional optical and electronic properties. By controlling the morphological dimensionality, low dimensional metal halide perovskites, including 2D perovskite nanoplatelets, 1D perovskite nanowires, and 0D perovskite quantum dots, have been developed to exhibit distinct properties from their bulk counterparts, due to quantum size effects. Besides ABX3 perovskites, organic-inorganic metal halide hybrids, containing the same fundamental building block of metal halide octahedra (BX6), can also be assembled to possess other types of crystallographic structures. Using appropriate organic and inorganic components, low dimensional organic-inorganic metal halide hybrids with 2D, quasi-2D, corrugated-2D, 1D, and 0D structures at the molecular level have been developed and studied. Due to the strong quantum confinement and site isolation, these low dimensional metal halide hybrids at the molecular level exhibit remarkable and unique properties that are significantly different from those of ABX3 perovskites. In light of the rapid development of low dimensional metal halide perovskites and hybrids, it is indeed timely to review the recent progress in these areas. Also, there is a need to clarify the difference between morphological low dimensional metal halide perovskites and molecular level low dimensional metal halide hybrids, as currently the terminologies of low dimensional perovskites are not appropriately used in many cases. In this review article, we discuss the synthesis, characterization, application, and computational studies of low dimensional metal halide perovskites and hybrids.

Three-dimensional quantum Hall effect and metal–insulator transition in ZrTe 5

Abstract: The discovery of the quantum Hall effect (QHE)1,2 in two-dimensional electronic systems has given topology a central role in condensed matter physics. Although the possibility of generalizing the QHE to three-dimensional (3D) electronic systems3,4 was proposed decades ago, it has not been demonstrated experimentally. Here we report the experimental realization of the 3D QHE in bulk zirconium pentatelluride (ZrTe5) crystals. We perform low-temperature electric-transport measurements on bulk ZrTe5 crystals under a magnetic field and achieve the extreme quantum limit, where only the lowest Landau level is occupied, at relatively low magnetic fields. In this regime, we observe a dissipationless longitudinal resistivity close to zero, accompanied by a well-developed Hall resistivity plateau proportional to half of the Fermi wavelength along the field direction. This response is the signature of the 3D QHE and strongly suggests a Fermi surface instability driven by enhanced interaction effects in the extreme quantum limit. By further increasing the magnetic field, both the longitudinal and Hall resistivity increase considerably and display a metal-insulator transition, which represents another magnetic-field-driven quantum phase transition. Our findings provide experimental evidence of the 3D QHE and a promising platform for further exploration of exotic quantum phases and transitions in 3D systems.

A Hierarchical Taxonomy of Psychopathology Can Transform Mental Health Research

Abstract: For more than a century, research on psychopathology has focused on categorical diagnoses. Although this work has produced major discoveries, growing evidence points to the superiority of a dimensional approach to the science of mental illness. Here we outline one such dimensional system-the Hierarchical Taxonomy of Psychopathology (HiTOP)-that is based on empirical patterns of co-occurrence among psychological symptoms. We highlight key ways in which this framework can advance mental-health research, and we provide some heuristics for using HiTOP to test theories of psychopathology. We then review emerging evidence that supports the value of a hierarchical, dimensional model of mental illness across diverse research areas in psychological science. These new data suggest that the HiTOP system has the potential to accelerate and improve research on mental-health problems as well as efforts to more effectively assess, prevent, and treat mental illness.

Translating Marine Animal Tracking Data into Conservation Policy and Management

Abstract: There have been efforts around the globe to track individuals of many marine species and assess their movements and distribution, with the putative goal of supporting their conservation and management. Determining whether, and how, tracking data have been successfully applied to address real-world conservation issues is, however, difficult. Here, we compile a broad range of case studies from diverse marine taxa to show how tracking data have helped inform conservation policy and management, including reductions in fisheries bycatch and vessel strikes, and the design and administration of marine protected areas and important habitats. Using these examples, we highlight pathways through which the past and future investment in collecting animal tracking data might be better used to achieve tangible conservation benefits.

Super-resolution reconstruction of turbulent flows with machine learning

Abstract: We use machine learning to perform super-resolution analysis of grossly under-resolved turbulent flow field data to reconstruct the high-resolution flow field. Two machine learning models are developed, namely, the convolutional neural network (CNN) and the hybrid downsampled skip-connection/multi-scale (DSC/MS) models. These machine learning models are applied to a two-dimensional cylinder wake as a preliminary test and show remarkable ability to reconstruct laminar flow from low-resolution flow field data. We further assess the performance of these models for two-dimensional homogeneous turbulence. The CNN and DSC/MS models are found to reconstruct turbulent flows from extremely coarse flow field images with remarkable accuracy. For the turbulent flow problem, the machine-leaning-based super-resolution analysis can greatly enhance the spatial resolution with as little as 50 training snapshot data, holding great potential to reveal subgrid-scale physics of complex turbulent flows. With the growing availability of flow field data from high-fidelity simulations and experiments, the present approach motivates the development of effective super-resolution models for a variety of fluid flows.

High-performance all-solid-state batteries enabled by salt bonding to perovskite in poly(ethylene oxide).

Abstract: Flexible and low-cost poly(ethylene oxide) (PEO)-based electrolytes are promising for all-solid-state Li-metal batteries because of their compatibility with a metallic lithium anode. However, the low room-temperature Li-ion conductivity of PEO solid electrolytes and severe lithium-dendrite growth limit their application in high-energy Li-metal batteries. Here we prepared a PEO/perovskite Li3/8Sr7/16Ta3/4Zr1/4O3 composite electrolyte with a Li-ion conductivity of 5.4 × 10−5 and 3.5 × 10−4 S cm−1 at 25 and 45 °C, respectively; the strong interaction between the F− of TFSI− (bis-trifluoromethanesulfonimide) and the surface Ta5+ of the perovskite improves the Li-ion transport at the PEO/perovskite interface. A symmetric Li/composite electrolyte/Li cell shows an excellent cyclability at a high current density up to 0.6 mA cm−2. A solid electrolyte interphase layer formed in situ between the metallic lithium anode and the composite electrolyte suppresses lithium-dendrite formation and growth. All-solid-state Li|LiFePO4 and high-voltage Li|LiNi0.8Mn0.1Co0.1O2 batteries with the composite electrolyte have an impressive performance with high Coulombic efficiencies, small overpotentials, and good cycling stability.