Ghulam Ishaq Khan Institute of Engineering Sciences and Technology

About: Ghulam Ishaq Khan Institute of Engineering Sciences and Technology is a education organization based out in Topi, Pakistan. It is known for research contribution in the topics: Thin film & Quantum efficiency. The organization has 618 authors who have published 940 publications receiving 10674 citations.

Study of the Effect of Newly Calculated Phase Space Factor on β-Decay Half-Lives

Abstract: We present results for - decay half-lives based on a new recipe for calculation of phase space factors recently introduced. Our study includes - shell and heavier nuclei of experimental and astrophysical interests. The investigation of the kinematics of some - decay half-lives is presented, and new phase space factor values are compared with those obtained with previous theoretical approximations. Accurate calculation of nuclear matrix elements is a prerequisite for reliable computation of - decay half-lives and is not the subject of this paper. This paper explores if improvements in calculating the - decay half-lives can be obtained when using a given set of nuclear matrix elements and employing the new values of the phase space factors. Although the largest uncertainty in half-lives computations come from the nuclear matrix elements, introduction of the new values of the phase space factors may improve the comparison with experiment. The new half-lives are systematically larger than previous calculations and may have interesting consequences for calculation of stellar rates.

Multiphysics Impact Analysis of Carbon Fiber Reinforced Polymer (CFRP) Shell

Abstract: With increasing popularity of Carbon Fiber Reinforced Polymer (CFRP) over time, the need for research in the field has increased dramatically. Many industries, i.e. aeronautical, automotive, and marine are opting to install carbon fiber in their structures to account for harsh environments like cold temperatures applications, but the research on the temperature exposure behavior of the materials are limited. This study aims to investigate the impact resistance of CFRP samples using the air gun tests. Two different shaped pellets (Diabolo and Storm pellets) were used in this work. The pellets speeds were calculated using a high-speed camera. The tests were performed in the room temperature (22°C) as well as in the cold room where the test pieces were exposed to about -28°C for seven days. The experimental studies were performed and compared against finite element simulations using ANSYS®. The studies also included layering of the CFRP samples to find the limiting thickness of pellets penetration. It was concluded that the thickness of 0.79mm and below of CFRP, cannot resist the impact of pellets. The visual inspection of failure revealed that the CFRP has gone through a brittle failure. However, temperature was found to have no significant impact on the results as similar behavior of CFRP was observed in both room conditions (22°C) and cold temperatures (-28°C). Introduction In the last decades, a growing interest has been dedicated in the use of composite materials for structural applications. CFRP composites are gaining a special attention to replace traditional materials in several fields although it is well known that these systems are highly susceptible to internal damage caused by transverse loads even under low-velocity ones [1,2]. In general, CFRP composites can be damaged on the surface and also beneath the surface by relatively light impacts causing invisible impact damage [3]. Therefore, this study has been carried out both to highlight effects of variables linked to geometrical parameters of composite sheets, impactor, and operative conditions. Therefore, this study has been carried out both to highlight effects of variables linked to geometrical parameters of composite sheets, impactor, and operative conditions. Operative conditions affect the material properties as reported in [4-6]. Experimental Setup a. Test Samples Test samples used in this study were from the DragonPlate®, manufactured by Allred and Associates Inc., Elbridge, New York [7]. The CFRP samples used were EconomyPlateTM Solid Explosion Shock Waves and High Strain Rate Phenomena Materials Research Forum LLC Materials Research Proceedings 13 (2019) 115-120 https://doi.org/10.21741/9781644900338-20 116 Carbon Fiber Sheet ~ 1/32" x 12" x 12" (0.79375mm x 304.8mm x 304.8mm) [8]. EconomyPlateTM sheets comprised of orthotropic (non-quasi-isotropic) at 0°/90° orientation laminates [9] (Figure 1.) utilizing a twill weave [10] (Figure 2.), while maintaining a symmetrical and balanced laminate. EconomyPlateTM composed entirely of a tough and rigid carbon reinforced epoxy matrix, with textured finish on both sides. Samples were cut into smaller pieces for test purposes (Figure 3.). Figure 1-0°/90° orientation laminate Figure 2-Carbon fiber twill weave Figure 3-CFRP test samples b. Impact Tests To perform the impact tests, a shooting box was built, as shown in Figure 4a. The shooting box was designed such that it collects the pallets once they pass through the samples. The box consists of an opening-closing system with locking screws and wingnuts, so test pieces could be fastened for testing (Figure 4b), and removed and replaced with new test pieces effectively. Diabolo and storm pellets (Figures 5 and 6.) were shot on to the CFRP test samples. The material of both pellets was lead and they were of 4.5mm caliber, weighing about 0.5g each. The test was performed in room temperature, on tempered test pieces at about 22°C and in the cold room on test pieces exposed to about -28 ̊C for 7 days. Explosion Shock Waves and High Strain Rate Phenomena Materials Research Forum LLC Materials Research Proceedings 13 (2019) 115-120 