Institution
Vikram Sarabhai Space Centre
Facility•Thiruvananthapuram, India•
About: Vikram Sarabhai Space Centre is a facility organization based out in Thiruvananthapuram, India. It is known for research contribution in the topics: Aerosol & Ultimate tensile strength. The organization has 2092 authors who have published 3058 publications receiving 47975 citations. The organization is also known as: VSSC.
Papers published on a yearly basis
Papers
More filters
••
TL;DR: In this article, a simple finite element formulation is presented for evaluating the thermal postbuckling behavior of rectangular plates, in the form of linear thermal loads and ratios of nonlinear to linear thermal load for various values of the central deflection and for three sets of boundary conditions.
47 citations
••
TL;DR: In this paper, the influence of Scandium (Sc) content (0.025 and 0.25 ) on microstructure, texture and mechanical properties of a thermo-mechanically processed AA2195 alloy has been investigated.
47 citations
••
47 citations
••
TL;DR: In this article, the effect of shear rate on the viscosity of linear low-density polyethylene (LLDPE)/ethylene vinyl acetate (EVA) blends was investigated with special reference to the effects of blend ratio, temperature, shear rates, compatibilization, and dynamic vulcanization.
Abstract: The melt rheological properties of linear low-density polyethylene (LLDPE)/ethylene vinyl acetate (EVA) blends were investigated with special reference to the effect of blend ratio, temperature, shear rate, compatibilization, and dynamic vulcanization. The melt viscosity of the blends determined with a capillary rheometer is found to decrease with an increase of shear rate, which is an indication of pseudoplastic behavior. The viscosity of the blend was found to be a nonadditive function of the viscosities of the component polymers. A negative deviation was observed because of the interlayer slip between the polar EVA and the nonpolar LLDPE phases. The melt viscosity of these blends decreases with the increased concentration of EVA. The morphology of the extrudate of the blends at different shear rates and blend ratios was studied and the size and distribution of the domains were examined by scanning electron microscopy. The morphology was found to depend on shear rate and blend ratio. Compatibilization of the blends with phenolic- and maleic-modified LLDPE increased the melt viscosity at lower wt % of compatibilizer and then leveled off. Dynamic vulcanization is found to increase the melt viscosity at a lower concentration of DCP. The effect of temperature on melt viscosity of the blends was also studied. Finally, attempts were made to correlate the experimental data on melt viscosity and cocontinuity region with different theoretical models. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3210–3225, 2002
47 citations
••
TL;DR: In this article, a diglycidyl ether of bisphenol-A (DGEBA) epoxy resin was modified with poly(ether ether ketone) with pendent methyl groups (PEEKM).
Abstract: A diglycidyl ether of bisphenol-A (DGEBA) epoxy resin was modified with poly(ether ether ketone) with pendent methyl groups (PEEKM). PEEKM was synthesised from methyl hydroquinone and 4,4′-difluorobenzophenone and characterised. Blends of epoxy resin and PEEKM were prepared by melt blending. The blends were transparent in the uncured state and gave single composition dependent Tg. The Tg-composition behaviour of the uncured blends has been studied using Gordon–Taylor, Kelley–Bueche and Fox equations. The scanning electron micrographs of extracted fracture surfaces revealed that reaction induced phase separation occurred in the blends. Cocontinuous morphology was obtained in blends containing 15 phr PEEKM. Two glass transition peaks corresponding to epoxy rich and thermoplastic rich phases were observed in the dynamic mechanical spectrum of the blends. The crosslink density of the blends calculated from dynamic mechanical analysis was less than that of unmodified epoxy resin. The tensile strength, flexural strength and modulus were comparable to that of the unmodified epoxy resin. It was found from fracture toughness measurements that PEEKM is an effective toughener for DDS cured epoxy resin. Fifteen phr PEEKM having cocontinuous morphology exhibited maximum increase in fracture toughness. The increase in fracture toughness was due to crack path deflection, crack pinning, crack bridging by dispersed PEEKM and local plastic deformation of the matrix. The exceptional increase in fracture toughness of 15 phr blend was attributed to the cocontinuous morphology of the blend. Finally it was observed that the thermal stability of epoxy resin was not affected by the addition of PEEKM.
47 citations
Authors
Showing all 2111 results
Name | H-index | Papers | Citations |
---|---|---|---|
M. Santosh | 103 | 1344 | 49846 |
Sabu Thomas | 102 | 1554 | 51366 |
S. Suresh Babu | 70 | 498 | 17113 |
K. Krishna Moorthy | 54 | 263 | 9749 |
Sathianeson Satheesh | 53 | 172 | 11099 |
M. Y. Hussaini | 49 | 207 | 16794 |
J.R. Banerjee | 44 | 146 | 5620 |
C. P. Reghunadhan Nair | 37 | 181 | 4825 |
K. N. Ninan | 36 | 159 | 4156 |
Anil Bhardwaj | 35 | 230 | 4527 |
Ivatury S. Raju | 33 | 121 | 6626 |
Venkata Sai Kiran Chakravadhanula | 32 | 102 | 3011 |
P.K. Sinha | 32 | 118 | 2918 |
J.-P. St.-Maurice | 31 | 113 | 3446 |
Subramaniam Gopalakrishnan | 28 | 123 | 2951 |