Pacific Northwest National Laboratory

About: Pacific Northwest National Laboratory is a facility organization based out in Richland, Washington, United States. It is known for research contribution in the topics: Catalysis & Aerosol. The organization has 11581 authors who have published 27934 publications receiving 1120489 citations. The organization is also known as: PNL & PNNL.

Optimization of mesoporous carbon structures for lithium–sulfur battery applications

Abstract: Mesoporous carbon (MC) with tunable pore sizes (22 nm, 12 nm, 7 nm, and 3 nm) and pore volumes (from 1.3 to 4.8 cm3 g−1) containing sulfur in the pores was studied as a mesoporous carbon–sulfur (MCS) composite electrode for lithium–sulfur (Li–S) batteries. Systematic investigation of these MCS composites reveals that MC with a larger pore volume can hold a higher maximum sulfur loading, but overall the battery performance is very similar for different MCS composites at full sulfur-filling conditions (i.e., the condition at which the sulfur loading approaches the maximum limit set by the pore volume of the individual MC and, therefore, the pores of each MC are fully filled by sulfur). For the same MC, partial sulfur-filling (i.e., the condition at which the sulfur loading is lower than the maximum limit and, therefore, the pores are only partially filled with sulfur) leads to an improved initial discharge capacity and cycle stability, probably because of improved electrical and ionic transport during electrochemical reactions. Based on this understanding, an MCS composite electrode using MC with a large pore volume, partial sulfur filling, and a novel surface modification was designed for Li–S batteries. An initial capacity of ∼1390 mA h g−1 (based on sulfur) and a capacity retention of ∼840 mA h g−1 over 100 cycles at a 0.1 C rate were obtained using MC (22 nm, 4.8 cm3 g−1) with 50 wt% sulfur loading and a commercially available Clevios P (poly(3,4-ethylenedioxythiophene)poly(styrenesulfonate) (PEDT/PSS)) coating.

High-energy lithium metal pouch cells with limited anode swelling and long stable cycles

Abstract: Lithium metal anodes have attracted much attention as candidates for high-energy batteries, but there have been few reports of long cycling behaviour, and the degradation mechanism of realistic high-energy Li metal cells remains unclear. Here, we develop a prototypical 300 Wh kg−1 (1.0 Ah) pouch cell by integrating a Li metal anode, a LiNi0.6Mn0.2Co0.2O2 cathode and a compatible electrolyte. Under small uniform external pressure, the cell undergoes 200 cycles with 86% capacity retention and 83% energy retention. In the initial 50 cycles, flat Li foil converts into large Li particles that are entangled in the solid-electrolyte interphase, which leads to rapid volume expansion of the anode (cell thickening of 48%). As cycling continues, the external pressure helps the Li anode maintain good contact between the Li particles, which ensures a conducting percolation pathway for both ions and electrons, and thus the electrochemical reactions continue to occur. Accordingly, the solid Li particles evolve into a porous structure, which manifests in substantially reduced cell swelling by 19% in the subsequent 150 cycles. Much has been said about the high-energy, long-lasting potential of Li metal batteries, and yet little has been demonstrated at the cell scale. Here, Jun Liu and colleagues demonstrate a Li metal pouch cell with a 300 Wh kg−1 energy density and a 200-cycle lifetime.

Process development for hydrothermal liquefaction of algae feedstocks in a continuous-flow reactor

Abstract: Wet algae slurries can be converted into an upgradeable biocrude by hydrothermal liquefaction (HTL). High levels of carbon conversion to gravity separable biocrude product were accomplished at relatively low temperature (350 °C) in a continuous-flow, pressurized (sub-critical liquid water) environment (20 MPa). As opposed to earlier work in batch reactors reported by others, direct oil recovery was achieved without the use of a solvent and biomass trace components were removed by processing steps so that they did not cause process difficulties. High conversions were obtained even with high slurry concentrations of up to 35 wt.% of dry solids. Catalytic hydrotreating was effectively applied for hydrodeoxygenation, hydrodenitrogenation, and hydrodesulfurization of the biocrude to form liquid hydrocarbon fuel. Catalytic hydrothermal gasification was effectively applied for HTL byproduct water cleanup and fuel gas production from water soluble organics, allowing the water to be considered for recycle of nutrients to the algae growth ponds. As a result, high conversion of algae to liquid hydrocarbon and gas products was found with low levels of organic contamination in the byproduct water. All three process steps were accomplished in bench-scale, continuous-flow reactor systems such that design data for process scale-up was generated.

The Physics of the B Factories

Abstract: This work is on the Physics of the B Factories. Part A of this book contains a brief description of the SLAC and KEK B Factories as well as their detectors, BaBar and Belle, and data taking related issues. Part B discusses tools and methods used by the experiments in order to obtain results. The results themselves can be found in Part C.