Showing papers by "Research Triangle Park published in 2022"

Pyrolysis processing of PFAS-impacted biosolids, a pilot study

Abstract: Concentrations of per- and poly-fluoroalkyl substances (PFAS) present in wastewater treatment biosolids are a growing concern. Pyrolysis is a thermal treatment technology for biosolids that can produce a useful biochar product with reduced levels of PFAS and other contaminants. In August 2020, a limited-scope study investigated target PFAS removal of a commercial pyrolysis system processing biosolid with the analysis of 41 target PFAS compounds in biosolids and biochar performed by two independent laboratories. The concentrations of 21 detected target compounds in the input biosolids ranged between approximately 2 µg/kg and 85 µg/kg. No PFAS compounds were detected in the biochar. The PFAS concentrations in the biochar were assumed to equal the compounds' minimum detection limits (MDLs). The pyrolysis system's target PFAS removal efficiencies (REs) were estimated to range between >81.3% and >99.9% (mean >97.4%) with the lowest REs being associated with the lowest detected PFAS concentrations and the highest MDLs. No information on non-target PFAS compounds in influent or effluent media or products of incomplete combustion was considered. Selected gaseous emissions were measured by Fourier transform infrared spectroscopy and gas chromatography time-of-flight mass spectrometry to provide additional information on air emissions after process controls. This limited-scope study indicated that additional research to further understand this process is warranted.Implications: Development of alternative approaches to manage PFAS-impacted biosolids is of emerging international importance. A commercially operating biosolid pyrolysis process was shown to lower target PFAS levels in produced biochar. Additional research is warranted to understand all potential PFAS transformation emission routes and optimal air pollution emissions control strategies for this technology class.

Review of the Use of Liquid Chromatography-Tandem Mass Spectrometry in Clinical Laboratories: Part I-Development.

Abstract: The process of method development for a diagnostic assay based on liquid chromatography-tandem mass spectrometry (LC-MS/MS) involves several disparate technologies and specialties. Additionally, method development details are typically not disclosed in journal publications. Method developers may need to search widely for pertinent information on their assay(s). This review summarizes the current practices and procedures in method development. Additionally, it probes aspects of method development that are generally not discussed, such as how exactly to calibrate an assay or where to place quality controls, using examples from the literature. This review intends to provide a comprehensive resource and induce critical thinking around the experiments for and execution of developing a clinically meaningful LC-MS/MS assay.

Impact of anthropogenic heat emissions on meteorological parameters and air quality in Beijing using a high-resolution model simulation

Abstract: Anthropogenic heat emissions (AHE) play an important role in modulating the atmospheric thermodynamic and kinetic properties within the urban planetary boundary layer, particularly in densely populated megacities like Beijing. In this study, we estimate the AHE by using a Large-scale Urban Consumption of energY (LUCY) model and further couple LUCY with a high-resolution regional chemical transport model to evaluate the impact of AHE on atmospheric environment in Beijing. In areas with high AHE, the 2-m temperature (T2) increased to varying degrees and showed distinct diurnal and seasonal variations with maxima in night and winter. The increase in 10-m wind speed (WS10) and planetary boundary layer height (PBLH) exhibited slight diurnal variations but showed significant seasonal variations. Further, the systematic continuous precipitation increased by 2.1 mm due to the increase in PBLH and water vapor in upper air. In contrast, the precipitation in local thermal convective showers increased little because of the limited water vapor. Meanwhile, the PM2.5 reduced in areas with high AHE because of the increase in WS10 and PBLH and continued to reduce as the pollution levels increased. In contrast, in areas where prevailing wind direction was opposite to that of thermal circulation caused by AHE, the WS10 reduced, leading to increased PM2.5. The changes of PM2.5 illustrated that a reasonable AHE scheme might be an effective means to improve the performance of PM2.5 simulation. Besides, high AHE aggravated the O3 pollution in urban areas due to the reduction in NOx.

Green metrics in pharmaceutical development

Abstract: This short review presents an overview of key metrics that have been used to assess the ‘greenness’ of pharmaceutical processes in development in the larger context of environmental sustainability. The green metrics cover areas of resource efficiency (mass and energy); environment, health, and safety considerations; and life cycle assessment. There is also a discussion of currently unmet needs in the area that need enhanced focus.

