Institution
Indian Institute of Technology Indore
Education•Indore, Madhya Pradesh, India•
About: Indian Institute of Technology Indore is a education organization based out in Indore, Madhya Pradesh, India. It is known for research contribution in the topics: Fading & Support vector machine. The organization has 1606 authors who have published 4803 publications receiving 66500 citations.
Topics: Fading, Support vector machine, Raman spectroscopy, Band gap, Thin film
Papers published on a yearly basis
Papers
More filters
••
TL;DR: In this paper, the photovoltaic properties of carbazole-based diketopyrrolopyrroles with tetracyanobutadiene acceptor units were investigated.
Abstract: Herein, we investigated the photovoltaic properties of carbazole-based diketopyrrolopyrroles with tetracyanobutadiene acceptor units as highly efficient non-fullerene acceptors together with a D–A conjugated polymer, P, as a donor for polymer solar cells. After optimization, i.e. donor to acceptor weight ratio and solvent vapour annealing, the polymer solar cells exhibited power conversion efficiencies of up to 4.86% and 7.19% for DPP7 and DPP8 as acceptors, respectively. These results indicate that slight changes in the chemical structure of the small acceptor molecule significantly increase the efficiency of the device. The design and synthesis of these non-fullerene acceptors with broader absorption spectra extended towards the near infrared region may be key for the further development of high-performance and cost-effective solution-processed organic solar cells.
51 citations
••
Shreyasi Acharya1, Dagmar Adamová2, Jonatan Adolfsson3, Madan M. Aggarwal4 +1031 more•Institutions (100)
TL;DR: In this paper, the J/ψ mesons are reconstructed at midrapidity (|y|<0.9) in the dielectron decay channel and at forward rapidity (2.5
Abstract: We report a precise measurement of the J/ψ elliptic flow in Pb-Pb collisions at sNN=5.02 TeV with the ALICE detector at the LHC. The J/ψ mesons are reconstructed at midrapidity (|y|<0.9) in the dielectron decay channel and at forward rapidity (2.5
51 citations
••
TL;DR: It is found that the FBG sensor can be successfully embedded into PLA material without sacrificing its sensing performance and the change of infill density has no influence on both peak and residual wavelength change of FBG sensors during and after the printing process.
Abstract: In this paper, a fiber Bragg grating (FBG) pressure sensor was designed and fabricated using 3D printing method for the measurement of vertical pressure. The raw material used for the fabrication of this new pressure sensor was Polylactic Acid (PLA). The effectiveness of embedding FBG sensors inside printed PLA material was first examined taking into account different infill densities. It is found that the FBG sensor can be successfully embedded into PLA material without sacrificing its sensing performance. The change of infill density has no influence on both peak and residual wavelength change of FBG sensors during and after the printing process. All FBG sensors printed inside PLA prototype with different infill density values exhibit almost the same peak and residual wavelength rise values in the printing process. In addition, the higher the density value, the longer the time required to finish printing process. A simple FBG pressure sensor was designed and fabricated according to the successful experience of embedding FBG sensors into printed PLA. Measurement performance of this FBG pressure sensor was examined in laboratory cyclic loading tests. Calibration tests indicate that the maximum measured vertical pressure of this new pressure sensor was 2000 kPa with a measurement sensitivity of 13.22 kPa/pm.
51 citations
••
TL;DR: In this paper, the authors report the natural occurrence of fluorescent carbon dots in honey, a sweet nutrient made by bees foraging nectars from flowers and traditionally known for its medicinal values.
51 citations
••
TL;DR: In this article, an electrochromic device capable of three-level color switching was proposed by exploiting different color switching properties of Ethyl viologen (EV) and Poly (3-hexylthiophene) (P3HT) to make them switch in congruence with each other.
50 citations
Authors
Showing all 1738 results
Name | H-index | Papers | Citations |
---|---|---|---|
Raghunath Sahoo | 106 | 556 | 37588 |
Biswajeet Pradhan | 98 | 735 | 32900 |
A. Kumar | 96 | 505 | 33973 |
Franco Meddi | 84 | 476 | 24084 |
Manish Sharma | 82 | 1407 | 33361 |
Anindya Roy | 59 | 301 | 14306 |
Krishna R. Reddy | 58 | 400 | 11076 |
Sudipan De | 54 | 99 | 10774 |
Sudip Chakraborty | 51 | 343 | 9319 |
Shaikh M. Mobin | 51 | 515 | 11467 |
Ashok Kumar | 50 | 405 | 10001 |
Ankhi Roy | 49 | 259 | 8634 |
Aditya Nath Mishra | 49 | 139 | 7607 |
Ram Bilas Pachori | 48 | 182 | 8140 |
Pragati Sahoo | 47 | 133 | 6535 |