University of Science and Technology Beijing

About: University of Science and Technology Beijing is a education organization based out in Beijing, China. It is known for research contribution in the topics: Microstructure & Alloy. The organization has 41558 authors who have published 44473 publications receiving 623229 citations. The organization is also known as: Beijing Steel and Iron Institute.

Succinonitrile as a Versatile Additive for Polymer Electrolytes

Abstract: Solid polymer electrolytes with high ionic conductivities are prepared by using poly(ethylene oxide) (PEO) and poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) as polymer matrixes, succinonitrile (SN) as an additive, and lithium bis-trifluoromethanesulfonimide (LiTFSI) and lithium bisperfluoroethylsulfonylimide (LiBETI) as salts. In these systems, the introduction of succinonitrile into the polymer electrolytes increases the material's ionic conductivity and conveys excellent mechanical properties. The described composites, with their beneficial combination of mechanical and electric properties, are expected to have significant potential for lithium batteries.

Effects of AL addition on microstructure and mechanical properties of AlxCoCrFeNi High-entropy alloy

Abstract: The effects of Al on microstructure and mechanical properties of AlxCoCrFeNi (x=0.1, 0.75 and 1.5) high-entropy alloys were systematically studied by using various characterization methods. It was found that the crystalline structure of AlxCoCrFeNi high-entropy alloy varies markedly with Al content, which changes from the initial single face-centered cubic (fcc) to fcc plus ordered body-centered cubic (bcc) structure (B2) and then to a duplex bcc structure (A2+B2) as the Al content is increased. The chemical composition analysis reveals that Al primarily partitions to B2 phase, suggesting Al is a stabilizer of B2 structure. With increasing Al content, more Ni and Al partition to the B2 phase due to the very negative mixing enthalpy of Ni and Al, and another phase enriched in Cr and Fe transforms from fcc to disordered bcc. Nano indentation measurements show that the hardness of AlxCoCrFeNi high-entropy alloy increases with Al content, accompanied by the decrease of ductility. The stability of single-phase solid solution in AlxCoCrFeNi HEAs is deduced from various criteria. Combined with the experiment results of other similar HEA systems, such as AlxCoCrFeNiCu, the effects of Al addition on the microstructure of AlxCoCrFeNi HEAs are discussed based on the Gibbs free energy of all competing phases and the fundamental properties of constituent elements. The aim of current study is to provide experimental evidence to establish a correlation between the microstructure and mechanical properties to search for high-entropy alloys with higher performances.

Substantial emission reductions from Chinese power plants after the introduction of ultra-low emissions standards

Abstract: In 2014, China introduced an ultra-low emissions (ULE) standards policy for renovating coal-fired power-generating units to limit SO2, NOx and particulate matter (PM) emissions to 35, 50 and 10 mg m−3, respectively. The ULE standard policy had ambitious levels (surpassing those of all other countries) and implementation timeline. We estimate emission reductions associated with the ULE policy by constructing a nationwide, unit-level, hourly-frequency emissions dataset using data from a continuous emissions monitoring systems network covering 96–98% of Chinese thermal power capacity during 2014–2017. We find that between 2014 and 2017 China’s annual power emissions of SO2, NOx and PM dropped by 65%, 60% and 72%, respectively. Our estimated emissions using actual monitoring data are 18–92% below other recent estimates. We detail the technologies used to meet the ULE standards and the determinants of compliance, underscoring the importance of ex post evaluation and providing insights for other countries wishing to reduce their power emissions. In 2014 China proposed an ultra-low emissions policy for coal-fired power plants to reduce emissions. Using comprehensive nationwide stack emissions monitoring data, Tang et al. show reductions in excess of 60% for SO2, NOx and particulate matter emissions since 2014, even as power generation overall increased.

A Transforming Metal Nanocomposite with Large Elastic Strain, Low Modulus, and High Strength

Abstract: Freestanding nanowires have ultrahigh elastic strain limits (4 to 7%) and yield strengths, but exploiting their intrinsic mechanical properties in bulk composites has proven to be difficult. We exploited the intrinsic mechanical properties of nanowires in a phase-transforming matrix based on the concept of elastic and transformation strain matching. By engineering the microstructure and residual stress to couple the true elasticity of Nb nanowires with the pseudoelasticity of a NiTi shape-memory alloy, we developed an in situ composite that possesses a large quasi-linear elastic strain of over 6%, a low Young's modulus of ~28 gigapascals, and a high yield strength of ~1.65 gigapascals. Our elastic strain-matching approach allows the exceptional mechanical properties of nanowires to be exploited in bulk materials.