Inactivation of MS2 bacteriophage on copper film deployed in high touch areas of a public transport system

Abstract: Abstract Although SARS-CoV-2 is primarily an airborne risk, the COVID-19 pandemic also highlighted the need for self-disinfection surfaces that could withstand the demand of high occupant densities characteristic of public transportation systems. The aim of this study was to evaluate the durability and antiviral activity of a copper film deployed for 90 days in two high touch locations within an active metropolitan bus and railcar. The antiviral efficacy of this copper film after being deployed in transit vehicles for 90 days (deployed copper film) was then compared to new (unused) copper film to determine if frequent touches and cleaning protocols could decrease the efficacy of the copper films. Deployed copper film, new copper film, and aluminium foil (positive control) coupons were inoculated with ~1 × 106 MS2 virus particles, allowed a contact time of either 5- or 10-min, and analysed for residual viral infectiousness. On both new and deployed copper films, MS2 was completely inactivated (≥5 log reduction) at both time points. These results suggest that the copper film may provide the durability demanded by high touch public spaces while maintaining the antiviral activity necessary to reduce exposure risk and viral transmission via surfaces in public transportation settings.

Experimental verification of principal losses in a regulatory particulate matter emissions sampling system for aircraft turbine engines

Abstract: A sampling system for measuring emissions of nonvolatile particulate matter (nvPM) from aircraft gas turbine engines has been developed to replace the use of smoke number and is used for internatio...

Efficacy of detergent-based cleaning methods against coronavirus MHV-A59 on porous and non-porous surfaces

Abstract: This study evaluated the efficacy of detergent-based surface cleaning methods against Murine Hepatitis Virus A59 (MHV) as a surrogate coronavirus for SARS-CoV-2. MHV (5% soil load in culture medium or simulated saliva) was inoculated onto four different high-touch materials [stainless steel (SS), Acrylonitrile Butadiene Styrene plastic (ABS), Formica, seat fabric (SF)]. Immediately and 2-hr post-inoculation, coupons were cleaned (damp wipe wiping) with and without pretreatment with detergent solution or 375 ppm hard water. Results identified that physical removal (no pretreatment) removed >2.3 log10 MHV on ABS, SS, and Formica when surfaces were cleaned immediately. Pretreatment with detergent or hard water increased effectiveness over wet wiping 2-hr post-inoculation; pretreatment with detergent significantly increased (p ≤ 0.05) removal of MHV in simulated saliva, but not in culture media, over hard water pretreatment (Formica and ABS). Detergent and hard water cleaning methods were ineffective on SF under all conditions. Overall, efficacy of cleaning methods against coronaviruses are material- and matrix-dependent; pre-wetting surfaces with detergent solutions increased efficacy against coronavirus suspended in simulated saliva. This study provides data highlighting the importance of incorporating a pre-wetting step prior to detergent cleaning and can inform cleaning strategies to reducing coronavirus surface transmission.

Evaluation of surface disinfection methods to inactivate the beta coronavirus Murine Hepatitis Virus

Abstract: The list of EPA-approved disinfectants for coronavirus features many products for use on hard, non-porous materials. There are significantly fewer products registered for use on porous materials. Further, many common, high-touch surfaces fall in between non-porous materials such as glass and porous materials such as soft fabrics. The objective of this study was to assess the efficacy of selected commercially available disinfectant products against coronaviruses on common, high-touch surfaces. Four disinfectants (Clorox Total 360, Bleach solution, Vital Oxide, and Peroxide Multi-Surface Cleaner) were evaluated against Murine Hepatitis Virus A59 (MHV) as a surrogate coronavirus for SARS-CoV-2. MHV in cell culture medium was inoculated onto four materials: stainless steel, latex-painted drywall tape, Styrene Butadiene rubber (rubber), and bus seat fabric. Immediately (T0) or 2-hr (T2) post-inoculation, disinfectants were applied by trigger-pull or electrostatic sprayer and either held for recommended contact times (Spray only) or immediately wiped (Spray and Wipe). Recovered infectious MHV was quantified by median tissue culture infectious dose assay. Bleach solution, Clorox Total 360, and Vital Oxide were all effective (>3-log10 reduction or complete kill of infectious virus) with both the Spray Only and Spray and Wipe methods on stainless steel, rubber, and painted drywall tape when used at recommended contact times at both T0 and T2 hr. Multi-Surface Cleaner unexpectedly showed limited efficacy against MHV on stainless steel within the recommended contact time; however, it showed increased (2.3 times greater efficacy) when used in the Spray and Wipe method compared to Spray Only. The only products to achieve a 3-log10 reduction on fabric were Vital Oxide and Clorox Total 360; however, the efficacy of Vital Oxide against MHV on fabric was reduced to below 3-log10 when applied by an electrostatic sprayer compared to a trigger-pull sprayer. This study highlights the importance of considering the material, product, and application method when developing a disinfection strategy for coronaviruses on high-touch surfaces.