https://doi.org/10.21741/9781644900338-20 117 (a) Shooting box (b) Fastened test piece Figure 4 – The opening-closing system of the shooting box Figure 5-Diabolo pellets Figure 6-Storm pellets A speed tests were carried out using a high-speed camera (Figure 7.). The test showed the pellets speed of about 160m/s. Figure 7-Speed test of Diabolo pellet (pellet speed ~ 160m/s) Explosion Shock Waves and High Strain Rate Phenomena Materials Research Forum LLC Materials Research Proceedings 13 (2019) 115-120 https://doi.org/10.21741/9781644900338-20 118 Experimental Results Impact tests revealed that diabolo and storm pellets at 160m/s pass through the single layer (~0.79 mm) of CFRP (Figure 8). Visual inspection showed that the CFRP test samples were ruptured (brittle failure) and the failure was in the close vicinity of the impact. Ruptured holes were more visible when Storm pellets were used, nonetheless, the failure areas were the same. (a) Diabolo pellets (b) Storm pellets Figure 8-Visual inspection of the impact Tests were repeated by tightly joining the layers of CFRP tests samples (0.79mm, 1.59mm, and 2.38mm). Pellets passed through 0.79mm and 1.59mm thick CFRP test samples, however, deflected for 2.38mm layer. Same results were observed when tests were conducted at room temperature conditions (22°C) and cold conditions (-28°C). Simulations Setup The simulations were performed in ANSYS® Explicit Dynamic [11]. Mesh sensitivity analysis was performed to ensure the accuracy of results. The model parameters are given in Table 1. Table 1: Simulation model parameters (ANSYS® Explicit Dynamic) Physics preference Explicit Relevance 70 Relevance Center Fine Span Angle Center Fine Nodes (optimized) 9193 Elements (optimized) 13786 Simulations Results ANSYS® Explicit Dynamic simulations revealed similar behavior as seen in experiments. For example, 0.79mm CFRP went through rupture failure as shown in Figure 9. Tsai-Wu failure model was used in the simulations [12]. Explosion Shock Waves and High Strain Rate Phenomena Materials Research Forum LLC Materials Research Proceedings 13 (2019) 115-120 https://doi.org/10.21741/9781644900338-20 119 Side view Sample front view Sample back view Figure 9ANSYS® Explicit Dynamic simulations Comparison of Experiments and Simulations Table 2 summarizes the results from experiments and simulations. As shown, Experiments Simulations CFRP thickness = 0.79mm @ 25°C to -28°C Failed Failed CFRP thickness = 1.59mm @ 25°C to -28°C Failed Failed CFRP thickness = 1.63mm @ 25°C to -28°C (not tested) Safe CFRP thickness = 2.38mm @ 25°C to -28°C Safe Safe Conclusions and Limitations Following conclusion can be drawn from the study: 1. It can be concluded that pellet and storm pellets at 160 m/s can damage/pass through the 1.59mm and below thickness of CFRP. 2. Good agreement was found between the experiments and simulations. It confirms that Multiphysics methodology such as Explicit Dynamic simulations may be used for the design of CFRP structures undergoing impact loading. 3. It was found that CFRP material properties did not change noticeably in cold temperatures. Following limitations apply to the given study: 1. Commercially available CFRP samples (DragonPlate®) were used in this study. 2. Commercially available Multiphysics software ANSYS® was used for the simulations. 3. Samples were visually inspected and not for micro-fractures/micro-delamination. Acknowledgement Thanks to Prof. Young Kwon from Naval Postgraduate School, Monterey, California, USA for providing the test samples. References [1] Khawaja, Hassan Abbas; Moatamedi, Mojtaba. Multiphysics Investigation of Composite Shell Structures Subjected to Water Shock Wave Impact in Petroleum Industry. Materials Science Forum 2013. doi: https://doi.org/10.4028/www.scientific.net/MSF.767.60. Explosion Shock Waves and High Strain Rate Phenomena Materials Research Forum LLC Materials Research Proceedings 13 (2019) 115-120 https://doi.org/10.21741/9781644900338-20 120 [2] Khawaja, Hassan Abbas; Messahel, Ramzi; Souli, Mhmed; Al-Bahkali, Essam; Moatamedi, Mojtaba. Fluid solid interaction simulation of CFRP shell structure. Mathematics in Engineering, Science and Aerospace (MESA) 2017, 8(3), p. 311-324. Link: http://nonlinearstudies.com/index.php/mesa/article/view/1532 [3] Khawaja, Hassan Abbas; Bertelsen, Tommy; Andreassen, Roar; Moatamedi, Mojtaba. Study of CRFP Shell Structures under Dynamic Loading in Shock Tube Setup. Journal of Structures 2014, doi: http://dx.doi.org/10.1155/2014/487809. [4] Stange, Even; Andleeb, Zahra; Khawaja, Hassan; Moatamedi, Mojtaba. Multiphysics Study of Tensile Testing using Infrared thermography. The International Journal of Multiphysics 2019; 13(2), p. 191-202. doi: http://dx.doi.org/10.21152/1750-9548.13.2.191 [5] Myrli, Odd Einar; Khawaja, Hassan. Fluid-Structure Interaction (FSI) Modelling of Aquaculture Net Cage. The International Journal of Multiphysics 2019; 13(1). p. 97-111. doi: http://dx.doi.org/10.21152/1750-9548.13.1.97 [6] Ahmad, Tanveer; Khawaja, Hassan. Review of Low-Temperature Crack (LTC) Developments in Asphalt Pavements. The International Journal of Multiphysics 2018; 12(2). p. 169-187. doi: http://dx.doi.org/10.21152/1750-9548.12.2.169 [7] Allred and Associates Inc Company. [cited 03.03.2019]; Available from: http://dragonplate.com/sections/company.asp. [8] Allred and Associates Inc Product. [cited 03.03.2019]; Available from: https://dragonplate.com/economyplate-solid-carbon-fiber-sheet-1_32-x-12-x-12. [9] Allred and Associates Inc – Non-quasi-isotropic. [cited 03.03.2019]; Available from: https://dragonplate.com/quasi-isotropic-carbon-fiber-sheets. [10] Allred and Associates Inc -Twill weave. [cited 03.03.2019]; Available from: https://dragonplate.com/what-is-carbon-fiber. [11] ANSYS® Explicit Dynamic [cited 03.03.201

