Institution
Langley Research Center
Facility•Hampton, Virginia, United States•
About: Langley Research Center is a facility organization based out in Hampton, Virginia, United States. It is known for research contribution in the topics: Mach number & Wind tunnel. The organization has 15945 authors who have published 37602 publications receiving 821623 citations. The organization is also known as: NASA Langley & NASA Langley Research Center.
Topics: Mach number, Wind tunnel, Aerodynamics, Boundary layer, Supersonic speed
Papers published on a yearly basis
Papers
More filters
••
TL;DR: In this article, the authors presented the stress-intensity factors for shallow and deep semi-elliptical surface cracks in plates subjected to tension and verified the accuracy of the three-dimensional finite-element models employed.
591 citations
••
TL;DR: It is shown that, although the lack of comparative data established on reference test cases prevents an accurate assessment, there have been significant improvements in approximation concepts since the introduction of approximation concepts in the mid-seventies.
Abstract: This paper reviews the basic approximation concepts used in structural optimization. It also discusses some of the most recent developments in that area since the introduction of approximation concepts in the mid-seventies. The paper distinguishes between local, medium-range and global approximations; it covers function approximations and problem approximations. It shows that, although the lack of comparative data established on reference test cases prevents an accurate assessment, there have been significant improvements. The largest number of developments have been in the areas of local function approximations and use of intermediate variable and response quantities. It appears also that some new methodologies emerge which could greatly benefit from the introduction of new computer architectures.
581 citations
••
TL;DR: In this paper, the use of a genetic algorithm to optimize the stacking sequence of a composite laminate for buckling load maximization is studied, and the advantage of the genetic algorithm in producing several near-optimal designs is discussed.
Abstract: The use of a genetic algorithm to optimize the stacking sequence of a composite laminate for buckling load maximization is studied. Various genetic parameters including the population size, the probability of mutation, and the probability of crossover are optimized by numerical experiments. A new genetic operator - permutation - is proposed and shown to be effective in reducing the cost of the genetic search. Results are obtained for a graphite-epoxy plate, first when only the buckling load is considered, and then when constraints on ply contiguity and strain failure are added. The influence on the genetic search of the penalty parameter enforcing the contiguity constraint is studied. The advantage of the genetic algorithm in producing several near-optimal designs is discussed.
576 citations
••
TL;DR: In this paper, a mixed-mode delamination test procedure was developed combining double cantilever beam (DCB) mode I loading and end-notch fixture (ENF) mode II loading on a split unidirectional laminate.
Abstract: A mixed-mode delamination test procedure was developed combining double cantilever beam (DCB) mode I loading and end-notch fixture (ENF) mode II loading on a split unidirectional laminate. By loading with a lever, a single applied load simultaneously produces mode I and mode II bending loads on the specimen. This mixed-mode bending (MMB) test was analyzed using both finite-element procedures and beam theory to calculate the mode I and mode II components of strain-energy release rate GI and GII, respectively. A wide range of G(sub)I/G(sub)II ratios can be produced by varying the load position on the lever. As the delamination extended, the G(sub)I/G(sub)II ratios varied by less than 5 percent. Beam theory equations agreed closely with the finite-element results and provide a basis for selection of G(sub)I/G(sub)II test ratios and a basis for computing the mode I and mode II components of measured delamination toughness. The MMB test was demonstrated using AS4/PEEK (APC2) unidirectional laminates. The MMB test introduced in this paper is rather simple and is believed to offer several advantages over most current mixed-mode test.
575 citations
••
TL;DR: Of the candidate indices evaluated, an index constructed according to the formula, beta power/(alpha power + theta power), reflected task engagement best, and was judged on the basis of their relative strength in exhibiting expected feedback control system phenomena.
573 citations
Authors
Showing all 16015 results
Name | H-index | Papers | Citations |
---|---|---|---|
Daniel J. Jacob | 162 | 656 | 76530 |
Donald R. Blake | 118 | 727 | 49697 |
Veerabhadran Ramanathan | 100 | 301 | 47561 |
Raja Parasuraman | 91 | 402 | 41455 |
Robert W. Platt | 88 | 638 | 31918 |
James M. Russell | 87 | 691 | 29383 |
Daniel J. Inman | 83 | 918 | 37920 |
Antony Jameson | 79 | 474 | 31518 |
Ya-Ping Sun | 79 | 277 | 28722 |
Patrick M. Crill | 79 | 228 | 20850 |
Richard B. Miles | 78 | 759 | 25239 |
Patrick Minnis | 77 | 490 | 23403 |
Robert W. Talbot | 77 | 297 | 19783 |
Raphael T. Haftka | 76 | 773 | 28111 |
Jack E. Dibb | 75 | 344 | 18399 |