A New Low-Activity Nuclear Density Gauge for Soil Density Measurements

Abstract: For decades, nuclear density gauges have been used to measure the density and moisture content of soil during compaction testing in road and embankment construction. Worldwide regulatory agencies consider nuclear density gauges as controlled devices because of their inclusion of radioisotope sources. Regulatory requirements, such as the need for licensing, special storage, special transportation procedures, gauge operator training, and personal dosimetry, have become burdens for gauge users. Recently, a new nuclear density gauge for measuring soil wet density was declared exempt from licensing and other nuclear regulatory requirements in the United States. The new gauge uses an extremely low-activity radioisotope source. It further incorporates a separate probe operating on electromagnetic principles for soil moisture measurement or any other moisture measurement method the user desires. This paper presents the design features and measurement properties of this low-activity nuclear density gauge and its associated moisture probe. The measurement properties were determined from laboratory and field studies that were conducted in North Carolina, United States. These studies showed that the sensitivity and precision of wet density measurements made by the low-activity nuclear density gauge were similar to those made by a conventional nuclear density gauge. The wet density measurements made by the low-activity gauge and conventional gauge showed a strong correlation and agreement. For the two field sites studied, a silty sand subbase and a cement-treated aggregate base course, the dry density agreement between the low-activity nuclear density gauge/moisture probe and the conventional nuclear density gauge was within 3 lb/ft3 (48 kg/m3).

Suspended sediment and discharge dynamics in a glaciated alpine environment: identifying crucial areas and time periods on several spatial and temporal scales in the Ötztal, Austria

Abstract: Abstract. Glaciated high-alpine areas are fundamentally altered by climate change, with well-known implications for hydrology, e.g., due to glacier retreat, longer snow-free periods, and more frequent and intense summer rainstorms. While knowledge on how these hydrological changes will propagate to suspended sediment dynamics is still scarce, it is needed to inform mitigation and adaptation strategies. To understand the processes and source areas most relevant to sediment dynamics, we analyzed discharge and sediment dynamics in high temporal resolution as well as their patterns on several spatial scales, which to date few studies have done. We used a nested catchment setup in the Upper Ötztal in Tyrol, Austria, where high-resolution (15 min) time series of discharge and suspended sediment concentrations are available for up to 15 years (2006–2020). The catchments of the gauges in Vent, Sölden and Tumpen range from 100 to almost 800 km2 with 10 % to 30 % glacier cover and span an elevation range of 930 to 3772 m a.s.l. We analyzed discharge and suspended sediment yields (SSY), their distribution in space, their seasonality and spatial differences therein, and the relative importance of short-term events. We complemented our analysis by linking the observations to satellite-based snow cover maps, glacier inventories, mass balances and precipitation data. Our results indicate that the areas above 2500 m a.s.l., characterized by glacier tongues and the most recently deglaciated areas, are crucial for sediment generation in all sub-catchments. This notion is supported by the synchronous spring onset of sediment export at the three gauges, which coincides with snowmelt above 2500 m but lags behind spring discharge onsets. This points at a limitation of suspended sediment supply as long as the areas above 2500 m are snow-covered. The positive correlation of annual SSY with glacier cover (among catchments) and glacier mass balances (within a catchment) further supports the importance of the glacier-dominated areas. The analysis of short-term events showed that summer precipitation events were associated with peak sediment concentrations and yields but on average accounted for only 21 % of the annual SSY in the headwaters. These results indicate that under current conditions, thermally induced sediment export (through snow and glacier melt) is dominant in the study area. Our results extend the scientific knowledge on current hydro-sedimentological conditions in glaciated high-alpine areas and provide a baseline for studies on projected future changes in hydro-sedimentological system dynamics.