A Novel Color Image Retrieval System Based On Dual Tree Complex Wavelet Transform and Support Vector Machines

Abstract: This paper presents a novel color image retrieval system (SVMBIR) based on dual tree complex wavelet transform (CWT) and support vector machines (SVM). We have shown that how one can improve the performance of image retrieval systems by assuming two attributes. Firstly, images that user needs through query image are similar to a group of images with same conception. Secondly, there exists non-linear relationship between feature vectors of different images and can be exploited very efficiently with the use of support vector machines. At first level, for low level feature extraction we have used dual tree complex wavelet transform because recently it is proven that CWT can be used for efficient color feature extraction just like texture feature extraction. At second level to extract semantic concepts, we grouped images of typical classes with the use of one against all support vector machines. We have also shown how one can use a correlation based distance metric for comparison of SVM distance vectors. The experimental results show that the proposed approach has superior retrieval performance over the existing linear feature combining techniques.

High Radiative Recombination Rate of AlGaN-Based Deep Ultraviolet Light-Emitting Diodes with AlInGaN/AlInN/AlInGaN Tunnel Electron Blocking Layer

Abstract: In this study, an aluminum indium gallium nitride (AlInGaN)/aluminum indium nitride (AlInN)/aluminum indium gallium nitride (AlInGaN) tunnel electron blocking layer (EBL) is introduced instead of traditional EBL in aluminum gallium nitride (AlGaN)-based deep UV light-emitting diodes (DUV LEDs). The simulation results reveal that the internal quantum efficiency (IQE) and radiative recombination rate are impressively improved in the proposed DUV LED as compared to the conventional LED. This significant improvement is assigned to the uniform recombination of carriers in the active zone due to the reduction of lattice mismatching, which is the main cause of reducing the induced piezoelectric polarization field. Additionally, the tunnel EBL in our proposed structure also assists the hole transport into the active zone. As a result, not only is IQE improved, but also the efficiency droop is reduced significantly in our proposed device. This is attributed to the enhanced recombination of electron-hole pairs in the active region.