The Estrogen Receptor α Cistrome in Human Endometrium and Epithelial Organoids

Abstract: Endometrial health is affected by molecular processes that underlie estrogen responses. We assessed estrogen regulation of endometrial function by integrating the estrogen receptor α (ESR1) cistromes and transcriptomes of endometrial biopsies taken from the proliferative and mid-secretory phases of the menstrual cycle together with hormonally stimulated endometrial epithelial organoids. The cycle stage-specific ESR1 binding sites were determined by chromatin immunoprecipitation and next-generation sequencing and then integrated with changes in gene expression from RNA sequencing data to infer candidate ESR1 targets in normal endometrium. Genes with ESR1 binding in whole endometrium were enriched for chromatin modification and regulation of cell proliferation. The distribution of ESR1 binding sites in organoids was more distal from gene promoters when compared to primary endometrium and was more similar to the proliferative than the mid-secretory phase ESR1 cistrome. Inferred organoid estrogen/ESR1 candidate target genes affected formation of cellular protrusions and chromatin modification. Comparison of signaling effected by candidate ESR1 target genes in endometrium vs organoids reveals enrichment of both overlapping and distinct responses. Our analysis of the ESR1 cistromes and transcriptomes from endometrium and organoids provides important resources for understanding how estrogen affects endometrial health and function.

Sex differences in inflammatory cytokine levels following synthetic cathinone self-administration in rats

Abstract: Synthetic cathinones are used as stimulants of abuse. Many abused drugs, including stimulants, activate nuclear factor-κB (NF-κB) transcription leading to increases in NF-κB-regulated pro-inflammatory cytokines, and the level of inflammation appears to correlate with length of abuse. The purpose of this study was to measure the profile of IL-1α, IL-1β, IL-6, CCL2 and TNF-α in brain and plasma to examine if drug exposure alters inflammatory markers. Male and female Sprague-Dawley rats were trained to self-administer α-pyrrolidinopentiophenone (α-PVP) (0.1 mg/kg/infusion), 4-methylmethcathinone (4MMC) (0.5 mg/kg/infusion), or saline through autoshaping, and then self-administered for 21 days during 1 h (short access; ShA) or 6 h (long access; LgA) sessions. Separate rats were assigned to a naive control group. Cytokine levels were examined in amygdala, hippocampus, hypothalamus, prefrontal cortex, striatum, thalamus, and plasma. Rats acquired synthetic cathinone self-administration, and there were no sex differences in drug intake. Synthetic cathinone self-administration produced sex differences in IL-1α, IL-1β, IL-6, CCL2 and TNF-α levels. There were widespread increases in inflammatory cytokines in the brains of male rats compared to females, particularly for 4MMC, whereas females were more likely to show increased inflammatory cytokines in plasma compared to saline groups than males. Furthermore, these sex differences in cytokine levels were more common after LgA access to synthetic cathinones than ShA. These results suggest that synthetic cathinone use likely produces sex-selective patterns of neuroinflammation during the transition from use to abuse. Consequently, treatment need may differ depending on the progression of synthetic cathinone abuse and based on sex.

Critical Reviews Should Illuminate a Path toward Impactful and Fruitful Lines of Research

Abstract: ADVERTISEMENT RETURN TO ISSUEEditorialNEXTCritical Reviews Should Illuminate a Path toward Impactful and Fruitful Lines of ResearchLaura L. McConnell*Laura L. McConnellCrop Science Division, Regulatory Scientific Affairs, Bayer U.S. LLC, St. Louis, Missouri 63017, United States*Email: [email protected]More by Laura L. McConnellhttps://orcid.org/0000-0001-6142-0656, Coralia Osorio RoaCoralia Osorio RoaUniversidad Nacional de Colombia, Departamento de Química, Bogotá AA 14490, ColombiaMore by Coralia Osorio Roahttps://orcid.org/0000-0001-6222-0138, and Thomas F. HofmannThomas F. HofmannChair of Food Chemistry and Molecular Sensory Science, Technical University of Munich, Lise-Meitner-Strasse 34, D-85354 Freising-Weihenstephan, GermanyMore by Thomas F. Hofmannhttps://orcid.org/0000-0003-4057-7165Cite this: J. Agric. Food Chem. 2022, 70, 8, 2425–2426Publication Date (Web):February 24, 2022Publication History Received26 January 2022Accepted26 January 2022Published online24 February 2022Published inissue 2 March 2022https://doi.org/10.1021/acs.jafc.2c00727Copyright © 2022 American Chemical SocietyRIGHTS & PERMISSIONSArticle Views455Altmetric-Citations-LEARN ABOUT THESE METRICSArticle Views are the COUNTER-compliant sum of full text article downloads since November 2008 (both PDF and HTML) across all institutions and individuals. These metrics are regularly updated to reflect usage leading up to the last few days.Citations are the number of other articles citing this article, calculated by Crossref and updated daily. Find more information about Crossref citation counts.The Altmetric Attention Score is a quantitative measure of the attention that a research article has received online. Clicking on the donut icon will load a page at altmetric.com with additional details about the score and the social media presence for the given article. Find more information on the Altmetric Attention Score and how the score is calculated. Share Add toView InAdd Full Text with ReferenceAdd Description ExportRISCitationCitation and abstractCitation and referencesMore Options Share onFacebookTwitterWechatLinked InReddit PDF (482 KB) Get e-Alerts Get e-Alerts

Ammonium-adduct chemical ionization to investigate anthropogenic oxygenated gas-phase organic compounds in urban air

Abstract: Abstract. Volatile chemical products (VCPs) and other non-combustion-related sources have become important for urban air quality, and bottom-up calculations report emissions of a variety of functionalized compounds that remain understudied and uncertain in emissions estimates. Using a new instrumental configuration, we present online measurements of oxygenated VCPs in a U.S. megacity over a 10-day wintertime sampling period, when biogenic sources and photochemistry were less active. Measurements were conducted at a rooftop observatory in upper Manhattan, New York City, USA using a Vocus chemical ionization time-of-flight mass spectrometer with ammonium (NH4+) as the reagent ion operating at 1 Hz. The range of observations spanned volatile, intermediate-volatility, and semi-volatile organic compounds with targeted analyses of ~150 ions whose likely assignments included a range of functionalized compound classes such as glycols, glycol ethers, acetates, acids, alcohols, acrylates, esters, ethanolamines, and ketones that are found in various consumer, commercial, and industrial products. Their concentrations varied as a function of wind direction with enhancements over the highly-populated areas of the Bronx, Manhattan, and parts of New Jersey, and included abundant concentrations of acetates, acrylates, ethylene glycol, and other commonly-used oxygenated compounds. The results provide top-down constraints on wintertime emissions of these oxygenated/functionalized compounds with ratios to common anthropogenic marker compounds and compares their relative abundances to two regionally-resolved emissions inventories used in urban air quality models.

A method for predicting hydrogen and oxygen isotope distributions across a region's river network using reach-scale environmental attributes

Abstract: Abstract. Stable isotope ratios (isotope values) of surface water reflect hydrological pathways, mixing processes, and atmospheric exchange within catchments. Development of maps of surface water isotope values (isoscapes) is limited by methods to interpolate point measures across river networks. Catchment attributes that alter surface water isotope values affect downstream river reaches via flow, but some attributes such as artificial dams are no more likely to affect nearby unconnected catchments than distant ones. Hence, simple distance-based geospatial and statistical interpolation methods used to develop isoscapes for precipitation and terrestrial systems are less appropriate for river networks. We used a water-balance-based method to map long-term average δ2H and δ18O for New Zealand rivers, incorporating corrections using catchment environmental predictors. Inputs to the model are national rainfall precipitation isoscapes, a digital elevation layer, a national river water isotope monitoring dataset (3 years of monthly sampling at 58 sites), and river environmental databases covering around 600 000 reaches and over 400 000 km of rivers. Much of the spatial variability in δ2H and δ18O of New Zealand river water was explained using the initial combination of precipitation isoscapes and a simple water balance model. δ2H and δ18O isoscapes produced by subsequently applying residuals from the water balance model as a correction factor across the river network using regression kriging showed improved fits to the validation data compared to the correction using ordinary kriging. Predictors of high importance in the regression included upstream lake and wetland area, which was not strongly spatially autocorrelated nationally. Hence, additional hydrological process information such as evaporation effects can be incorporated into river isoscapes using regression kriging of residuals. The resulting isoscapes have potential applications in ecological, hydrological, and provenance studies that consider differences between surface water isotope values and those of other components of the hydrological cycle (e.g. subsurface runoff or local precipitation).